Abstract: This document details the Oceanside (MAXREFDES9#) subsystem reference design, a 3.3V to 15V input,±15V (±12V) output, isolated power supply. The Oceanside design includes a high-efficiency step-up controller, a36V H-bridge transformer driver for isolated supplies, a wide input range, and adjustable output low-dropout linearregulator (LDO). Test results and hardware files are included.
特點（FEATURES） 精確度0.03%滿刻度（Accuracy 0.03%F.S.） 頻率輸入范圍0.01Hz至80KHz（Input range from 0.01 Hz to 80KHz） 16 BIT 隔離類比輸出（16 bit DAC isolating analog output） 輸入與輸出1/輸出2絕緣耐壓 2仟伏特/1分鐘（Dielectric strength 2KVac/1min.（input/output1/output2）） 寬范圍交直流兩用電源設計（Wide input range for auxiliary power） 尺寸小，穩定性高（Dimension small & High stability）
特點(FEATURES) 精確度0.1%滿刻度 (Accuracy 0.1%F.S.) 可作各式數學演算式功能如:A+B/A-B/AxB/A/B/A&B(Hi or Lo)/|A| (Math functioA+B/A-B/AxB/A/B/A&B(Hi&Lo)/|A|/etc.....) 16 BIT 類比輸出功能(16 bit DAC isolating analog output function) 輸入/輸出1/輸出2絕緣耐壓2仟伏特/1分鐘(Dielectric strength 2KVac/1min. (input/output1/output2/power)) 寬范圍交直流兩用電源設計(Wide input range for auxiliary power) 尺寸小,穩定性高(Dimension small and High stability)
Abstract: Uses the MAX641 switching controller and an external discrete charge pump to step up the input voltage. This circuitcan service low loads and is efficient when the output is two, three, four times the input voltage. Adding the MAX627 MOSdriver can further increase the output current capability.
The LT®1943 is a highly integrated, 4-output regulatordesigned to power large TFT LCD panels. The LT1943employs switching regulators—instead of linear regulators—to minimize power dissipation and accommodate awide input voltage range. The wide input range, 4.5V to22V, allows it to accept a variety of power sources,including the commonly used 5V, 12V and 19V AC adaptors.
高的工作電壓高達100V N雙N溝道MOSFET同步驅動 The D810DCDC is a synchronous step-down switching regulator controller that can directly step-down voltages from up to 100V, making it ideal for telecom and automotive applications. The D810DCDC uses a constant on-time valley current control architecture to deliver very low duty cycles with accurate cycle-by-cycle current limit, without requiring a sense resistor. A precise internal reference provides 0.5% DC accuracy. A high bandwidth (25MHz) error amplifi er provides very fast line and load transient response. Large 1Ω gate drivers allow the D810DCDC to drive multiple MOSFETs for higher current applications. The operating frequency is selected by an external resistor and is compensated for variations in VIN and can also be synchronized to an external clock for switching-noise sensitive applications. Integrated bias control generates gate drive power from the input supply during start-up and when an output shortcircuit occurs, with the addition of a small external SOT23 MOSFET. When in regulation, power is derived from the output for higher effi ciency.
Automobile electronic systems place high demands ontoday’s DC/DC converters. They must be able to preciselyregulate an output voltage in the face of wide temperatureand input voltage ranges—including load dump transientsin excess of 60V and cold crank voltage drops to 4V. Theconverter must also be able to minimize battery drain inalways-on systems by maintaining high effi ciency over abroad load current range. Similar demands are made bymany 48V nonisolated telecom applications, 40V FireWireperipherals and battery-powered applications with autoplug adaptors. The LT3437’s best in classperformancemeets all of these requirements in a small thermallyenhanced 3mm × 3mm DFN package.
A number of conventional solutions have been available forthe design of a DC/DC converter where the output voltageis within the input voltage range—a common scenarioin Li-Ion battery-powered applications—but none werevery attractive until now. Conventional topologies, suchas SEPIC or boost followed by buck, have numerousdisadvantages, including low effi ciency, complex magnetics,polarity inversion and/or circuit complexity/cost. TheLTC®3785 buck-boost controller yields a simple, effi cient,low parts-count, single-converter solution that is easyto implement, thus avoiding the drawbacks associatedwith traditional solutions.
Industrial remote monitoring systems and keep-alivecircuits spend most of their time in standby mode. Manyof these systems also depend on battery power, so powersupply effi ciency in standby state is very important tomaximize battery life. The LT®8410/-1 high effi ciencyboost converter is ideal for these systems, requiringonly 8.5μA of quiescent current in standby mode. Thedevice integrates high value (12.4M/0.4M) output feedbackresistors, signifi cantly reducing input current whenthe output is in regulation with no load. Other featuresinclude an integrated 40V switch and Schottky diode,output disconnect with current limit, built in soft-start,overvoltage protection and a wide input range, all in atiny 8-pin 2mm × 2mm DFN package.
The LTC®3610 is a high power monolithic synchronousstep-down DC/DC regulator that can deliver up to 12Aof continuous output current from a 4V to 24V (28Vmaximum) input supply. It is a member of a high currentmonolithic regulator family (see Table 1) that featuresintegrated low RDS(ON) N-channel top and bottomMOSFETs. This results in a high effi ciency and highpower density solution with few external components.This regulator family uses a constant on-time valleycurrent mode architecture that is capable of operatingat very low duty cycles at high frequency and with veryfast transient response. All are available in low profi le(0.9mm max) QFN packages.
