Avalanche photodiodes (APDs) are widely utilized in laserbased fiberoptic systems to convert optical data intoelectrical form. The APD is usually packaged with a signalconditioning amplifier in a small module. An APD receivermodule and attendant circuitry appears in Figure 1. TheAPD module (figure right) contains the APD and a transimpedance(e.g., current-to-voltage) amplifier. An opticalport permits interfacing fiberoptic cable to the APD’sphotosensitive portion. The module’s compact constructionfacilitates a direct, low loss Connection between theAPD and the amplifier, necessary because of the extremelyhigh speed data rates involved
上傳時間： 2013-10-25
上傳用戶：brain kung
AVR32801: UC3A3 Schematic Checklist Features • Power circuit • Reset circuit • USB Connection • External bus interface • ABDAC sound DAC interface • JTAG and Nexus debug ports • Clocks and crystal oscillators • MMC, SD-card, SDHC, SDIO and CE-ATA interface 1 Introduction A good hardware design comes from a proper schematic. Since UC3A3 devices have a fair number of pins and functions, the schematic for these devices can be large and quite complex. This application note describes a common checklist which should be used when starting and reviewing the schematics for a UC3A3 design.
標簽： Schematic 32801 UC3A3 Chec
上傳時間： 2014-12-26
上傳用戶：DXM35
單片機作為一種微型計算機，其內部具有一定的存儲單元（8031除外），但由于其內部存儲單元及端口有限，很多情況下難以滿足實際需求。為此介紹一種新的擴展方法，將數據線與地址線合并使用，通過軟件控制的方法實現數據線與地址線功能的分時轉換，數據線不僅用于傳送數據信號，還可作為地址線、控制線，用于傳送地址信號和控制信號，從而實現單片機與存儲器件的有效連接。以單片機片外256KB數據存儲空間的擴展為例，通過該擴展方法，僅用10個I/O端口便可實現，與傳統的擴展方法相比，可節約8個I/O端口。 Abstract: As a micro-computer,the SCM internal memory has a certain units(except8031),but because of its internal storage units and the ports are limited,in many cases it can not meet the actual demand.So we introduced a new extension method,the data line and address lines combined through software-controlled approach to realize the time-conversion functions of data lines and address lines,so the data lines not only transmited data signals,but also served as address lines and control lines to transmit address signals and control signals,in order to achieve an effective Connection of microcontroller and memory chips.Take microcontroller chip with256KB of data storage space expansion as example,through this extension method,with only10I/O ports it was achieved,compared with the traditional extension methods,this method saves8I/O ports.
上傳時間： 2014-12-26
上傳用戶：adada
介紹一種基于單片機的多路溫度采集及監控系統，能夠測量6路溫度信號，具有計算機聯網功能，各測量點可以單獨監控和設置，可根據用戶的需求自動控制。測量溫度范圍為-10 ℃～200 ℃，控制方式采用模擬量調壓模式。該系統具有控制精度高、沖擊小等特點。 Abstract: A temperature collecting and surveillance-controlling system based on sing-chip microcomputer is introduced. It can measure 6 channel signal of the temperature,and it has a function of network Connection.The temperature measure points can be monitored and located, it can be controlled automatic according to user’s demand.The temperature range is -10℃ to 200℃.The model of control is adjustable voltage with simulation. It features high precision and little impact.
上傳時間： 2013-10-23
上傳用戶：bjgaofei
Stellaris(群星)單片機的片上FLASH編程(英) INFORMATION IN THIS DOCUMENT IS PROVIDED IN Connection WITH LUMINARY MICRO PRODUCTS. NO LICENSE,EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THISDOCUMENT. EXCEPT AS PROVIDED IN LUMINARY MICRO’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS,LUMINARY MICRO ASSUMES NO LIABILITY WHATSOEVER, AND LUMINARY MICRO DISCLAIMS ANY EXPRESS OR IMPLIEDWARRANTY, RELATING TO SALE AND/OR USE OF LUMINARY MICRO’S PRODUCTS INCLUDING LIABILITY OR WARRANTIESRELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHTOR OTHER INTELLECTUAL PROPERTY RIGHT. LUMINARY MICRO’S PRODUCTS ARE NOT INTENDED FOR USE IN MEDICAL,LIFE SAVING, OR LIFE-SUSTAINING APPLICATIONS.
