運放電路中的恒流源電路分析方法 普通鏡像恒流源、多集電極恒流源、高精度鏡像恒流源、高內阻恒流源和鏡像微恒流源電路，以及恒流源電路輸出電阻的計算等。 分析恒流源電路的方法是： （1）確定恒流源電路中的基準晶體管或場效應管； （2） 計算或確定基準電流； &nbbsp; （4）繪制恒流部分的交流通路，確定恒流源的內阻。 由于恒流源的內阻較大，計算恒流源內阻時不能忽略三極管集電極與發射極之間，或場效應管漏極與源極之間的動態電阻
上傳時間： 2013-10-09
上傳用戶：gxmm
在傳統正溫度系數電流基礎上,增加兩種不同材料的電阻以實現帶隙基準的二階溫度補償,采用具有反饋偏置的折疊共源共柵運算放大器,使得所設計的帶隙基準電路,具有較高的精度和溫度穩定性。
上傳時間： 2013-10-18
上傳用戶：604759954
介紹了一種基于Cortex-M3(STM32F103C8)芯片的高速度、低功耗、多功能數字可調共振源,以及系統的CPU部分、信號發生、濾波及放大部分及相應的軟件設計。
上傳時間： 2013-11-03
上傳用戶：liu999666
高的工作電壓高達100V N雙N溝道MOSFET同步驅動 The D810DCDC is a synchronous step-down switching regulator controller that can directly step-down voltages from up to 100V, making it ideal for telecom and automotive applications. The D810DCDC uses a constant on-time valley current control architecture to deliver very low duty cycles with accurate cycle-by-cycle current limit, without requiring a sense resistor. A precise internal reference provides 0.5% DC accuracy. A high bandwidth (25MHz) error amplifi er provides very fast line and load transient response. Large 1Ω gate drivers allow the D810DCDC to drive multiple MOSFETs for higher current applications. The operating frequency is selected by an external resistor and is compensated for variations in VIN and can also be synchronized to an external clock for switching-noise sensitive applications. Integrated bias control generates gate drive power from the input supply during start-up and when an output shortcircuit occurs, with the addition of a small external SOT23 MOSFET. When in regulation, power is derived from the output for higher effi ciency.
上傳時間： 2013-10-24
上傳用戶：wd450412225
在醫用電阻抗層析成像（Electrical Impedance Tomography）系統中電壓控制電流源的性能十分重要，大部分報道的電壓控電流源電路在低頻時有較高的輸出阻抗但是在高頻時性能大幅減弱。通過分析生物阻抗測量系統對電壓控制電流源的需求，同時回顧一些已有的電壓控制電流源電路，包括雙運放負反饋電路、跨導運算放大器、AD844，設計了一種基于AD8610的電壓控制電流源。并通過電路實驗驗證了此電壓控制電流源的性能，同時提出了改進方案。該電壓電流源不僅頻率和幅值可控、精度高，而且有較高的輸出阻抗。
標簽： 電阻抗 成像系統 電壓控制 電流源
上傳時間： 2013-11-05
上傳用戶：heart_2007
Multiple-voltage electronics systems often requirecomplex supply voltage tracking or sequencing, whichif not met, can result in system faults or even permanentfailures in the fi eld. The design diffi culties in meetingthese requirements are often compounded in distributedpowerarchitectures where point-of-load (POL) DC/DCconverters or linear regulators are scattered across PCboard space, sometimes on different board planes. Theproblem is that power supply circuitry is often the lastcircuitry to be designed into the board, and it must beshoehorned into whatever little board real estate is left.Often, a simple, drop-in, fl exible solution is needed tomeet these requirements.
上傳時間： 2013-10-08
上傳用戶：15071087253
交一直一交變頻器的中間直流環節如果是用大電容平波通常稱為電壓源型變頻器。如果分開來稱呼，則其后端逆變器部分叫電壓源逆變器(VSI)，產品GB和IEC標準也是這種稱呼。其前端整流部分對電網而言是— 個諧波源，也就叫電壓型諧波源。與此相對照，交一直一交變頻器的中間直流環節如果用大電感平波就分別稱為電流源型變頻器、電流源逆變器(CSD、電流源型諧波源。之所以要特別區分變頻器為電壓源和電流源兩大類是因為他們的交流輸入電流波形和變頻后輸出的交流電壓和交流電流的波形及性能都有很大的不同。
上傳時間： 2013-11-03
上傳用戶：xitai
In a recent discussion with a system designer, the requirementfor his power supply was to regulate 1.5Vand deliver up to 40A of current to a load that consistedof four FPGAs. This is up to 60W of power that must bedelivered in a small area with the lowest height profi lepossible to allow a steady fl ow of air for cooling. Thepower supply had to be surface mountable and operateat high enough effi ciency to minimize heat dissipation.He also demanded the simplest possible solution so histime could be dedicated to the more complex tasks. Asidefrom precise electrical performance, this solution had toremovethe heat generated during DC to DC conversionquickly so that the circuit and the ICs in the vicinity do notoverheat. Such a solution requires an innovative designto meet these criteria:
上傳時間： 2013-11-24
上傳用戶：defghi010
The LTM8020, LTM8021, LTM8022 and LTM8023 μModule®regulators are complete easy-to-use encapsulated stepdownDC/DC regulators intended to take the pain and aggravationout of implementing a switching power supplyonto a system board. With a μModule regulator, you onlyneed an input cap, output cap and one or two resistorsto complete the design. As one might imagine, this highlevel of integration greatly simplifi es the task of printedcircuit board design, reducing the effort to four categories:component footprint generation, component placement,routing the nets, and thermal vias.
上傳時間： 2014-01-18
上傳用戶：laomv123
為解決直流逆變交流的問題，有效地利用能源，讓電源輸出最大功率，設計了高性能的基于IR2101最大功率跟蹤逆變器，并以SPMC75F2413A單片機作為主控制器。高電壓、高速功率的MOSFET或IGBT驅動器IR2101采用高度集成的電平轉換技術，同時上管采用外部自舉電容上電，能夠穩定高效地驅動MOS管。該逆變器可以實現DC/AC的轉換，最大功率點的跟蹤等功能。實際測試結果表明，該逆變器系統具有跟蹤能力強，穩定性高，反應靈敏等特點，該逆變器不僅可應用于普通的電源逆變系統，而且可應用于光伏并網發電的逆變系統，具有廣泛的市場前景。 Abstract: To solve the problem of DC-AC inverter， and to utilize solar energy more efficiently， the design of maximum power point tracking inverter based on IR2101 was achieved with a high-performance， which can make the system output power maximum. SPMC75F2413A was adopted as main controller. IR2101 is a high voltage， high speed power MOSFET and IGBT driver. It adopted highly integrated voltage level transforming technology， and an external bootstrap capacitor was used， which could drive MOS tube efficiently and stably. Many functions are achieved in the system， such as DC/AC conversion， maximun power point tracking， etc. The actual test result shows that the inverter system has characteristics of strong tracking ability， high stability and reacting quickly. The design can not only be used in ordinary power inverter system， but also be used in photovoltaic power inverter system. The design has certain marketing prospects
上傳時間： 2013-11-17
上傳用戶：lliuhhui
蟲蟲下載站版權所有 京ICP備2021023401號-1
