uninstall the device in the "Computer Management" pannel.在設備管理器中卸載已有驅動install PL2303-Prolific_DriverInstaller_v1200安裝壓縮包中的PL2303-Prolific_DriverInstaller_v1200restart your computer.重啟計算機
標簽： pl2303 win10 驅動
上傳時間： 2022-03-13
上傳用戶：jiabin
M.NT68676.2A is a monitor control board, which is suitable for Asia-Pacific market. It can supportLED/LCD panels which resolution is up to 2048×1152.M.NT68676.2A can synchronize with computer automatically. Synchronization requires thesynchronous signal which horizontal and vertical sync are separated.M.NT68676.2A can support dynamic contrast control, headphone input and Digital volume controlsimultaneously.
標簽： 樂華驅動板
上傳時間： 2022-03-13
上傳用戶：kent
本系統采用電動機電樞供電回路串接采樣電阻的方式來實現對小型直流有刷電動機的轉速測量。該系統主要由二階低通濾波電路,小信號放大電路、單片機測量顯示電路、開關穩壓電源電路等組成。同時自制電機測速裝置,用高頻磁環作為載體,用線圈繞制磁環,利用電磁感應原理檢測電機運行時的漏磁,將變化的磁場信號轉化為磁環上的感應電流。用信號處理單元電路將微弱電信號轉化為脈沖信號,送由單片機檢測,從而達到準確測量電機的速度的要求。In this system, the sampling resistance of armature power supply circuit is connected in series to measure the speed of small DC brush motor. The system is mainly composed of second-order low-pass filter circuit, small signal amplifier circuit, single-chip measurement and display circuit, switching regulated power supply circuit and so on. At the same time, the self-made motor speed measuring device uses high frequency magnetic ring as the carrier, coil winding magnetic ring, and electromagnetic induction principle to detect the leakage of magnetic field during the operation of the motor, which converts the changed magnetic field signal into the induced current on the magnetic ring. The weak electric signal is transformed into pulse signal by signal processing unit circuit, which is sent to single chip computer for detection, so as to meet the requirement of accurate measurement of motor speed.
標簽： 直流電動機
上傳時間： 2022-03-26
上傳用戶：
以倉庫智能改造為背景,主要介紹單片機和上位機之間通信網絡和通信協議的選擇,MODBUS協議通信指令和功能碼使用,重點闡述了基于RS-485總線的MODBUS通信協議在上位機和單片機之間的串行通信,實現上位機對單片機設備的遠程控制和信息采集的功能。Based on the intelligent warehouse transformation as the background,mainly introduces between MCU and PC communication network and the choice of communication protocol,instruction and the function code using the MODBUS protocol communication,expounds the MODBUS communication protocol based on RS-485 bus serial communication between PC and single chip microcomputer,PC remote control of single chip computer equipment and the function of information collection.
標簽： RS-485總線 modbus 單片機
上傳時間： 2022-03-26
上傳用戶：
以AT89S52單片機為控制核心,采用電容降壓技術,Buck電路拓?fù)?PWM驅動模塊和功率器件散熱設計,通過高速的數據采集、主功率輸入輸出模塊和控制模塊,設計一種新型智能車載充電器.在充電過程中,通過負脈沖瞬間放電實現對鉛酸蓄電池的再生修復,提高電池的有效容量,延長使用壽命.該充電器體積小、速度快、效率高、可靠性好.With AT89S52 single chip computer as the control core,a new type of intelligent car-carried charger was designed by using capacitance step-down technology,Buck circuit topology,PWM driving module and power device heat dissipation design,through high-speed data acquisition,main power input and output module and control module.In the charging process,the regeneration and repair of lead-acid batteries are realized by instantaneous discharge of negative pulse,which improves the effective capacity of batteries and prolongs their service life.The charger has the advantages of small size,fast speed,high efficiency and good reliability.
