Ink Blotting One method for escaping from a maze is via ‘ink-blotting’. In this method your starting square is marked with the number ‘1’. All free, valid squares north, south, east and west around the number ‘1‘ are marked with a number ‘2’. In the next step, all free, valid squares around the two are marked with a ‘3’ and the process is repeated iteratively until : The exit is found (a free square other than the starting position is reached on the very edge of the maze), or, No more free squares are available, and hence no exit is possible.
標簽： method ink-blotting Blotting escaping
上傳時間： 2014-12-03
上傳用戶：123啊
介紹了viterbi譯碼器的編解碼器的設計，包括decoder.v,encoder.v.control.v,ram.v等，壓縮 包里面有pdf說明
上傳時間： 2013-12-20
上傳用戶：zhichenglu
Ideal for large low power (nanoWatt) and connectivity applications that benefit from the availability of four serial ports: double synchronous serial ports (I² C™ and SPI™ ) and double asynchronous (LIN capable) serial ports. Large amounts of RAM memory for buffering and FLASH program memory make it ideal for instrumentation panels, TCP/IP enabled embedded applications as well as metering and industrial control and monitoring applications. While operating up to 40 MHz, it is also backward software and hardware compatible with the PIC18F8720.
標簽： connectivity applications availabilit nanoWatt
上傳時間： 2016-02-04
上傳用戶：CHINA526
在使用單片機作為控制cpu時，請稍作簡化，具體的PID參數必須由具體對象通過實驗確定。由于單片機的處理速度和ram資源的限制，一般不采用浮點數運算，而將所有參數全部用整數，運算到最后再除以一個2的N次方數據（相當于移位），作類似定點數運算，可大大提高運算速度，根據控制精度的不同要求，當精度要求很高時，注意保留移位引起的“余數”，做好余數補償。這個程序只是一般常用pid算法的基本架構，沒有包含輸入輸出處理部分。
上傳時間： 2016-02-05
上傳用戶：1109003457
FIFO電路(first in，first out)，內部藏有１６ｂｉｔ×１６ｗｏｒｄ的Dual port RAM，依次讀出已經寫入的數據。因為不存在Address輸入，所以請自行設計內藏的讀寫指針。由FIFO電路輸出的EF信號(表示RAM內部的數據為空)和FF信號(表示RAM內部的數據為滿)來表示RAM內部的狀態，并且控制FIFO的輸入信號WEN(寫使能)和REN(讀使能)。以及為了更好得控制FIFO電路，AEF(表示RAM內部的數據即將空)信號也同時輸出。
上傳時間： 2016-02-06
上傳用戶：zhoujunzhen
μC/OS-II Goals Probably the most important goal of μC/OS-II was to make it backward compatible with μC/OS (at least from an application’s standpoint). A μC/OS port might need to be modified to work with μC/OS-II but at least, the application code should require only minor changes (if any). Also, because μC/OS-II is based on the same core as μC/OS, it is just as reliable. I added conditional compilation to allow you to further reduce the amount of RAM (i.e. data space) needed by μC/OS-II. This is especially useful when you have resource limited products. I also added the feature described in the previous section and cleaned up the code. Where the book is concerned, I wanted to clarify some of the concepts described in the first edition and provide additional explanations about how μC/OS-II works. I had numerous requests about doing a chapter on how to port μC/OS and thus, such a chapter has been included in this book for μC/OS-II.
標簽： OS-II compatible important Probably
上傳時間： 2013-12-02
上傳用戶：jkhjkh1982
vc開發PDA程序，Free for friends
上傳時間： 2014-01-12
上傳用戶：shanml
DSP2812的直流斬波調速程序，已經做出了實物，能成功的燒寫到了FLASH了用CCS2000調試用不同的CMD文件在RAM中運行或在FLASH中運行
上傳時間： 2016-02-26
上傳用戶：gououo
#include"c1.h" typedef int ElemType #include"c2-2.h" #include"bo2-4.cpp" void MergeList_CL(LinkList &La,LinkList Lb) { LinkList p=Lb->next Lb->next=La->next La->next=p->next free(p) La=Lb }
標簽： include MergeList_C ElemType typedef
上傳時間： 2016-03-03
上傳用戶：rishian
S3C2410的ADS工程，有內存映射，可在RAM中調試中斷
上傳時間： 2014-01-02
上傳用戶：佳期如夢
