調制解調課程設計 16QAM調制解調代碼。包括星座圖，頻譜分析，誤碼率分析。-16QAM modulation and demodulation curriculum design code modulation and demodulation. Including constellation, spectrum analysis, bit error rate analysis.
為解決輸油管道溫度壓力參數實時監測的問題，設計了以C8051F930單片機作為控制核心的超低功耗輸油管道溫度壓力遠程監測系統。現場儀表使用高精度電橋采集數據，通過433 MHz短距離無線通信網絡與遠程終端RTU進行通信，RTU通過GPRS網絡與PC上位機進行遠程數據傳輸，在上位機中實現數據存儲和圖形化界面顯示，從而實現輸油管道溫度壓力參數的實時監測和異常報警。經實驗證明，該系統的12位數據采集精度滿足設計要求，漏碼率小于1%，正常工作時間超過5個月，能實時有效地監測輸油管道的溫度壓力參數，節省大量人工成本，有效預防管道參數異常造成的經濟損失和環境污染。
Abstract:
In order to solve the problems on real-time monitoring of pipeline temperature and pressure parameters， the ultra-low power remote pipeline temperature and pressure monitoring system was designed by using the single chip processor C8051F930 as the control core. The high-precision electric bridge was used in field instruments for data collection， the 433MHz short-range wireless communication network was used to make communication between field instrument and RTU， the GPRS was used by the RTU to transmit data to the PC host computer， and the data was stored and displayed in the PC host computer， so the real-time monitoring and exception alerts of pipeline temperature and pressure parameters were achieved. The experiment proves that the system of which error rate is less than 1% over five months working with the 12-bit data acquisition accuracy can effectively monitor the pipeline temperature and pressure parameters in real time， it saves a lot of labor costs and effectively prevents environmental pollution and economic losses caused by abnormal channel parameters.
This a software runing on the matlab, it is used in the channel coding simulation.
It include DVB-S2 LDPC, Covolution turbo, and block turbo code, You can choose which channel coding to run.
it run the encoder and add white noise in the channel, then it run the decoder, and compute the error rate.
the c languge is used for the GPS field.The pogram is the PARITY CHECK ,which is one kind data of the GPS data .and it is used for correcting one bit error
This code was used for making the practical measurements in section 2.3 of my thesis. This Matlab code allows an OFDM signal to be generated based on an input data file. The data can be random data, a grey scale image, a wave file, or any type of file. The generated OFDM signal is stored as a windows wave file, allowing it to be viewed, listened to and manipulated in other programs. The modified wave file can then be decoded by the receiver software to extract the original data. This code was developed for the experiments that I performed in my honours thesis, and thus has not been fully debugged.
This is the original code developed for the thesis and so has several problems with it. The BER performance given by the simulations is infact Symbol Error Rate.
基于OFDM的無線寬帶系統仿真It contains mainly two parts, i.e. link-level simulator and system-level simulator.
Link-level simulator focus on a single-cell single-user scenario, where signal is transmitted from tx, and estimated at rx. Comparing the difference in tx/rx signal, the error rate can be found out. The output of the link-level simulator is the BLER/BER vs. SNR mapping table, that can be used for the system-level simulation.
System-level simulator focus on a multi-cell multi-user scenario. For the sake of simplicity, it takes the mapping table aquired in the link-level simulation, measure the actural SNR, and finds the corresponding error rate.
Melp Federal Vocoder 2.4 kbps low bit rate high qualitytexas instrument Melp encoder decoder c-code working great with good quality melp vocoding system
IDCT-M is a medium speed 1D IDCT core
-- it can accept a continous stream of 12-bit input words at a rate of
-- 1 bit/ck cycle, operating at 50MHz speed, it can process MP@ML MPEG video
-- the core is 100％ synthesizable
