/* ********************************************************************************************************* * uC/TCP-IP V2 * The Embedded TCP/IP Suite * * (c) Copyright 2003-2010; Micrium, Inc.; Weston, FL * * All rights reserved. Protected by international copyright laws. * * uC/TCP-IP is provided in source form to registered licensees ONLY. It is * illegal to distribute this source code to any third party unless you receive * written permission by an authorized Micrium representative. Knowledge of * the source code may NOT be used to develop a similar product. * * Please help us continue to provide the Embedded community with the finest * software available. Your honesty is greatly appreciated. * * You can contact us at www.micrium.com. ********************************************************************************************************* */ /* ********************************************************************************************************* * * NETWORK TCP LAYER * (TRANSMISSION CONTROL PROTOCOL) * * Filename : net_tcp.h * Version : V2.10 * Programmer(s) : ITJ ********************************************************************************************************* * Note(s) : (1) Supports Transmission Control Protocol as described in RFC #793 with the following * restrictions/constraints : * * (a) TCP Security & Precedence NOT supported RFC # 793, Section 3.6 * * (b) TCP Urgent Data NOT supported RFC # 793, Section 3.7 * 'The Communication of * Urgent Information' * * (c) The following TCP options NOT supported : * * (1) Window Scale RFC #1072, Section 2 * RFC #1323, Section 2 * (2) Selective Acknowledgement (SACK) RFC #1072, Section 3 * RFC #2018 * RFC #2883 * (3) TCP Echo RFC #1072, Section 4 * (4) Timestamp RFC #1323, Section 3.2 * (5) Protection Against Wrapped Sequences (PAWS) RFC #1323, Section 4 * * (d) #### IP-Options-to-TCP-Connection RFC #1122, Section 4.2.3.8 * Handling NOT supported * * (e) #### ICMP-Error-Message-to-TCP-Connection RFC #1122, Section 4.2.3.9 * Handling NOT currently supported * * (2) TCP Layer assumes/requires Network Socket Layer (see 'net_sock.h MODULE Note #1a2'). ********************************************************************************************************* */ /*$PAGE*/ /* ********************************************************************************************************* * MODULE * * Note(s) : (1) TCP Layer module is NOT required for UDP-to-Application API configuration. * * See also 'net_cfg.h TRANSPORT LAYER CONFIGURATION' * & 'net_cfg.h USER DATAGRAM PROTOCOL LAYER CONFIGURATION'. * * See also 'net_tcp.h Note #2'. * * (2) The following TCP-module-present configuration value MUST be pre-#define'd in * 'net_cfg_net.h' PRIOR to all other network modules that require TCP Layer * configuration (see 'net_cfg_net.h TCP LAYER CONFIGURATION Note #2b') : * * NET_TCP_MODULE_PRESENT ********************************************************************************************************* */ #ifdef NET_TCP_MODULE_PRESENT /* See Note #2. */ /* ********************************************************************************************************* * EXTERNS ********************************************************************************************************* */ #if ((defined(NET_TCP_MODULE)) && \ (defined(NET_GLOBALS_EXT))) #define NET_TCP_EXT #else #define NET_TCP_EXT extern #endif /*$PAGE*/ /* ********************************************************************************************************* * DEFINES ********************************************************************************************************* */ /* ********************************************************************************************************* * TCP HEADER DEFINES * * Note(s) : (1) The following TCP value MUST be pre-#define'd in 'net_def.h' PRIOR to 'net_buf.h' so that * the Network Buffer Module can configure maximum buffer header size (see 'net_def.h TCP * LAYER DEFINES' & 'net_buf.h NETWORK BUFFER INDEX & SIZE DEFINES Note #1') : * * (a) NET_TCP_HDR_SIZE_MAX 60 (NET_TCP_HDR_LEN_MAX * * NET_TCP_HDR_LEN_WORD_SIZE) * * (2) Urgent pointer & data NOT supported (see 'net_tcp.h Note #1b'). ********************************************************************************************************* */ #define NET_TCP_HDR_LEN_MASK 0xF000u #define NET_TCP_HDR_LEN_SHIFT 12u #define NET_TCP_HDR_LEN_NONE 0u #define NET_TCP_HDR_LEN_MIN 5u #define NET_TCP_HDR_LEN_MAX 15u #define NET_TCP_HDR_LEN_WORD_SIZE CPU_WORD_SIZE_32 #define NET_TCP_HDR_SIZE_MIN (NET_TCP_HDR_LEN_MIN * NET_TCP_HDR_LEN_WORD_SIZE) #if 0 /* See Note #1a. */ #define NET_TCP_HDR_SIZE_MAX (NET_TCP_HDR_LEN_MAX * NET_TCP_HDR_LEN_WORD_SIZE) #endif #define NET_TCP_HDR_SIZE_TOT_MIN (NET_IP_HDR_SIZE_TOT_MIN + NET_TCP_HDR_SIZE_MIN) #define NET_TCP_HDR_SIZE_TOT_MAX (NET_IP_HDR_SIZE_TOT_MAX + NET_TCP_HDR_SIZE_MAX) #define NET_TCP_PSEUDO_HDR_SIZE 12u /* = sizeof(NET_TCP_PSEUDO_HDR) */ #define NET_TCP_PORT_NBR_RESERVED NET_PORT_NBR_RESERVED #define NET_TCP_PORT_NBR_NONE NET_TCP_PORT_NBR_RESERVED #define NET_TCP_HDR_URG_PTR_NONE 0x0000u /* See Note #2. */ /*$PAGE*/ /* ********************************************************************************************************* * TCP HEADER FLAG DEFINES * * Note(s) : (1) See 'TCP HEADER Note #2' for flag fields. * * (2) Urgent pointer & data NOT supported (see 'net_tcp.h Note #1b'). ********************************************************************************************************* */ #define NET_TCP_HDR_FLAG_MASK 0x0FFFu #define NET_TCP_HDR_FLAG_NONE DEF_BIT_NONE #define NET_TCP_HDR_FLAG_RESERVED 0x0FE0u /* MUST be '0'. */ #define NET_TCP_HDR_FLAG_URGENT DEF_BIT_05 /* See Note #2. */ #define NET_TCP_HDR_FLAG_ACK DEF_BIT_04 #define NET_TCP_HDR_FLAG_PUSH DEF_BIT_03 #define NET_TCP_HDR_FLAG_RESET DEF_BIT_02 #define NET_TCP_HDR_FLAG_SYNC DEF_BIT_01 #define NET_TCP_HDR_FLAG_FIN DEF_BIT_00 #define NET_TCP_HDR_FLAG_CLOSE NET_TCP_HDR_FLAG_FIN /* ********************************************************************************************************* * TCP FLAG DEFINES ********************************************************************************************************* */ /* ------------------ NET TCP FLAGS ------------------- */ #define NET_TCP_FLAG_NONE DEF_BIT_NONE #define NET_TCP_FLAG_USED DEF_BIT_00 /* TCP conn cur used; i.e. NOT in free TCP conn pool. */ /* ------------------ TCP TX FLAGS ------------------- */ /* TCP tx flags copied from TCP hdr flags. */ #define NET_TCP_FLAG_TX_FIN NET_TCP_HDR_FLAG_FIN #define NET_TCP_FLAG_TX_CLOSE NET_TCP_FLAG_TX_FIN #define NET_TCP_FLAG_TX_SYNC