Abstract: Electrolytic capacitors are notorious for short lifetimes in high-temperature applications such asLED light bulbs. The careful selection of these devices with proper interpretation of their specifications isessential to ensure that they do not compromise the life of the end product. This application notediscusses this problem with electrolytic capacitors in LED light bulbs and provides an analysis that showshow it is possible to use electrolytics in such products.
上傳時間： 2013-11-17
上傳用戶：asdfasdfd
Digitemp Junior – An RS-232 Port-Powered Digital Thermometer Digitemp Jr. is a device that is designed to measure and report ambient temperature. When connected to an RS-232 port on any PC, it will periodically measure and report in ASCII form the ambient temperature in degrees Celsius. These temperature readings can be monitored with any terminal program. If the terminal program supports capture to disk, the temperature readings can be saved to disk for further analysis with a spreadsheet program or other data analysis tool. The simple ASCII output format of Digitemp Jr. makes it rel- atively easy to write custom software for receiving, recording, and analyzing ambient temperature data. Best of all, Digitemp Jr. requires no external power sup- plies or batteries. It is powered directly by the RS-232 port.
標簽： Microchip 232 PIC RS
上傳時間： 2013-10-21
上傳用戶：baitouyu
為了使音頻信號分析儀小巧可靠，成本低廉，設計了以2片MSP430F1611單片機為核心的系統。該系統將音頻信號送入八階巴特沃茲低通濾波器，對信號進行限幅放大、衰減、電平位移、緩沖，并利用一單片機負責對前級處理后的模擬信號進行采樣，將采集得到的音頻信號進行4 096點基2的FFT計算，并對信號加窗函數提高分辨率，另一單片機負責對信號的分析及控制顯示設備。此設計精確的測量了音頻信號的功率譜、周期性、失真度指標，達到較高的頻率分辨率，并能將測量結果通過紅外遙控器顯示在液晶屏上。 Abstract: o make the audio signal analyzer cheaper， smaller and more reliable， this system sends the audio signal to the eight-order butterworth filter， and then amplifies， attenuates， buffers it in a limiting range， transfers the voltage level of the signal before utilizing two MSP430F1611 MCU to realize the audio analysis. One is charged for sampling and dealing with the processed audio signal collected by the 4096 point radix-2 FFT calculation and imposes the window function to improve the frequency resolution. The other one controls the display and realizes the spectrum， periodicity， power distortion analysis in high resolution which is displayed in the LCD screen through the infrared remote control.
上傳時間： 2013-12-11
上傳用戶：jasonheung
設計了一種基于PIC16C71單片機的數字水溫配制閥。該配制閥采用NTC熱敏電阻作溫度傳感器，與固定電阻組成簡單分壓電路作為水溫測量電路，利用PIC16C71單片機內置的8位A/D轉換器把熱敏電阻上的模擬電壓轉換為數字量，PIC16C71單片機控制直流電機驅動混水閥調節冷熱水的混合比例實現水溫調節。給出了控制電路圖，對水溫測量電路的參數選擇和測溫精度作了詳細討論。實驗和分析表明，選用阻值較大的NTC熱敏電阻和分壓電阻可較好地解決熱敏電阻因功耗較大造成的熱擊穿問題。 Abstract: A digital valve for controlling water temperature based on PIC16C71 was presented in this paper.A bleeder circuit which consisted of a NTC thermistor as temperature sensor and a fixed resistance was designed as water temperature measuring circuit.The analog voltage on the thermistor was converted into digital signal by a 8-bit A/D converter embedded in PIC16C71. Based on the digital signal， the MCU PIC16C71 drived the valve by a DC motor to adjust the water temperature through adjusting the proportion of hot water and cold water.The circuit diagram of controller was given，the principle，the component parameters and the accuracy of measuring temperatures were also dissertated in detail. It was found by experiment and analysis that thermal breakdown of thermistor caused by high power could be solved by selecting thermistor and fixed resistance with high impedance value.
上傳時間： 2013-11-08
上傳用戶：Yue Zhong
在航電系統維護過程中，為解決定位故障的效率和降低維修成本等問題，提出了基于ICD（Interface Control Document，接口控制文件）的1553B總線的信息監控系統模型。該系統運用數據采集卡對總線中傳輸?shù)男盘?hào)有無失真、偏差等電氣特性進行檢測，并使用1553B通訊卡通過測控軟件LabWindows/CVI編程與ICD數據庫的動態鏈接，實現總線信息的解析和故障的判斷。與傳統的維護過程相比，這種模型能夠從信號的電氣特性以及信息的解析等全方位的去檢測判斷故障的來源，并且能夠廣泛在其他1553B總線系統內擴展應用。驗證表明該監控系統可以對總線信息進行快速有效地監測分析，能滿足應用需求。 Abstract: In the process of avionics system maintenance， to solve the problems such as improving the efficiency of fast orientation to troubles and reducing maintenance cost， system of 1553B bus information monitor model based on ICD was proposed. The system observed whether the data which transmitted on the bus appear distortion and deviation by using data acquisition card. And using 1553B communication card programming of the measure software LabWindows/CVI and the dynamic linking of ICD database， message analysis and fault estimation could be realized. Compared with traditional maintenance， this model can all-dimensionally detect and analyze the source of faults from both electrical characteristics of the signal and message analysis， and it can be widely applied in the other 1553B system. Experiment shown that this monitor system can effectively detect and analyze the bus message and can meet the application requirements.
