Full bridge inerter used in power electronics lab
標簽: electronics inerter bridge power
上傳時間: 2013-12-09
上傳用戶:cuiyashuo
隔離升壓DC-DC變換器在電動汽車、儲能系統、可再生能源發電以及超導儲能系統等領域有廣闊的應用前景。本文以隔離升壓全橋變換器(Isolated Boost Full Bridge Converter,簡稱IBFBC)為研究對象,針對隔離升壓型變換器的拓撲結構、起動問題、隔離變壓器漏感問題、軟開關問題和輸入電感磁復位問題等進行了系統深入的研究,解決了這一類拓撲所共有技術問題。 提出了隔離升壓DC-DC變換器拓撲族,分析比較了各種拓撲的特點,確定了以IBFBC為研究對象。對IBFBC進行了詳細的穩態分析和小信號建模分析,為其分析、設計和搭建實驗平臺提供了電路理論基礎。 理論上分析了IBFBC起動時存在電流沖擊的原因。提出了二種數字化軟起動方案,該方案對主電路進行了改造,利用DSP能靈活產生PWM波的特點采用了新的控制策略,成功實現了該系統的軟起動。 理論上分析了IBFBC隔離變壓器漏感引起功率開關管關斷電壓尖峰的原因,采用了有源箝位的方法,有效的解決電壓尖峰問題。提出了帶有源箝位IBFBC的九種PWM控制策略,提出了一種控制型軟PWM方法,在不增加主電路元器件的基礎上,通過控制PWM的發生方法,實現了有源箝位功率開關管和橋臂功率開關管的零電壓開通。 從理論上分析了IBFBC輸入電感磁復位問題。在正常停機時提出了一種數字化軟停止的方法,控制變換器由Boost工作狀態逐漸過渡到Buck工作狀態,讓輸入電感存儲的能量逐漸釋放掉,最后停止工作。對于故障保護停機,采用了繞組磁復位的方法,把輸入電感設計成反激式變換器形式,突然停機時,電感中存儲的能量通過反激式繞組釋放到輸出端,這樣保護了變換器不會損壞。 給出了主電路關鍵器件參數的設計方法,設計了以DSP-TMS320F2407為核心的數字控制單元,編寫了DSP控制程序和CPLD邏輯處理程序。研制了一臺輸出功率5KW,輸入電壓直流24V,輸出電壓直流300V的IBFBC,通過全面的性能實驗驗證了理論分析和仿真結果。 本文立足于IBFBC的關鍵技術要求,并充分考慮工程應用中的實際因素,進行了理論分析和實驗研究,為實際系統方案設計提供理論依據,并已經在實際應用中得到驗證。
上傳時間: 2013-04-24
上傳用戶:lifevast
近些年來,隨著電力電子技術的發展,電力電子系統集成受到越來越多的關注,其中標準化模塊的串并聯技術成為研究熱點之一。輸入并聯輸出串聯型(Input-Parallel and Output-Series,IPOS)組合變換器適用于大功率高輸出電壓的場合。 要保證IPOS組合變換器正常工作,必須保證其各模塊的輸出電壓均衡。本文首先揭示了IPOS組合變換器中每個模塊輸入電流均分和輸出電壓均分之間的關系,在此基礎上提出一種輸出均壓控制方案,該方案對系統輸出電壓調節沒有影響。選擇移相控制全橋(FULL-BRIDGE,FB)變換器作為基本模塊,對n個全橋模塊組成的IPOS組合變換器建立小信號數學模型,推導出采用輸出均壓控制方案的IPOS-FB系統的數學模型,該模型證明各模塊輸出均壓閉環不影響系統輸出電壓閉環的調節,給出了模塊輸出均壓閉環和系統輸出電壓閉環的補償網絡參數設計。對于IPOS組合變換器,采用交錯控制,由于電流紋波抵消效應,輸入濾波電容容量可大大減小;由于電壓紋波抵消作用,在相同的系統輸出電壓紋波下,各模塊的輸出濾波電容可大大減小,由此可以提高變換器的功率密度。 根據所提出的輸出均壓控制策略,在實驗室研制了一臺由兩個1kW全橋模塊組成的IPOS-FB原理樣機,每個模塊輸入電壓為270V,輸出電壓為180V。并進行了仿真和實驗驗證,結果均表明本控制方案是正確有效的。
上傳時間: 2013-06-17
上傳用戶:cwyd0822
The L298 is an integratedmonolithic circuit in a 15- lead Multiwatt and PowerSO20 packages. It is a
標簽: FULL-BRIDGE DRIVER l298 DUAL
上傳時間: 2013-08-03
上傳用戶:wendy15
Piezoelectric motors are used in digital cameras for autofocus,zooming and optical image stabilization. Theyare relatively small, lightweight and effi cient, but theyalso require a complicated driving scheme. Traditionally,this challenge has been met with the use ofseparatecircuits, including a step-up converter and an oversizedgeneric FULL-BRIDGE drive IC. The resulting high componentcount and large board space are especially problematicin the design of cameras for ever shrinking cell phones.The LT®3572 solves these problems by combining astep-up regulator and a dual FULL-BRIDGE driver in a 4mm× 4mm QFN package. Figure 1 shows a typical LT3572Piezo motor drive circuit. A step-up converter is usedto generate 30V from a low voltage power source suchas a Li-Ion battery or any