NET_TCP_HDR_FLAG_SYNC #define NET_TCP_FLAG_TX_RESET NET_TCP_HDR_FLAG_RESET #define NET_TCP_FLAG_TX_PUSH NET_TCP_HDR_FLAG_PUSH #define NET_TCP_FLAG_TX_ACK NET_TCP_HDR_FLAG_ACK #define NET_TCP_FLAG_TX_URGENT NET_TCP_HDR_FLAG_URGENT #define NET_TCP_FLAG_TX_BLOCK DEF_BIT_07 /* ------------------ TCP RX FLAGS ------------------- */ #define NET_TCP_FLAG_RX_DATA_PEEK DEF_BIT_08 #define NET_TCP_FLAG_RX_BLOCK DEF_BIT_15 /*$PAGE*/ /* ********************************************************************************************************* * TCP TYPE DEFINES * * Note(s) : (1) NET_TCP_TYPE_&&& #define values specifically chosen as ASCII representations of the TCP * types. Memory displays of TCP types will display with their chosen ASCII names. ********************************************************************************************************* */ /* ------------------ NET TCP TYPES ------------------- */ #if (CPU_CFG_ENDIAN_TYPE == CPU_ENDIAN_TYPE_BIG) #define NET_TCP_TYPE_NONE 0x4E4F4E45u /* "NONE" in ASCII. */ #define NET_TCP_TYPE_CONN 0x54435020u /* "TCP " in ASCII. */ #else #if (CPU_CFG_DATA_SIZE == CPU_WORD_SIZE_32) #define NET_TCP_TYPE_NONE 0x454E4F4Eu /* "NONE" in ASCII. */ #define NET_TCP_TYPE_CONN 0x20504354u /* "TCP " in ASCII. */ #elif (CPU_CFG_DATA_SIZE == CPU_WORD_SIZE_16) #define NET_TCP_TYPE_NONE 0x4F4E454Eu /* "NONE" in ASCII. */ #define NET_TCP_TYPE_CONN 0x43542050u /* "TCP " in ASCII. */ #else /* Dflt CPU_WORD_SIZE_08. */ #define NET_TCP_TYPE_NONE 0x4E4F4E45u /* "NONE" in ASCII. */ #define NET_TCP_TYPE_CONN 0x54435020u /* "TCP " in ASCII. */ #endif #endif /* ********************************************************************************************************* * TCP SEQUENCE NUMBER DEFINES * * Note(s) : (1) TCP initial transmit sequence number is incremented by a fixed value, preferably a large * prime value or a large value with multiple unique factors. * * (a) One reasonable TCP initial transmit sequence number increment value example : * * 65527 = 37 * 23 * 11 * 7 * * * #### NET_TCP_TX_SEQ_NBR_CTR_INC could be developer-configured in 'net_cfg.h'. * * See also 'NET_TCP_TX_GET_SEQ_NBR() Notes #1b2 & #1c2'. ********************************************************************************************************* */ #define NET_TCP_SEQ_NBR_NONE 0u #define NET_TCP_ACK_NBR_NONE NET_TCP_SEQ_NBR_NONE #define NET_TCP_TX_SEQ_NBR_CTR_INC 65527u /* See Note #1. */ #define NET_TCP_ACK_NBR_DUP_WIN_SIZE_SCALE 4 /*$PAGE*/ /* ********************************************************************************************************* * TCP DATA/TOTAL LENGTH DEFINES * * Note(s) : (1) (a) TCP total length #define's (NET_TCP_TOT_LEN) relate to the total size of a complete * TCP packet, including the packet's TCP header. Note that a complete TCP packet MAY * be fragmented in multiple Internet Protocol packets. * * (b) TCP data length #define's (NET_TCP_DATA_LEN) relate to the data size of a complete * TCP packet, equal to the total TCP packet length minus its TCP header size. Note * that a complete TCP packet MAY be fragmented in multiple Internet Protocol packets. ********************************************************************************************************* */ /* See Notes #1a & #1b. */ #define NET_TCP_DATA_LEN_MIN 0u #define NET_TCP_TOT_LEN_MIN (NET_TCP_HDR_SIZE_MIN + NET_TCP_DATA_LEN_MIN) #define NET_TCP_TOT_LEN_MAX (NET_IP_TOT_LEN_MAX - NET_IP_HDR_SIZE_MIN ) #define NET_TCP_DATA_LEN_MAX (NET_TCP_TOT_LEN_MAX - NET_TCP_HDR_SIZE_MIN) /*$PAGE*/ /* ********************************************************************************************************* * TCP SEGMENT SIZE DEFINES * * Note(s) : (1) (a) RFC # 879, Section 3 states that the TCP Maximum Segment Size "counts only * data octets in the segment, ... not the TCP header or the IP header". * * (b) RFC #1122, Section 4.2.2.6 requires that : * * (1) "The MSS value to be sent in an MSS option must be less than or equal to * * (A) MMS_R - 20 * * where MMS_R is the maximum size for a transport-layer message that can * be received." * * (2) "If an MSS option is not received at connection setup, TCP MUST assume a * default send MSS of 536 (576 - 40)." * * See also 'net_ip.h IP DATA/TOTAL LENGTH DEFINES Note #1'. ********************************************************************************************************* */ /* See Note #1. */ #define NET_TCP_MAX_SEG_SIZE_DFLT (NET_IP_MAX_DATAGRAM_SIZE_DFLT - NET_IP_HDR_SIZE_MIN - NET_TCP_HDR_SIZE_MIN) #define NET_TCP_MAX_SEG_SIZE_DFLT_RX NET_TCP_DATA_LEN_MAX /* See Note #1b1. */ #define NET_TCP_MAX_SEG_SIZE_DFLT_TX NET_TCP_MAX_SEG_SIZE_DFLT /* See Note #1b2. */ #define NET_TCP_MAX_SEG_SIZE_NONE 0u #define NET_TCP_MAX_SEG_SIZE_MIN NET_TCP_MAX_SEG_SIZE_DFLT #define NET_TCP_MAX_SEG_SIZE_MAX NET_TCP_DATA_LEN_MAX #define NET_TCP_SEG_LEN_MIN NET_TCP_DATA_LEN_MIN #define NET_TCP_SEG_LEN_MAX NET_TCP_DATA_LEN_MAX #define NET_TCP_SEG_LEN_SYNC 1u #define NET_TCP_SEG_LEN_FIN 1u #define NET_TCP_SEG_LEN_CLOSE NET_TCP_SEG_LEN_FIN #define NET_TCP_SEG_LEN_ACK 0u #define NET_TCP_SEG_LEN_RESET 0u #define NET_TCP_SEG_LEN_PROBE 0u #define NET_TCP_DATA_LEN_TX_SYNC 0u #define NET_TCP_DATA_LEN_TX_FIN 0u #define NET_TCP_DATA_LEN_TX_CLOSE NET_TCP_DATA_LEN_TX_FIN #define NET_TCP_DATA_LEN_TX_ACK 0u #define NET_TCP_DATA_LEN_TX_PROBE_NO_DATA 0u #define NET_TCP_DATA_LEN_TX_PROBE_DATA 1u #define NET_TCP_DATA_LEN_TX_RESET 0u #define NET_TCP_TX_PROBE_DATA 0x00u /* ********************************************************************************************************* * TCP WINDOW SIZE DEFINES * * Note(s) : (1) Although NO RFC specifies the absolute minimum TCP connection window size value allowed, * RFC #793, Section 3.7 'Data Communication : Managing the Window' states that for "the * window ... there is an assumption that this is related to the currently available data * buffer space available for this connection". ********************************************************************************************************* */ #define NET_TCP_WIN_SIZE_NONE 0u #define NET_TCP_WIN_SIZE_MIN NET_TCP_MAX_SEG_SIZE_MIN #define NET_TCP_WIN_SIZE_MAX DEF_INT_16U_MAX_VAL /*$PAGE*/ /* ********************************************************************************************************* * TCP HEADER OPTIONS DEFINES * * Note(s) : (1) See the following RFC's for TCP options summary : * * (a) RFC # 793, Section 3.1 'Header Format : Options' * (b) RFC #1122; Sections 4.2.2.5, 4.2.2.6 * * (2) TCP option types are encoded in the first octet for each TCP option as follows : * * -------- * | TYPE | * -------- * * The TCP option type value determines the