波長信號的解調是實現光纖光柵傳感網絡的關鍵,基于現有的光纖光柵傳感器解調方法,提出一種基于FPGA的雙匹配光纖光柵解調方法,此系統是一種高速率、高精度、低成本的解調系統,并且通過引入雙匹配光柵有效地克服了雙值問題同時擴大了檢測范圍。分析了光纖光柵的測溫原理并給出了該方案軟硬件設計,綜合考慮系統的解調精度和FPGA的處理速度給出了基于拉格朗日的曲線擬合算法。
Abstract:
Sensor is one of the most important application of the fiber grating. Wavelength signal demodulating is the key techniques to carry out fiber grating sensing network, based on several existing methods of fiber grating sensor demodulation inadequate, a two-match fiber grating demodulation method was presented. This system is a high-speed, high precision, Low-cost demodulation system. And by introducing a two-match grating effectively overcomes the problem of double value while expands the scope of testing. This paper analyzes the principle of fiber Bragg grating temperature and gives the software and hardware design of the program. Considering the system of demodulation accuracy and processing speed of FPGA,this paper gives the curve fitting algorithm based on Lagrange.
Abstract: This reference design provides design ideas for a cost-effective, Low-power liquid-level measurement dataacquisition system (DAS) using a compensated silicon pressure sensor and a high-precision delta-sigma ADC. Thisdocument discusses how to select the compensated silicon pressure sensor, suggest system algorithms, and providenoise analyses. It also describes calibration ideas to improve system performance while also reducing complexity andcost.
A Computer-On-Module, or COM, is a Module with all components necessary for a bootable host computer, packaged as a super component. A COM requires a Carrier Board to bring out I/O and to power up. COMs are used to build single board computer solutions and offer OEMs fast time-to-market with reduced development cost. Like integrated circuits, they provide OEMs with significant freedom in meeting form-fit-function requirements. For all these reasons the COM methodology has gained much popularity with OEMs in the embedded industry. COM Express® is an open industry standard for Computer-On-Modules. It is designed to be future proof and to provide a smooth transition path from legacy parallel interfaces to LVDS (Low Voltage Differential Signaling) interfaces. These include the PCI bus and parallel ATA on the one hand and PCI Express and Serial ATA on the other hand.
The NCV7356 is a physical layer device for a single wire data linkcapable of operating with various Carrier Sense Multiple Accesswith Collision Resolution (CSMA/CR) protocols such as the BoschController Area Network (CAN) version 2.0. This serial data linknetwork is intended for use in applications where high data rate is notrequired and a Lower data rate can achieve cost reductions in both thephysical media components and in the microprocessor and/ordedicated logic devices which use the network.The network shall be able to operate in either the normal data ratemode or a high-speed data download mode for assembly line andservice data transfer operations. The high-speed mode is onlyintended to be operational when the bus is attached to an off-boardservice node. This node shall provide temporary bus electrical loadswhich facilitate higher speed operation. Such temporary loads shouldbe removed when not performing download operations.The bit rate for normal communications is typically 33 kbit/s, forhigh-speed transmissions like described above a typical bit rate of83 kbit/s is recommended. The NCV7356 features undervoltagelockout, timeout for faulty blocked input signals, output blankingtime in case of bus ringing and a very Low sleep mode current.
The CC1101 is a Low-cost sub- 1 GHztransceiver designed for very Low-powerwireless applications. The circuit is mainlyintended for the ISM (Industrial, Scientific andMedical) and SRD (Short Range Device)frequency bands at 315, 433, 868, and 915MHz, but can easily be programmed foroperation at other frequencies in the 300-348MHz, 387-464 MHz and 779-928 MHz bands.CC1101 is an improved and code compatibleversion of the CC1100 RF transceiver. Themain improvements on the CC1101 include:
The LPC2292/2294 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 256 kB of embedded high-speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 pct with minimal performance penalty.
With their 144-pin package, Low power consumption, various 32-bit timers, 8-channel 10-bit ADC, 2/4 (LPC2294) advanced CAN channels, PWM channels and up to nine external interrupt pins these microcontrollers are particularly suitable for automotive and industrial control applications as well as medical systems and fault-tolerant maintenance buses. The number of available fast GPIOs ranges from 76 (with external memory) through 112 (single-chip). With a wide range of additional serial communications interfaces, they are also suited for communication gateways and protocol converters as well as many other general-purpose applications.
Remark: Throughout the data sheet, the term LPC2292/2294 will apply to devices with and without the /00 or /01 suffix. The suffixes /00 and /01 will be used to differentiate from other devices only when necessary.
Abstract: High-speed and Low-speed data converters serve critical functions in modern broadband mobile radios. This application note outlines how todetermine high-speed data converter performance requirements in baseband sampling radio architectures. Also, system partition strategies andadvantages are outlined when considering a high-speed analog front-end (AFE) solution.
We offer a broad line of high performance Low dropout (LDO) linear regulators with fasttransient response, excellent line and load regulation, and very wide input voltage rangefrom 0.9V to 100V. Output currents range from 20mA to 10A, with positive, negative andmultiple output versions available. Many devices offer output voltage operation <0.8V andsome feature operation as Low as 0V, even with a single supply. Most are stable with ceramicoutput capacitors. LDO regulators can be applied in virtually any application.