為解決我國水位監測野外條件下長期無人看守的問題，研制開發了基于MSP430單片機的智能水位計。從其組成到各功能分別進行了詳細的介紹，該智能水位計不僅實現了水位數據的實時監測、記錄和定期采集等多種工作模式，而且提高了水位監測精度，實現了水位監測的智能化。 Abstract: In order to solve the problems of long-term unmanned observation in the field water monitoring，an intelligence water-level meter based on MSP430 is developed composition and every function moduce of the water level meter was introduced in detail. It not only realizes water level data collection and storage， regularly gathering and so on， but also improves the water-level precision ， finally realizes the intelligence.
上傳時間： 2013-11-17
上傳用戶：417313137
針對眾多低成本數據采集需求，采用帶有片上USB控制器和D/A轉換器的混合信號微處理器C8051F340，設計了一款可通過USB接口和LabVIEW圖形用戶界面實現與PC機聯機的數據采集器，同時借助系統的SD卡存儲獨立實現現場長時間采集數據。該數據采集器成本低，結構簡單，體積小，已成功用于工業現場。 Abstract: Aiming at the need of low cost data acquisition, a data acquisition device is designed based on C8051F340 which is a mixed-signal microcontroller and integrates USB controller and A/D controller on a chip.The data acquisition device which can combine with PC by USB interface and LabVIEW graphical user interface,can realize data acquisition. At the same time,it can be solely run a long time in virtue of SD card in field.The date aequisition device features low cost,simple structure and little sharp, and it has been used in industry field.
上傳時間： 2014-05-31
上傳用戶：1109003457
為解決輸油管道溫度壓力參數實時監測的問題，設計了以C8051F930單片機作為控制核心的超低功耗輸油管道溫度壓力遠程監測系統。現場儀表使用高精度電橋采集數據，通過433 MHz短距離無線通信網絡與遠程終端RTU進行通信，RTU通過GPRS網絡與PC上位機進行遠程數據傳輸，在上位機中實現數據存儲和圖形化界面顯示，從而實現輸油管道溫度壓力參數的實時監測和異常報警。經實驗證明，該系統的12位數據采集精度滿足設計要求，漏碼率小于1%，正常工作時間超過5個月，能實時有效地監測輸油管道的溫度壓力參數，節省大量人工成本，有效預防管道參數異常造成的經濟損失和環境污染。 Abstract: In order to solve the problems on real-time monitoring of pipeline temperature and pressure parameters， the ultra-low power remote pipeline temperature and pressure monitoring system was designed by using the single chip processor C8051F930 as the control core. The high-precision electric bridge was used in field instruments for data collection， the 433MHz short-range wireless communication network was used to make communication between field instrument and RTU， the GPRS was used by the RTU to transmit data to the PC host computer， and the data was stored and displayed in the PC host computer， so the real-time monitoring and exception alerts of pipeline temperature and pressure parameters were achieved. The experiment proves that the system of which error rate is less than 1% over five months working with the 12-bit data acquisition accuracy can effectively monitor the pipeline temperature and pressure parameters in real time， it saves a lot of labor costs and effectively prevents environmental pollution and economic losses caused by abnormal channel parameters.