TCP option format : * * (a) The following TCP option types are single-octet TCP options -- i.e. the option type * octet is the ONLY octet for the TCP option. * * (1) TYPE = 0 End of Options List * (2) TYPE = 1 No Operation * * * (b) All other TCP options MUST be multi-octet TCP options (see RFC #1122, Section 4.2.2.5) : * * ------------------------------ * | TYPE | LEN | TCP OPT | * ------------------------------ * * where * TYPE Indicates the specific TCP option type * LEN Indicates the total TCP option length, in octets, including * the option type & the option length octets * TCP OPT Additional TCP option octets, if any, that contain the remaining * TCP option information * * The following TCP option types are multi-octet TCP options where the option's second * octet specify the total TCP option length, in octets, including the option type & the * option length octets : * * (1) TYPE = 2 Maximum Segment Size See RFC # 793, Section 3.1 'Header Format : * Options : Maximum Segment Size'; * RFC #1122, Section 4.2.2.6; * RFC # 879, Section 3 * * (2) TYPE = 3 Window Scale See 'net_tcp.h Note #1c1' * (3) TYPE = 4 SACK Allowed See 'net_tcp.h Note #1c2' * (4) TYPE = 5 SACK Option See 'net_tcp.h Note #1c2' * (5) TYPE = 6 Echo Request See 'net_tcp.h Note #1c3' * (6) TYPE = 7 Echo Reply See 'net_tcp.h Note #1c3' * (7) TYPE = 8 Timestamp See 'net_tcp.h Note #1c4' * * (3) TCP header allows for a maximum option list length of 40 octets : * * NET_TCP_HDR_OPT_SIZE_MAX = NET_TCP_HDR_SIZE_MAX - NET_TCP_HDR_SIZE_MIN * * = 60 - 20 * * = 40 * * (4) 'NET_TCP_OPT_SIZE' MUST be pre-defined PRIOR to all definitions that require TCP option * size data type. ********************************************************************************************************* */ /*$PAGE*/ #define NET_TCP_HDR_OPT_END_LIST 0u #define NET_TCP_HDR_OPT_NOP 1u #define NET_TCP_HDR_OPT_MAX_SEG_SIZE 2u #define NET_TCP_HDR_OPT_WIN_SCALE 3u #define NET_TCP_HDR_OPT_SACK_PERMIT 4u #define NET_TCP_HDR_OPT_SACK 5u #define NET_TCP_HDR_OPT_ECHO_REQ 6u #define NET_TCP_HDR_OPT_ECHO_REPLY 7u #define NET_TCP_HDR_OPT_TS 8u #define NET_TCP_HDR_OPT_PAD NET_TCP_HDR_OPT_END_LIST #define NET_TCP_HDR_OPT_LEN_END_LIST 1u #define NET_TCP_HDR_OPT_LEN_NOP 1u #define NET_TCP_HDR_OPT_LEN_MAX_SEG_SIZE 4u #define NET_TCP_HDR_OPT_LEN_WIN_SCALE 3u #define NET_TCP_HDR_OPT_LEN_SACK_PERMIT 2u #define NET_TCP_HDR_OPT_LEN_ECHO_REQ 6u #define NET_TCP_HDR_OPT_LEN_ECHO_REPLY 6u #define NET_TCP_HDR_OPT_LEN_TS 10u #define NET_TCP_HDR_OPT_LEN_SACK_MIN 6u #define NET_TCP_HDR_OPT_LEN_SACK_MAX 38u #define NET_TCP_HDR_OPT_LEN_MIN 1u #define NET_TCP_HDR_OPT_LEN_MIN_LEN 2u #define NET_TCP_HDR_OPT_LEN_MAX 38u typedef CPU_INT32U NET_TCP_OPT_SIZE; /* TCP opt size data type (see Note #4). */ #define NET_TCP_HDR_OPT_SIZE_WORD (sizeof(NET_TCP_OPT_SIZE)) #define NET_TCP_HDR_OPT_SIZE_MAX (NET_TCP_HDR_SIZE_MAX - NET_TCP_HDR_SIZE_MIN) #define NET_TCP_HDR_OPT_NBR_MIN 0u #define NET_TCP_HDR_OPT_NBR_MAX (NET_TCP_HDR_OPT_SIZE_MAX / NET_TCP_HDR_OPT_SIZE_WORD) #define NET_TCP_HDR_OPT_IX NET_TCP_HDR_SIZE_MIN /*$PAGE*/ /* ********************************************************************************************************* * TCP OPTION CONFIGURATION TYPE DEFINES * * Note(s) : (1) NET_TCP_OPT_CFG_TYPE_&&& #define values specifically chosen as ASCII representations