上傳時間： 2013-10-22
上傳用戶：JamesB
Stellaris(群星)單片機加上32KB串行SRAM(英) INFORMATION IN THIS DOCUMENT IS PROVIDED IN Connection WITH LUMINARY MICRO PRODUCTS. NO LICENSE,EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THISDOCUMENT. EXCEPT AS PROVIDED IN LUMINARY MICRO’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS,LUMINARY MICRO ASSUMES NO LIABILITY WHATSOEVER, AND LUMINARY MICRO DISCLAIMS ANY EXPRESS OR IMPLIEDWARRANTY, RELATING TO SALE AND/OR USE OF LUMINARY MICRO’S PRODUCTS INCLUDING LIABILITY OR WARRANTIESRELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHTOR OTHER INTELLECTUAL PROPERTY RIGHT. LUMINARY MICRO’S PRODUCTS ARE NOT INTENDED FOR USE IN MEDICAL,LIFE SAVING, OR LIFE-SUSTAINING APPLICATIONS.
上傳時間： 2013-11-22
上傳用戶：lixqiang
The MAX3243E device consists of three line drivers, five line receivers, and a dual charge-pump circuit with±15-kV ESD (HBM and IEC61000-4-2, Air-Gap Discharge) and ±8-kV ESD (IEC61000-4-2, Contact Discharge)protection on serial-port Connection pins. The device meets the requirements of TIA/EIA-232-F and provides theelectrical interface between an asynchronous communication controller and the serial-port connector. Thiscombination of drivers and receivers matches that needed for the typical serial port used in an IBM PC/AT, orcompatible. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-Vsupply. In addition, the device includes an always-active noninverting output (ROUT2B), which allowsapplications using the ring indicator to transmit data while the device is powered down. The device operates atdata signaling rates up to 250 kbit/s and a maximum of 30-V/ms driver output slew rate.
標簽： MULTICHANNEL 5.5 TO RS
上傳時間： 2013-10-19
上傳用戶：ddddddd
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 MicrocontrollerCore. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementationof the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision1.1.This application note describes a demonstration program that has been written for the DK3200 hardwaredemonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to workwith the device, using the HID class as a ready-made device driver for the USB Connection.IN-APPLICATION-PROGRAMMING (IAP) AND IN-SYSTEM-PROGRAMMING (ISP)Since the μPSD contains two independent Flash memory arrays, the Micro Controller Unit (MCU) can executecode from one memory while erasing and programming the other. Product firmware updates in thefield can be reliably performed over any communication channel (such as CAN, Ethernet, UART, J1850)using this unique architecture. For In-Application-Programming (IAP), all code is updated through theMCU. The main advantage for the user is that the firmware can be updated remotely. The target applicationruns and takes care on its own program code and data memory.IAP is not the only method to program the firmware in μPSD devices. They can also be programmed usingIn-System-Programming (ISP). A IEEE1149.1-compliant JTAG interface is included on the μPSD. Withthis, the entire device can be rapidly programmed while soldered to the circuit board (Main Flash memory,Secondary Boot Flash memory, the PLD, and all configuration areas). This requires no MCU participation.The MCU is completely bypassed. So, the μPSD can be programmed or reprogrammed any time, anywhere, even when completely uncommitted.Both methods take place with the device in its normal hardware environment, soldered to a printed circuitboard. The IAP method cannot be used without previous use of ISP, because IAP utilizes a small amountof resident code to receive the service commands, and to perform the desired operations.
標簽： Demonstration 3200 USB for
上傳時間： 2014-02-27
上傳用戶：zhangzhenyu
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 Microcontroller Core. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementation of the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision 1.1.This application note describes a demonstration program that has been written for the DK3200 hardware demonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to work with the device, using the HID class as a ready-made device driver for the USB Connection.
上傳時間： 2014-04-03
上傳用戶：lizhizheng88
CAN與RS232轉換節點的設計與實現 介紹將CAN總線接口與RS232總線接口相互轉換的設計方法和2種總線電平轉換關系，實現CAN總線與各模塊的接口設計，制定了相應的軟硬件設計方案，并給出軟件設計流程圖以及部分硬件設計原理圖。為CAN總線與RS232總線互聯提供了一種方法，對CAN總線與RS232總線接口設備的互聯和廣泛應用的實現具有重要意義。關鍵詞：CAN總線；RS-232總線；串行通信Design and Realization of CAN and RS232 Transformation NodeZHOU Wei, CHENG Xiao-hong(Information Institute, Wuhan University of Technology, Wuhan 430070)【Abstract】This paper introduces one design method of the CAN bus interface and the RS232 bus interface interconversion, emphasizes two kindof bus level transformation relations, realizes the CAN bus and various modules Connection design, formulates the design proposal of correspondingsoftware and hardware, and gives the flow chart of software design as well as the partial schematic diagram of hardware design. It providesonemethod for the CAN bus and the RS232 bus interConnection, has the vital significance to widespread application realization of the CAN busand theRS232 bus interface equipment interConnection.【Key words】CAN bus; RS-232 bus; serial communication
上傳時間： 2013-11-04
上傳用戶：leesuper
