Integrating A/D converters have two characteristics incommon. First, as the name implies, their
上傳時間： 2013-04-24
上傳用戶：matlab
·詳細說明：MP3程序 采用c51編程 適用于任何環境 -MP3 procedure uses the c51 programming to be suitable for any environm文件列表: COMMON.C51 ..........\BYTE2CHAR.C ..........\COMMON.H ..........\COM
上傳時間： 2013-07-24
上傳用戶：tfyt
·JPEG2000 EBCOT算法源碼文件列表: .cdtproject .project common ......\hplx_coeffs.h ......\hplx_info.c ......\line_block_ifc.h ......\local_heap.h compress
上傳時間： 2013-05-21
上傳用戶：jiachuan666
關于 ‘‘地’’ 電路中參考點－零電位點，稱為地點。開關電源中的‘‘地’’：： 公共端 (common)(common)－輸出與輸入參考點。例如－PFCPFC與后繼變換器輸入端的公共端。 電路中的地 (ground(ground--GND)GND)－所有電路共用參考－點。如輔助電源與PFCPFC及DC/DCDC/DC公共端。 大地 (earth(earth--E)電網供電設備通常以大地EE作為零電位。三相輸配電三相中點接大地EE，同時引出中，線NN。 接地阻抗很小的大面積 ‘‘地’’稱為地平面(Ground plane(plane)。
上傳時間： 2013-04-24
上傳用戶：1079836864
·文件列表: mp3decode .........\common.c .........\common.h .........\decode.c .........\decode.h .........\huffman.c .........\huffman.h .........\la
上傳時間： 2013-04-24
上傳用戶：Pzj
nxp lpc23/24xx keil例程 通用文件
上傳時間： 2013-07-28
上傳用戶：shijiang
Abstract: Alexander Graham Bell patented twisted pair wires in 1881. We still use them today because they work so well. In addition we have the advantage ofincredible computer power within our world. Circuit simulators and filter design programs are available for little or no cost. We combine the twisted pair and lowpassfilters to produce spectacular rejection of radio frequency interference (RFI) and electromagnetic interference (EMI). We also illustrate use of a precision resistorarray to produce a customizable differential amplifier. The precision resistors set the gain and common mode rejection ratios, while we choose the frequencyresponse.
上傳時間： 2014-11-26
上傳用戶：Vici
The LT®6552 is a specialized dual-differencing 75MHzoperational amplifier ideal for rejecting common modenoise as a video line receiver. The input pairs are designedto operate with equal but opposite large-signal differencesand provide exceptional high frequency commonmode rejection (CMRR of 65dB at 10MHz), therebyforming an extremely versatile gain block structure thatminimizes component count in most situations. The dualinput pairs are free to take on independent common modelevels, while the two voltage differentials are summedinternally to form a net input signal.
上傳時間： 2014-12-23
上傳用戶：13691535575
Who has never experienced oscillations issues when using an operational amplifier? Opampsare often used in a simple voltage follower configuration. However, this is not the bestconfiguration in terms of capacitive loading and potential risk of oscillations.Capacitive loads have a big impact on the stability of operational amplifier-basedapplications. Several compensation methods exist to stabilize a standard op-amp. Thisapplication note describes the most common ones, which can be used in most cases.The general theory of each compensation method is explained, and based on this, specific
上傳時間： 2013-10-28
上傳用戶：chenbhdt
ANALOG INPUT BANDWIDTH is a measure of the frequencyat which the reconstructed output fundamental drops3 dB below its low frequency value for a full scale input. Thetest is performed with fIN equal to 100 kHz plus integer multiplesof fCLK. The input frequency at which the output is −3dB relative to the low frequency input signal is the full powerbandwidth.APERTURE JITTER is the variation in aperture delay fromsample to sample. Aperture jitter shows up as input noise.APERTURE DELAY See Sampling Delay.BOTTOM OFFSET is the difference between the input voltagethat just causes the output code to transition to the firstcode and the negative reference voltage. Bottom Offset isdefined as EOB = VZT–VRB, where VZT is the first code transitioninput voltage and VRB is the lower reference voltage.Note that this is different from the normal Zero Scale Error.CONVERSION LATENCY See PIPELINE DELAY.CONVERSION TIME is the time required for a completemeasurement by an analog-to-digital converter. Since theConversion Time does not include acquisition time, multiplexerset up time, or other elements of a complete conversioncycle, the conversion time may be less than theThroughput Time.DC COMMON-MODE ERROR is a specification which appliesto ADCs with differential inputs. It is the change in theoutput code that occurs when the analog voltages on the twoinputs are changed by an equal amount. It is usually expressed in LSBs.
上傳時間： 2013-11-12
上傳用戶：pans0ul