of * the TCP option configuration types. Memory displays of TCP option configuration buffers * will display the TCP option configuration TYPEs with their chosen ASCII names. ********************************************************************************************************* */ /* ---------------- TCP OPT CFG TYPES ----------------- */ #if (CPU_CFG_ENDIAN_TYPE == CPU_ENDIAN_TYPE_BIG) #define NET_TCP_OPT_CFG_TYPE_NONE 0x4E4F4E45u /* "NONE" in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_MAX_SEG_SIZE 0x4D535320u /* "MSS " in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_WIN_SCALE 0x57494E20u /* "WIN " in ASCII (see 'net_tcp.h Note #1c1'). */ #define NET_TCP_OPT_CFG_TYPE_SACK_PERMIT 0x53434B50u /* "SCKP" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_SACK 0x5341434Bu /* "SACK" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REQ 0x45524551u /* "EREQ" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REPLY 0x4543484Fu /* "ECHO" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_TS 0x54532020u /* "TS " in ASCII (see 'net_tcp.h Note #1c4'). */ #else #if (CPU_CFG_DATA_SIZE == CPU_WORD_SIZE_32) #define NET_TCP_OPT_CFG_TYPE_NONE 0x454E4F4Eu /* "NONE" in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_MAX_SEG_SIZE 0x2053534Du /* "MSS " in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_WIN_SCALE 0x204E4957u /* "WIN " in ASCII (see 'net_tcp.h Note #1c1'). */ #define NET_TCP_OPT_CFG_TYPE_SACK_PERMIT 0x504B4353u /* "SCKP" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_SACK 0x4B434153u /* "SACK" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REQ 0x51455245u /* "EREQ" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REPLY 0x4F484345u /* "ECHO" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_TS 0x20205354u /* "TS " in ASCII (see 'net_tcp.h Note #1c4'). */ #elif (CPU_CFG_DATA_SIZE == CPU_WORD_SIZE_16) #define NET_TCP_OPT_CFG_TYPE_NONE 0x4F4E454Eu /* "NONE" in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_MAX_SEG_SIZE 0x534D2053u /* "MSS " in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_WIN_SCALE 0x4957204Eu /* "WIN " in ASCII (see 'net_tcp.h Note #1c1'). */ #define NET_TCP_OPT_CFG_TYPE_SACK_PERMIT 0x4353504Bu /* "SCKP" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_SACK 0x41534B43u /* "SACK" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REQ 0x52455145u /* "EREQ" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REPLY 0x43454F48u /* "ECHO" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_TS 0x53542020u /* "TS " in ASCII (see 'net_tcp.h Note #1c4'). */ #else /* Dflt CPU_WORD_SIZE_08. */ #define NET_TCP_OPT_CFG_TYPE_NONE 0x4E4F4E45u /* "NONE" in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_MAX_SEG_SIZE 0x4D535320u /* "MSS " in ASCII. */ #define NET_TCP_OPT_CFG_TYPE_WIN_SCALE 0x57494E20u /* "WIN " in ASCII (see 'net_tcp.h Note #1c1'). */ #define NET_TCP_OPT_CFG_TYPE_SACK_PERMIT 0x53434B50u /* "SCKP" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_SACK 0x5341434Bu /* "SACK" in ASCII (see 'net_tcp.h Note #1c2'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REQ 0x45524551u /* "EREQ" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_ECHO_REPLY 0x4543484Fu /* "ECHO" in ASCII (see 'net_tcp.h Note #1c3'). */ #define NET_TCP_OPT_CFG_TYPE_TS 0x54532020u /* "TS " in