標簽： 1553B 總線 信息監控
上傳時間： 2013-11-23
上傳用戶：18752787361
Digitemp Jr. is a device that is designed to measure and report ambient temperature. When connected to an RS-232 port on any PC, it will periodically measure and report in ASCII form the ambient temperature in degrees Celsius. These temperature readings can be monitored with any terminal program. If the terminal program supports capture to disk, the temperature readings can be saved to disk for further analysis with a spreadsheet program or other data analysis tool. The simple ASCII output format of Digitemp Jr. makes it relatively easy to write custom software for receiving, recording, and analyzing ambient temperature data. Best of all, Digitemp Jr. requires no external power supplies or batteries. It is powered directly by the RS-232 port.
上傳時間： 2013-10-20
上傳用戶：Maple
以太網和CAN總線應用廣泛，但由于其通信協議不同，兩種總線器件間無法進行數據通信，因此，設計了基于CP2200與C8051F040的以太網總線與CAN總線接口轉換電路，并給出部分相關硬件電路與軟件設計分析。在保證數據完整和協議可靠的前提下，通過握手協議和簡化的以太網協議，不僅實現了以太網數據與CAN數據的轉發，同時還順利的解決了以太網的高速性與CAN的低速率沖突，以及兩者數據包之間的大小不同的矛盾。 Abstract: In the development of actual application， Ethernet and CAN bus are used very extensively. Owing to its various communication protocols， the communicating between two kinds of bus device can’t be carried out. Therefore， in order to solve this problem， the Ethernet-CAN bus interface circuit based on CP2200 and C8051F040 was designed in this paper， and part of the related hardware circuit and software design analysis were given. On the condition of data’s integrity and protocols’reliability， through the handshaking protocols and the simplified the Ethernet protocol， not only the data switching between CAN and Ethernet was realized， but also the differ in velocity and packet size was solved.
標簽： C8051F040 CAN 以太網 轉換
上傳時間： 2013-10-15
上傳用戶：Ants
詳細介紹工控軟件組態王與單片機多機串口通訊的設計原理。分析組態王提供的直接與單片機串口通信方法的優點，給出系統基于RS-485總線傳輸?shù)慕涌陔娐吩韴D。根據組態王提供的通訊協議和單片機多機串口通訊的原理，給出程序設計流程與思路。 Abstract: In this paper，the design principle of communication between multi-SCM and KingView by serial ports is described in detail.We analysis the advantage of method supplied by KingView,by which KingView can communicate with serial ports of SCM directly，and provide the system’s interface circuit based on the RS-485transmission line.We provide flow diagram of programming and thinking on the basis of communication protocol supplied by KingView and principle of communication among multi-SCM through serial ports.
標簽： 工控軟件 單片機 串口通訊 多機
上傳時間： 2013-12-19
上傳用戶：tecman
介紹一種基于C8051單片機的動態心電監護系統。該系統由兩部分組成：以C8051F320單片機為核心的數據采集裝置和以PC機為平臺的分析處理系統。硬件電路功耗低，由單片機自帶的USB接口將數據傳送給PC機。軟件平臺采用LabVIEW可視化虛擬儀器系統開發平臺，將傳統儀器的功能模塊集成到計算機中，用戶可通過修改虛擬儀器的程序改變其功能。采用USB接口實時傳輸心電數據，并將數據采集模塊設計為計算機外設，使該系統高速快捷、小巧便攜。 Abstract: In this design，a low-cost ECG electrocardiogram monitoring system is introduced，which consists of two parts:data acquisition device based on C8051F320and PC terminal as the analysis and processing system.The system is low-power consumption，the data is transmitted to the PC terminal by USB interface of the C8051F320.By using the visible virtual instrument system developing platform LabVIEW，the traditional instruments function modules are integrated into the computer，so the user can modify virtual instrument software to change its function to meet their needs.Using USB in-terface to realize real-time ECG data transmission，in addition，ECG data acquisition module is designed as the computer peripheral，which makes the syetem high-speed and portable.
標簽： C8051F320 心電監護 系統設計
上傳時間： 2013-11-13
上傳用戶：zhangzhenyu
介紹一種簡單射頻識別系統設計。該設計包括閱讀器、應答器和線圈3部分。由單片機控制閱讀器向應答器發射無線信號，并接收應答器回送的信號，再通過分析回送信號識別物品。閱讀器和應答器之間以半雙工通信方式通信。 Abstract: A simple design of radio frequency identification system is given in this paper.The design includes reader,responder and winding.Through MCU，signals are sent to responder from reader，then corresponding signals are sent back. According to the analysis of the signals sent back，the objects can be identified.Half-duplex communication is adopted? between? reader? and? responder.
標簽： 51單片機 無線識別 裝置
上傳時間： 2013-10-11
上傳用戶：plsee
蟲蟲下載站版權所有 京ICP備2021023401號-1
<strike id="ygcqw"></strike>
<strike id="ygcqw"></strike>