input power source within thepart’s wide input voltage range of 2.7V to 10V. The highoutput voltage of the step-up converter, adjustable upto 40V, is available for the drivers at the VOUT pin. Thedrivers operate in a FULL-BRIDGE fashion, where the OUTAand OUTB pins are the same polarity as the PWMA andPWMB pins, respectively, and the OUTA and OUTB pinsare inverted from PWMA and PWMB, respectively. Thestep-up converter and both Piezo drivers have their ownshutdown control. Figure 2 shows a typical layout
上傳時間: 2013-11-18
上傳用戶:hulee
近距電能傳輸——高效安全近距電能傳輸一般基于電磁感應原理進行。在此技術基礎上,當接收器鄰近發射器時才會進行電能傳輸。電磁感應技術的歷史長達百年,多年米一直應用于各類電子產品中—如此普及全因其簡單、高效以及安全技術概覽以下將為你簡要介紹無線電能傳輸技術。System Overview(Communication)Receiver sends messagesTo provide control information to the transmitterBy load modulation on the power signaTransmitter receives messagesTo receive control information frorn the recelverBy de-modulation of the reflected loadPower Pick Up( Receiver)Secondary coil (L Serial resonance capacitor (C) for efficient power transfer Parallel resonance capacitor(C, )for detection purposes Rectifier: full bridge(diode, or switched)+ capacitor Output switch for(dis)connecting the loadReceiver modulates load by Switching modulation resistor(R,n),or Switching modulation capacitor(Ca)Transmitter de-modulates reflected load by Sensing pnmary coil curent (p)and/o Sensing primary coil voltage (V,
上傳時間: 2022-03-31
上傳用戶:
為解決移相全橋電路驅動及相角控制問題,設計了一種數字控制的移相全橋驅動電路.以TPL521為光耦隔離、IR2110為柵極驅動芯片.由DSP產生PWM信號,經過光耦隔離和邏輯電路后送至IR2110進行相角控制.文章對IR2110驅動電路原理進行分析及參數進行設計,對TMS320F28335進行設置并給出部分代碼.實驗結果表明:通過TMS320F28335可產生的不同相角的PWM波形,滿足了移相全橋對不同相角控制的要求.In order to solve the problem of phase-shifted FULL-BRIDGE circuit driving and phase angle control,a digitally controlled phaseshifted FULL-BRIDGE driving circuit was designed. TPL521 optocoupler isolation,IR2110 gate driver chip. PWM signals are generated by the DSP and sent to the IR2110 for phase angle control after optocoupler isolation and logic circuits. This text carries on the analysis to the principle of IR2110 drive circuit and parameter design,set up and give out some code to TMS320F28335. The experimental results show that the PWM waveforms with different phase angles generated by TMS320F28335 can meet the requirements of phase-shifted FULL-BRIDGE control for different phase angles.
上傳時間: 2022-05-03
上傳用戶:zhanglei193
eSP268 is a USB 2.0 High-speed (HS) and Full-speed (FS) compatible PC cameracontro
標簽: Controller Camera Bridge eSP
上傳時間: 2013-06-06
上傳用戶:ice_qi
單片機仿真軟件,單片機開發仿真環境keil.c51.v706.Full。
上傳時間: 2014-12-31
上傳用戶:lo25643
單片機仿真軟件,單片機開發仿真環境keil.c51.v706.Full。
上傳時間: 2013-10-13
上傳用戶:ca05991270