ASCII (see 'net_tcp.h Note #1c4'). */ #endif #endif /*$PAGE*/ /* ********************************************************************************************************* * TCP CONNECTION TIMEOUT DEFINES * * Note(s) : (1) (a) (1) RFC #1122, Section 4.2.2.13 'DISCUSSION' states that "the graceful close algorithm * of TCP requires that the connection state remain defined on (at least) one end of * the connection, for a timeout period of 2xMSL ... During this period, the (remote * socket, local socket) pair that defines the connection is busy and cannot be reused". * * (2) The following sections reiterate that the TIME-WAIT state timeout scalar is two * maximum segment lifetimes (2 MSL) : * * (A) RFC #793, Section 3.9 'Event Processing : SEGMENT ARRIVES : * Check Sequence Number : TIME-WAIT STATE' * (B) RFC #793, Section 3.9 'Event Processing : SEGMENT ARRIVES : * Check FIN Bit : TIME-WAIT STATE' * * (b) (1) RFC #793, Section 3.3 'Sequence Numbers : Knowing When to Keep Quiet' states that * "the Maximum Segment Lifetime (MSL) is ... to be 2 minutes. This is an engineering * choice, and may be changed if experience indicates it is desirable to do so". * * (2) Microsoft Corporation's Windows XP defaults MSL to 15 seconds. ********************************************************************************************************* */ /* Max seg timeout (see Note #1b) : */ #define NET_TCP_CONN_TIMEOUT_MAX_SEG_MIN_SEC ( 0u ) /* ... min = 0 seconds */ #define NET_TCP_CONN_TIMEOUT_MAX_SEG_MAX_SEC ( 2u * DEF_TIME_NBR_SEC_PER_MIN) /* ... max = 2 minutes */ #define NET_TCP_CONN_TIMEOUT_MAX_SEG_DFLT_SEC ( 15u ) /* ... dflt = 15 seconds */ #define NET_TCP_CONN_TIMEOUT_MAX_SEG_SCALAR 2u /* ... scalar (see Note #1a). */ #define NET_TCP_CONN_TIMEOUT_CONN_DFLT_SEC (120u * DEF_TIME_NBR_SEC_PER_MIN) /* Dflt conn timeout = 120 minutes */ #define NET_TCP_CONN_TIMEOUT_USER_DFLT_SEC ( 30u * DEF_TIME_NBR_SEC_PER_MIN) /* Dflt user timeout = 30 minutes */ /*$PAGE*/ /* ********************************************************************************************************* * TCP CONNECTION STATES * * Note(s) : (1) See the following RFC's for TCP state machine summary : * * (a) RFC # 793; Sections 3.2, 3.4, 3.5, 3.9 * (b) RFC #1122; Sections 4.2.2.8, 4.2.2.10, 4.2.2.11, 4.2.2.13, 4.2.2.18, 4.2.2.20 * * (2) (a) #### Additional closing-data-available state used for closing connections to allow the * application layer to receive any remaining data. * * See also 'net_tcp.c NetTCP_RxPktConnHandlerFinWait1() Note #2f5A2', * 'net_tcp.c NetTCP_RxPktConnHandlerFinWait2() Note #2f5B', * 'net_tcp.c NetTCP_RxPktConnHandlerClosing() Note #2d2B2a1B', * & 'net_tcp.c NetTCP_RxPktConnHandlerLastAck() Note #2d2A1b'. ********************************************************************************************************* */ #define NET_TCP_CONN_STATE_NONE 0u #define NET_TCP_CONN_STATE_FREE 1u #define NET_TCP_CONN_STATE_CLOSED 10u #define NET_TCP_CONN_STATE_LISTEN 20u #define NET_TCP_CONN_STATE_SYNC_RXD 30u #define NET_TCP_CONN_STATE_SYNC_RXD_PASSIVE 31u #define NET_TCP_CONN_STATE_SYNC_RXD_ACTIVE 32u #define NET_TCP_CONN_STATE_SYNC_TXD 35u #define NET_TCP_CONN_STATE_CONN 40u #define NET_TCP_CONN_STATE_FIN_WAIT_1 50u #define NET_TCP_CONN_STATE_FIN_WAIT_2 51u #define NET_TCP_CONN_STATE_CLOSING 52u #define