上傳時間： 2013-11-07
上傳用戶：cuibaigao
介紹了一種基于MSP430系列單片機和ADXL203加速度傳感器的數字式傾角儀，它不僅可以實現水平度檢測，而且可以測量00～3600范圍內的任意傾角，分辨率可達O．1。。此外，由于該傾角儀輸出為數字結果，因此它也可以與其他的數字設備結合起來，組合成一個功能更加強大的儀器。該數字傾角儀可廣泛應用于建筑、機械、道路、橋梁、石油、煤礦和地質勘探等各種需要測量重力參考系下傾角的場合。關鍵詞：MSP430F133單片機；力敏傳感器；ADXL203加速度計；角度測量 Abstract：This paper presents a new style digital inclinometer which is developed on the basis of the MSP430F133 MCU and the ADXL203 dual axis aeeelerometer．This inclinometer not only can test levelness，but also can measure any angle between 0。and 360。with an accuracy of 0．1 O．In addition，its output is a digital result，which makes it possible to integrate itself with other digital devices to form a more functional unit．This inclinometer can be widely used in any construction site，oil field，coal-mine or geologic survey and SO on where it will provide the working people with convenience to measure any angles．Key words：MSP430F133 MCU；force sensor；ADXL203 accelerometer；angle measurement
上傳時間： 2013-11-14
上傳用戶：lizhizheng88
匯編器在微處理器的驗證和應用中舉足輕重，如何設計通用的匯編器一直是研究的熱點之一。本文提出了一種開放式的匯編器系統設計思想，在匯編語言與機器語言間插入中間代碼CMDL（code mapping description language）語言，打破匯編語言與機器語言的直接映射關系，由此建立起一套描述匯編語言與機器語言的開放式映射體系。基于此開放式映射體系開發了一套匯編器系統，具有較高層次上的通用性和可移植性。【關鍵詞】指令集，CMDL，匯編器，開放式 Design of Retargetable Assembler System Liu Ling Feng Wen Nan Wang Ying Chun Jiang An Ping Ji Li Jiu IME of Peking University, 100871【摘要】An assembler plays a very important role in the field of microprocessor verifications and applications, thus how to build a retargetable assembler system has been a hotspot in this field for long time. This paper presents a new method about the retargetable assembler system design.It provides a kind of language CMDL, code mapping description language. During the process of assembling, assembler languages are firstly translated to CMDL, and then mapped to the machine codes. In an other word, CMDL is inserted between assembler languages and machine codes during the translation procedure. As a medium code, CMDL has a lot of features, such as high extraction, strong descript capabilities. It can describe almost all attributes of assembler languages. By breaking the direct mapping relationship between assembler languages and machine codes, the complexities of machine codes are hided to the users, therefore, the new retargetable assembler system has higher retargetable level by converting the mapping from assembler languages and machine codes to assembler languages and CMDL, and implementationof it becomes easier. Based on the new mapping system structure, a retargetable assemblersystem is developed. It proved the whole system has good retargetability and implantability.【關鍵詞】instruction set, symbol table, assembler, lexical analysis, retargetability
上傳時間： 2013-10-10
上傳用戶：meiguiweishi
基于LabVIEW和單片機的空調溫度場測量系統的研究:室內溫度是空調系統舒適性的重要指標,對其及時、準確地測量顯得非常重要。介紹單片機AT89C51 和數字式、單總線型溫度傳感器DS18B20 組成矩形測量網絡采集空調室內40 點溫度,LabVIEW作為開發平臺,二者之間通過串口實現數據通信,利用LabVIEW強大的數據處理和顯示功能對采集的空調溫度場數據進行實時處理、分析和顯示,詳細介紹了系統的硬件結構和軟件模塊的設計方案。關鍵詞:單片機;DS18B20 ;LabVIEW;串行通信 Abstract : Temperature is a very important criterion of air condition system′s comfort , so it is very significant to measure it accurately and real timely. This paper int roduces a data acquisition system of measuring 40 point s temperature for air condition room based on single wire digital sensor DS18B20 and microcont roller AT89C51 which are composed of rectangle measuring meshwork. The data communication between LabVIEW and microcont roller is executed via serial port ,and the temperature field data of air condition room are processed analyzed and displayed on LabVIEW. The hardware and software modules are also given in detail.Keywords : single chip ;DS18B20 ;LabVIEW; serial communication
上傳時間： 2014-05-05
上傳用戶：KSLYZ
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 MicrocontrollerCore. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementationof the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision1.1.This application note describes a demonstration program that has been written for the DK3200 hardwaredemonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to workwith the device, using the HID class as a ready-made device driver for the USB connection.IN-APPLICATION-PROGRAMMING (IAP) AND IN-SYSTEM-PROGRAMMING (ISP)Since the μPSD contains two independent Flash memory arrays, the Micro Controller Unit (MCU) can executecode from one memory while erasing and programming the other. Product firmware updates in thefield can be reliably performed over any communication channel (such as CAN, Ethernet, UART, J1850)using this unique architecture. For In-Application-Programming (IAP), all code is updated through theMCU. The main advantage for the user is that the firmware can be updated remotely. The target applicationruns and takes care on its own program code and data memory.IAP is not the only method to program the firmware in μPSD devices. They can also be programmed usingIn-System-Programming (ISP). A IEEE1149.1-compliant JTAG interface is included on the μPSD. Withthis, the entire device can be rapidly programmed while soldered to the circuit board (Main Flash memory,Secondary Boot Flash memory, the PLD, and all configuration areas). This requires no MCU participation.The MCU is completely bypassed. So, the μPSD can be programmed or reprogrammed any time, anywhere, even when completely uncommitted.Both methods take place with the device in its normal hardware environment, soldered to a printed circuitboard. The IAP method cannot be used without previous use of ISP, because IAP utilizes a small amountof resident code to receive the service commands, and to perform the desired operations.