標簽： 車載充電器
上傳時間： 2022-03-27
上傳用戶：
靜電放電（Electrostatic Discharge，ESD）是構成集成電路可靠性的主要因素之一，存在于生產到使用的每一個環節，并成為開發新一代工藝技術的難點之一，近年來，對ESD的研究也因而越來越受到重視，仿真工具在ESD領域的應用使得ESD防護的研究變得更為便利，可大幅縮短研發周期然而，由于ESD現象復雜的物理機制，極端的電場及溫度條件，以及ESD仿真中頻繁的不收斂現象，都使得FSD的仿真變得極為困難本文詳細闡述了ESD的來源、造成的危害以及如何測試集成電路的防靜電沖擊能力，并基于 Sentaurus軟件，對ESD防護器件展開了的分析、研究，內容包括1）掌握ESD保護的基本理論、測試方法和防護機理2）研究了工藝仿真流程的步驟以及網格定義在工藝仿真中的重要性，并對網格定義的方法進行了探討3）硏究了器件仿真流程以及器件仿真中的物理模型和模型函數，并對描述同一物理機制的的各種不同模型展開對比分析.主要包括傳輸方程模型、能帶模型、各種遷移率退化模型、雪崩離化模型和復合模型4）研究了雙極型晶體管和可控硅（Silicon Controlled rectifier，SCR）防護器件的仿真，并通過對仿真結果的分析，研究了ESD保護器件在ESD應力作用下的工作機理關鍵詞：靜電放電；網格；器件仿真；雙極型晶體管；可控硅
上傳時間： 2022-03-30
上傳用戶：
在傳統智能小車驅動電路設計中,較多考慮使用直流電機還是步進電機,電機功率、能耗等性能參數。使用具有armCortexM4內核的STM32嵌入式平臺控制四輪的4個直流電機。文章基于PWM技術及PID算法,對四輪進行精準地速度、轉向及啟停控制,實驗表明此小車具有優越各種地形適應能力。In the traditional intelligent car drive circuit design,DC motor or stepping motor,motor power,energy consumption and other performance parameters are considered.The four DC motors with four wheels are controlled by STM32 embedded platform with arm Cortex M4 kernel.Based on the PWM technology and PID algorithm,the accurate ground speed,steering,and start-stop control of the four wheels are carried out.The experiment shows that the vehicle has the superior adaptability to all kinds of terrains.
標簽： stm32 智能小車 控制系統
上傳時間： 2022-04-02
上傳用戶：
以單片機控制A/D轉換器TLC549為例,對A/D轉換器的主要技術指標進行了分析研究,在Proteus平臺下,完成了A/D轉換電路的構建,采用器件工作時序方式進行程序編寫,借助仿真圖表、虛擬儀器等工具對A/D轉換的數據進行測量并對失調誤差、增益誤差、微分非線性、積分非線性和轉換時間等重要參數進行了詳細分析。結果表明:使用Proteus軟件可對A/D轉換過程進行定性分析,將抽象的A/D轉換器技術指標直觀化、形象化展現出來,有助于學生更好地理解A/D轉換過程。The main technical indicators of A/D converter were analyzed and studied with an example from A/D converter TLC2543 which is controlled by using SCM.It was completed the construction of the A/D converter circuit under the Proteus software.The programming based on the operation sequence of the chip is put forward.With the aid of the simulation tools such as virtual instrument,simulation charts provided by Proteus,the important parameters of circuit such as offset error,gain error,differential nonlinearity(DNL),integral nonlinearity (INL) and conversion time are analyzed detailedly.Simulation results show that the A/D conversion process can be qualitatively analyzed and visualized the abstract indicators of A/D.The system can help students better to understand the SCM conversion process.
標簽： proteus 單片機 模數轉換
上傳時間： 2022-04-04
上傳用戶：
為解決移相全橋電路驅動及相角控制問題,設計了一種數字控制的移相全橋驅動電路.以TPL521為光耦隔離、IR2110為柵極驅動芯片.由DSP產生PWM信號,經過光耦隔離和邏輯電路后送至IR2110進行相角控制.文章對IR2110驅動電路原理進行分析及參數進行設計,對TMS320F28335進行設置并給出部分代碼.實驗結果表明：通過TMS320F28335可產生的不同相角的PWM波形,滿足了移相全橋?qū)Σ煌嘟强刂频囊?In order to solve the problem of phase-shifted full-bridge circuit driving and phase angle control,a digitally controlled phaseshifted full-bridge driving circuit was designed. TPL521 optocoupler isolation,IR2110 gate driver chip. PWM signals are generated by the DSP and sent to the IR2110 for phase angle control after optocoupler isolation and logic circuits. This text carries on the analysis to the principle of IR2110 drive circuit and parameter design,set up and give out some code to TMS320F28335. The experimental results show that the PWM waveforms with different phase angles generated by TMS320F28335 can meet the requirements of phase-shifted full-bridge control for different phase angles.
上傳時間： 2022-05-03
上傳用戶：zhanglei193
Algebra, Topology, Differential Calculus, and Optimization Theory For Computer Science and Machine Learning一本數學大全書，由Jean Gallier and Jocelyn Quaintance合著。
標簽： 機器學習 數學
上傳時間： 2022-05-05
上傳用戶：默默
蟲蟲下載站版權所有 京ICP備2021023401號-1
