<delect id="i6scc"></delect> Agilent 34401A Service Guide.pdfIEC Measurement Category II includes electrical devices connected to mains at an outlet on a branch circuit. Such devices include most small appliances, test equipment, and other devices that plug into a branch outlet or socket. The 34401A may be used to make measurements with the HI and LO inputs connected to mains in such devices, or to the branch outlet itself (up to 300 VAC). However, the 34401A may not be used with its HI and LO inputs connected to mains in permanently installed electrical devices such as the main circuit-breaker panel, sub-panel disconnect boxes, or permanently wired motors. Such devices and circuits are subject to overvoltages that may exceed the protection limits of the 34401A. Note: Voltages above 300 VAC may be measured only in circuits that are isolated from mains. However, transient overvoltages are also present on circuits that are isolated from mains. The Agilent 34401A are designed to safely withstand occasional transient overvoltages up to 2500 Vpk. Do not use this equipment to measure circuits where transient overvoltages could exceed this level. Additional Notices Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC This product complies with the WEEE Directive (2002/96/EC) marking requirement. The affixed product label (see below) indicates that you must not discard this electrical/electronic product in domestic household waste. Product Category: With reference to the equipment types in the WEEE directive Annex 1, this product is classified as a "Monitoring and Control instrumentation" product. Do not dispose in domestic household waste. To return unwanted products, contact your local Agilent office, or see www.agilent.com/environment/product for more information. Agilent 34138A Test Lead Set The Agilent 34401A is compatible with the Agilent 34138A Test Lead Set described below. Test Lead Ratings Test Leads - 1000V, 15A Fine Tip Probe Attachments - 300V, 3A Mini Grabber Attachment - 300V, 3A SMT Grabber Attachments - 300V, 3A Operation The Fine Tip, Mini Grabber, and SMT Grabber attachments plug onto the probe end of the Test Leads. Maintenance If any portion of the Test Lead Set is worn or damaged, do not use. Replace with a new Agilent 3413
標簽： agilent
上傳時間： 2022-02-20
上傳用戶：
超聲波換能器作為一種實用的檢測手段，能實現聲波所攜帶的信息和電能之間轉換。它的性能優良，價格低廉，操作方便，易于調試，因此在工農業生產中發揮著重要的作用。但目前換能器驅動電路的發射頻率多為40 kHz，本文針對1 MHz的超聲波換能器電路進行了設計，主要介紹了它的發射驅動電路和接收驅動電路的設計方案，并對它們的功能進行了詳細地說明。最后搭建實驗平臺，并對電路的輸入、輸出模塊進行了測試。實驗結果表明，換能器電路運行良好，可以為超聲波高精度測量領域的應用提供參考。As a practical means of detection, ultrasonic transducer can realize the conversion between theinformation carried by sound wave and electric energy.It has the advantages of excellent performance,low cost, convenient operation and debugging, so plays an important role in industrial and agriculturalproduction.However, the transmitting frequency of the driving circuit for most transducer is 40 kHz.Thecircuit of 1 MHz ultrasonic transducer is designed In this paper. It mainly introduces the emissive drivingcircuit and the receiving circuit design and the detailed function of them. Finally, the experimentalplatform is built, and the circuit of input and output were tested. Experiments show that the transducer＇ s...
標簽： 換能器 驅動電路
上傳時間： 2022-04-28
上傳用戶：
數字頻率計是電工電子中常用的測量儀器,數字頻率計通過用輸入待測信號對一特定長度的信號進行計數,從而得出頻率并通過數碼管直觀的顯示出來。本文提出了一種與輸入同步的數字頻率計的設計,提高了頻率計的精度,設計采用Multisim軟件進行設計和仿真的過程,介紹了其工作原理,硬件電路設計和仿真的過程。設計采用了Multisim軟件進行設計和仿真,設計結果得到的驗證。Digital frequency counter is used to measure the frequency of a signal.It is common to use a multivibrator to generate a standard 1 second time base signal and count input signal gated by this signal.However,the asynchronous of this time base signal with input signal will bring errors.In this paper,a high precision frequency counter which use synchronized time base signal generator is proposed.This frequency counter is designed and simulated by Multisim tools and result is verified.
標簽： multisim
上傳時間： 2022-05-08
上傳用戶：
VME has been the de-facto bus standard for Commercial off the Shelf(COTS ) Circuit Card Assemblies since the 1980's. VME boards have proven to be remarkably capable of evolving to support newer technologies with innovations such as VME Subsystem Bus, PCI Mezzanine Cards(PMC's) and VME320.However, advances in technologies, appearing particularly in interconnects, have demonstratedthe need for an advance in system development. This advance needs to accommodate high speed interconnect, particularly serial interconnects, and higher power delivery in concert with better heat removal.
標簽： vpx標準
上傳時間： 2022-07-27
上傳用戶：bluedrops
蟲蟲下載站版權所有 京ICP備2021023401號-1
<strike id="gsoek"></strike>