標簽： Demonstration 3200 USB for
上傳時間： 2014-02-27
上傳用戶：zhangzhenyu
為了擴大監控范圍，提高資源利用率，降低系統成本，提出了一種多通道視頻切換的解決方案。首先從視頻信號分離出行場信號，然后根據行場信號由DSP和FPGA產生控制信號，控制多路視頻通道之間的切換，從而實現讓一個視頻處理器同時監控不同場景。實驗結果表明，該方案可以在視頻監控告警系統中穩定、可靠地實現視頻通道的切換。 Abstract: To expand the scope of monitoring， improve resource utilization， reduce system cost， a multiple video channels signal switching method is pointed out in this paper. First， horizontal sync signal and field sync signal from the video signal are separated， then control signal according to the sync signal by DSP and FPGA is generated to control the switching between multiple video channels. Thus， it achieves to make a video processor to monitor different place. Experimental results show that the method can realize video channel switching reliably， and is applied in the video monitoring warning system successfully.
上傳時間： 2013-11-09
上傳用戶：不懂夜的黑
摘 要 瞬態仿真領域的許多工作需要獲得可視化數據, 仿真電路不能將輸出參數繪制成圖形時研究工作將受到很大影響. 而權威電路仿真軟件PSpice 在這個方面不盡如人意. 本文提出了一種有效的解決辦法: 通過MATLAB 編程搭建一個PSpice 與MATLAB 的數據接口,使PSpice輸出數據文件可以導入到MATLAB中繪制圖形. 這令我們能夠很方便地獲得數據的規律以有效地分析仿真結果, 這項技術對于教學和工程實踐都有比較實際的幫助.關鍵詞: 瞬態仿真 仿真程序 PSpice MATLAB 可視化數據The Data Transfer from Pspice to MATLABWu hao Ning yuanzhong Liang yingAbstract Many works in the area of transient simulation has shown how a emulator such asPSpice can be interfaced to an control analysis package such as MATLAB to get viewdata. Thepaper describes how such interfaces can be made using the MATLAB programming. The platformas a typical platform will solve the problem that PSpice software sometimes can not draw the datato a picture. It can make us find the rule from numerous data very expediently, so we can analyzethe outcome of the simulation. And it also can be used in the field of education.Keywords Transient Simulation Emulator PSpice MATLAB Viewdata1 引言科學研究和工程應用常需要進行電路仿真 PSpice可進行直流 交流 瞬態等基本電路特性分析 也可進行蒙托卡諾 MC 統計分析 最壞情況 Wcase 分析 優化設計等復雜電路特性分析 它是國際上仿真電路的權威軟件 而MATLAB的主要特點有 高效方便的矩陣和數組運算 編程效率高 結構化面向對象 方便的繪圖功能 用戶使用方便 工具箱功能強大 兩者各有著重點 兩種軟件結合應用 對研究工作有很重要的意義香港理工大學Y. S. LEE 等人首先將PSpice和MATLAB結合 開發了電力電子電路優化用的CAD 程序MATSPICE[6] 將兩者相結合的關鍵在于 如何用MATLAB 獲取PSpice的仿真數據 對此參考文獻 6 里沒有詳細敘述 本文著重說明用MATLAB 讀取PSpice仿真數據的具體方法本論文利用MATLAB對PSpice仿真出的數據處理繪制出后者無法得到或是效果不好的仿真圖形 下面就兩者結合使用的例子 進行具體說明
上傳時間： 2013-10-20
上傳用戶：wuchunzhong
Abstract: There are many things to consider when designing a power supply for a field-programmablegate array (FPGA). These include (but are not limited to) the high number of voltage rails, and thediffering requirements for both sequencing/tracking and the voltage ripple limits. This application noteexplains these and other power-supply considerations that an engineer must think through whendesigning a power supply for an FPGA.
上傳時間： 2013-11-10
上傳用戶：iswlkje
