The PCA9671 provides general purpose remote I/O expansion for most microcontrollerFamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plus(Fm+) family.The PCA9671 is a drop in upgrade for the PCF8575 providing higher I2C-bus speeds(1 MHz versus 400 kHz) so that the output can support PWM dimming of LEDs, higherI2C-bus drive (30 mA versus 3 mA) so that many more devices can be on the bus withoutthe need for bus buffers, higher total package sink capacity (400 mA versus 100 mA) thatsupports having all 25 mA LEDs on at the same time and more device addresses (64versus 8) to allow many more devices on the bus without address conflicts.
上傳時間： 2013-10-12
上傳用戶：laomv123
The PCA9672 provides general purpose remote I/O expansion for most microcontrollerFamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plusfamily.The PCA9672 is a drop-in upgrade for the PCF8574 providing higher Fast-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all LEDs on at the same time and moredevice addresses (16 versus 8) are available to allow many more devices on the buswithout address conflicts.
上傳時間： 2013-10-23
上傳用戶：jasonheung
The PCA9673 provides general purpose remote I/O expansion for most microcontrollerFamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plusfamily.The PCA9673 is a drop in upgrade for the PCF8575 providing higher Fast-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(400 mA versus 100 mA) that supports having all 25 mA LEDs on at the same time andmore device addresses (16 versus 8) are available to allow many more devices on the buswithout address conflicts.
上傳時間： 2013-10-29
上傳用戶：wkchong
This application note describes how to implement the Bus LVDS (BLVDS) interface in the supported Altera ® device Families for high-performance multipoint applications. This application note also shows the performance analysis of a multipoint application with the Cyclone III BLVDS example.
標簽： Implementing LVDS 522 Bus
上傳時間： 2013-11-10
上傳用戶：frank1234
This application note describes how the existing dual-port block memories in the Spartan™-IIand Virtex™ Families can be used as Quad-Port memories. This essentially involves a dataaccess time (halved) versus functionality (doubled) trade-off. The overall bandwidth of the blockmemory in terms of bits per second will remain the same.
上傳時間： 2013-11-08
上傳用戶：lou45566
Xilinx FPGAs require at least two power supplies: VCCINTfor core circuitry and VCCO for I/O interface. For the latestXilinx FPGAs, including Virtex-II Pro, Virtex-II and Spartan-3, a third auxiliary supply, VCCAUX may be needed. Inmost cases, VCCAUX can share a power supply with VCCO.The core voltages, VCCINT, for most Xilinx FPGAs, rangefrom 1.2V to 2.5V. Some mature products have 3V, 3.3Vor 5V core voltages. Table 1 shows the core voltagerequirement for most of the FPGA device Families. TypicalI/O voltages (VCCO) vary from 1.2V to 3.3V. The auxiliaryvoltage VCCAUX is 2.5V for Virtex-II Pro and Spartan-3, andis 3.3V for Virtex-II.
上傳時間： 2013-10-22
上傳用戶：liu999666
This application note describes how to implement the Bus LVDS (BLVDS) interface in the supported Altera ® device Families for high-performance multipoint applications. This application note also shows the performance analysis of a multipoint application with the Cyclone III BLVDS example.
標簽： Implementing LVDS 522 Bus
上傳時間： 2013-10-26
上傳用戶：蘇蘇蘇蘇
This application note describes how the existing dual-port block memories in the Spartan™-IIand Virtex™ Families can be used as Quad-Port memories. This essentially involves a dataaccess time (halved) versus functionality (doubled) trade-off. The overall bandwidth of the blockmemory in terms of bits per second will remain the same.
上傳時間： 2014-01-24
上傳用戶：15527161163
Xilinx FPGAs require at least two power supplies: VCCINTfor core circuitry and VCCO for I/O interface. For the latestXilinx FPGAs, including Virtex-II Pro, Virtex-II and Spartan-3, a third auxiliary supply, VCCAUX may be needed. Inmost cases, VCCAUX can share a power supply with VCCO.The core voltages, VCCINT, for most Xilinx FPGAs, rangefrom 1.2V to 2.5V. Some mature products have 3V, 3.3Vor 5V core voltages. Table 1 shows the core voltagerequirement for most of the FPGA device Families. TypicalI/O voltages (VCCO) vary from 1.2V to 3.3V. The auxiliaryvoltage VCCAUX is 2.5V for Virtex-II Pro and Spartan-3, andis 3.3V for Virtex-II.
上傳時間： 2013-10-22
上傳用戶：aeiouetla
PCI設計指南The Xilinx LogiCORE PCI interface is a fully verified, pre-implemented PCI Bus interface. This interface is available in 32-bit and 64- bit versions, with support for multiple Xilinx FPGA device Families. It is designed to support both Verilog-HDL and VHDL. The design examples in this book are provided in Verilog.
標簽： interface PCI pre-implemented LogiCORE
上傳時間： 2016-04-03
上傳用戶：清風冷雨