NET_TCP_CONN_STATE_TIME_WAIT 53u #define NET_TCP_CONN_STATE_CLOSE_WAIT 55u #define NET_TCP_CONN_STATE_LAST_ACK 56u #define NET_TCP_CONN_STATE_CLOSING_DATA_AVAIL 59u /* See Note #2a. */ /* ********************************************************************************************************* * TCP CONNECTION QUEUE STATES ********************************************************************************************************* */ #define NET_TCP_RX_Q_STATE_NONE 0u #define NET_TCP_RX_Q_STATE_CLOSED 100u #define NET_TCP_RX_Q_STATE_CLOSING 101u #define NET_TCP_RX_Q_STATE_SYNC 110u #define NET_TCP_RX_Q_STATE_CONN 111u #define NET_TCP_TX_Q_STATE_NONE 0u #define NET_TCP_TX_Q_STATE_CLOSED 200u #define NET_TCP_TX_Q_STATE_CLOSING 201u #define NET_TCP_TX_Q_STATE_SYNC 210u #define NET_TCP_TX_Q_STATE_CONN 211u #define NET_TCP_TX_Q_STATE_SUSPEND 215u #define NET_TCP_TX_Q_STATE_CLOSED_SUSPEND 220u #define NET_TCP_TX_Q_STATE_CLOSING_SUSPEND 221u /*$PAGE*/ /* ********************************************************************************************************* * TCP CONNECTION CODE DEFINES **************
上傳時間： 2015-11-22
上傳用戶：the same kong
常用接插件USB座 SD卡 TF卡 RJ45 AD集成庫ALITUM庫49個合集（原理圖庫+PCB封裝庫），集成封裝庫型號列表：Library Component Count : 49Name Description----------------------------------------------------------------------------------------------------3F07 立體聲耳機插座6.3mm插簧 6.3mm插簧Battery 備份電池CON 2X16 DIN41612 DIN 41612CON 2X32 DIN41612 DIN 41612CON50A D Connector 15 VGAD Connector 9 串口DB25 并口DG141 DIMM-100 接插件EMIF 接插件FIN 散熱片F(xiàn)PC-30P FPC排線連接器FPC-40P FPC排線連接器HR5803 以太網接口HR911103A 網絡接口HR911105A 以太網接口Header 10 接插件Header 10X2 接插件Header 14X2A 接插件Header 15X2 接插件Header 16 接插件Header 16X2 接插件Header 17X2 接插件Header 2 接插件Header 2X2 接插件Header 3 接插件Header 30 接插件Header 32X2 接插件Header 4 接插件Header 40 接插件Header 5X2 接插件Header 6 接插件Header 7X2 接插件Header 8 接插件Header 8X2 接插件Header_AMP50 控制器接插件LCD_CON37 LCD接口Light_Pipe 燈柱PJ-306 立體聲耳機插座PWRCON 直流電源端子RCA RCA Phono JackSDCARD SD卡自彈SDCARD-M TF卡槽SU-25-3 接線叉USB USB接口USB_M Micro/Mini USBZIF20 接插件
上傳時間： 2021-11-21
上傳用戶：slq1234567890
本研究提出了一套完整的基于Linux嵌入式平臺的EtherCAT主站系統設計方案，旨在打通整個EtherCAT協議技術環節。從主站和從站的硬件層面到軟件層面再到上位機軟件，開發出整套擁有自主知識產權的EtherCAT主站系統。設計EtherCAT從站模塊，選用從站控制芯片ET1100設計通信板，STM32單片機設計控制板，將通信板和控制板通過SPI總線接口組合，組成兩套從站模塊，分別實現數字輸入信號檢測和模擬輸入信號檢測的功能。設計EtherCAT主站模塊，選用基于AM3358處理器的BeagleBone Black作為Linux嵌入式開發平臺，并且在該平臺上運行集成Xenomai實時補丁的Linux操作系統，接著在操作系統上構建IgH EtherCAT Master for Linux開源框架和配置開發環境，最后基于這套開源框架進行應用程序的設計，完成整套主站模塊設計。設計EtherCAT主站程序的兩種交互模式，一種是基于命令行操作的控制臺模式，還有一種是基于Qt開發的圖形用戶界面模式。用戶可以通過任意模式，實現過程數據通信和服務數據通信的數據讀寫，并且執行一些其他的必要功能操作。結果表明，從站模塊的基本功能實現，可以有效檢測輸入的數字信號和模擬信號。主站模塊的基本功能實現，可以與從站模塊建立起有效的過程數據通信和服務數據通信，性能上同步誤差在ns級，報文的傳輸時間在us級，通訊抖動在us級別，可以滿足工業控制系統對實時性的要求。控制臺模式和圖形用戶界面模式交互有效。
上傳時間： 2022-05-22
上傳用戶：aben
成功的RF設計必須仔細注意整個設計過程中每個步驟及每個細節，這意味著必須在設計開始階段就要進行徹底的，仔細的規劃，并對每個設計步驟的進展進行全面持續的評估，而這種細致的設計技巧正是國內大多數電子企業文化所欠缺的近幾年來，由于藍芽設備、無線局域網絡（WLAN）設備，和行動電話的需求與成長，促使業者越來越關注RF電路設計的技巧。從過去到現在，RF電路板設計如同電磁干擾（EM）問題一樣，一直是工程師們最難掌控的部份，甚至是夢魔。若想要一次就設計成功，必須事先仔細規劃和注重細節才能奏效。射頻（RF）電路板設計由于在理論上還有很多不確定性，因此常被形容為一種L黑色藝術」（black art）。但這只是一種以偏蓋全的觀點，RF電路板設計還是有許多可以遵循的法則。不過，在實際設計時，真正實用的技巧是當這些法則因各種限制而無法實施時，如何對它們進行折衷處理，重要的RF設計課題包括：阻抗和阻抗匹配、絕緣層材料和層迭板、波長和諧波.等，本文將集中探討與RF電路板分區設計有關的各種問題
上傳時間： 2022-06-21
上傳用戶：
BBB開發板資料，含原理圖、PCB、BOM和生產資料。
標簽： BBB開發板 beaglebone-black
上傳時間： 2022-07-18
上傳用戶：
蟲蟲下載站版權所有 京ICP備2021023401號-1
