為降低成本和解決現有膜片鉗放大器系統中PC機的干擾問題，研究了一種基于單片機的膜片鉗放大器小系統。該系統采用ADI公司生產的ADuC841作為控制核心，并且配置相應的液晶顯示模塊LCM3202401。模擬電路部分采用高輸入阻抗的AD8627實現微電流信號的采集，并由后級電路進行信號的放大和電阻電容的補償。它具有硬件電路簡單、體積小、使用方便的特點。既可以單獨作為小系統實現采集和顯示，也可以通過紅外方式和PC機進行通訊，在PC機上進行信號的處理。
Abstract:
In order to reduce cost and resolve the interferential problem with PC in existing patch clamp amplifiers, a small patch clamp amplifier system design based on microcontroller is studied. It adopts a new high performance microconverter ADuC841 by the ADI as the control core in the system, configuring a liquid crystal module LCM3202401. In the analog circuit, AD8627 with high input impedance is used to detect the low current，signal magnification, as well as resistance and capacitance compensation are accomplished by subsequent circuits. It has the advantage of simple hardware circuit design, small volume and convenient operation. It can either be used as an independent system to measure and show signal detected or transmit to PC by infrared ray.
在需要實時大量輸入漢字的顯示控制處理應用中，利用傳統單片機實現顯示控制的設計方法是較難實現的。帶漢字字庫的液晶模塊的使用使得小容量ROM單片機的大量漢字信息輸入與顯示成為可能。提出了針對漢字字庫編碼的二級索引拼音輸入檢索方法,介紹了以ST7920作為控制器的帶漢字字庫的液晶顯示模塊的接口方法及漢字顯示和控制原理，給出了通用計算機鍵盤在單片機中的串行接口，采用該技術可大大增強單片機的漢字輸入功能。為小容量ROM單片機的大批量漢字信息處理提供了一種漢字輸入解決方案。
Abstract:
It is difficult to realize Chinese characters input method based on the embedded system by using the traditional design method of display control. It is possible to input and display Chinese characters based on the embedded system with the ROM of small content by using the LCD module with Chinese characters.Chinese characters input method of the quadric index recall in allusion to Chinese characters code is brought forward.The interface and the principle of Chinese characters display control based on the LCD module controlled with the ST7920 is introduced too.The serial interface of the computer keyboard in common use and the embedded system is given at the same time. It can enhance the embedded system function of Chinese characters input by using this technology, and provide a kind of Chinese characters input scheme for the embedded system with small capacity ROM.
針對船舶氣象儀保障維修而設計的船舶氣象儀測試系統，包括信息處理終端、主儀器檢測模塊、傳感器檢測模塊，各個模塊都采用基于AVR單片機的嵌入式系統，模塊之間通過CAN總線進行通信。結果表明，船舶氣象儀測試系統能夠快速檢測船舶氣象儀故障，與單純依靠人工方式排查故障相比，故障檢測時間縮短了60%以上。
Abstract:
The test system of ship meteorological instrument was developed to satisfy the maintenance of ship meteorological instruments，which composed of information processing terminal， testing module of main instrument and testing module of sensors. Each of these modules included an embedded system based on microcontroller of AVR series and communicated with other module by CAN bus. The results show that the test system can judge the fault of ship meteorological instrument quickly and shorten the fault detection time as much as 60% compared with simple manual troubleshooting.
Luminary Micro provides an analog-to-digital converter (ADC) module on some members of theStellaris microcontroller family. The hardware resolution of the ADC is 10 bits; however, due to noiseand other accuracy-diminishing factors, the true accuracy is less than 10 bits. This application noteprovides a software-based oversampling technique, resulting in an improved Effective Number OfBits (ENOB) in the conversion result. This document describes methods of oversampling an inputsignal, and the impact on precision and overall system performance.
基于單片機控制的二氧化碳濃度測試計:基于CDM4161二氧化碳氣體濃度測試模塊以及ATtiny26單片機,提出了一種二氧化碳濃度測試計的設計方案。該方案具有硬件電路簡單、成本低、可靠性高、測量準確等優點，具有較高的實用價值。 Abstract: Abstract：A desigh scheme of CO2 concentration meter based on CDM4161carbon dioxide concentration test module and ATtiny26micro-controller is presented in this paper.The design scheme features simple hardware circuit,low-cost,high reli-ability，accurate measurement and it has a high practical value.
基于USB接口的數據采集模塊的設計與實現Design and Implementation of USB-Based Data Acquisition Module路 永 伸(天津科技大學電子信息與自動化學院，天津300222)摘要文中給出基于USB接口的數據采集模塊的設計與實現。硬件設計采用以Adpc831與PDIUSBDI2為主的器件進行硬件設計，采用Windriver開發USB驅動，并用Visual C十十6.0對主機軟件中硬件接口操作部分進行動態鏈接庫封裝。關鍵詞USB 數據采集Adpc831 PDNSBDI2 Windriver動態鏈接庫Abstract T hed esigna ndim plementaitono fU SB-BasedD ataA cquisiitonM oduleis g iven.Th ec hips oluitonm ainlyw ithA dpc831a ndP DTUSBD12i sused for hardware design. The USB drive is developed場Wmdriver, and the operation on the hardware interface is packaged into Dynamic Link Libraries場Visual C++6.0. Keywords USB DataA cquisition Adttc831 PDfUSBD12 Windriver0 引言US B總 線 是新一代接口總線，最初推出的目的是為了統一取代PC機的各類外設接口，迄今經歷了1.0,1.1與2.0版本3個標準。在國內基于USB總線的相關設計與開發也得到了快速的發展，很多設計者從各自的應用領域，用不同方案設計出了相應的裝置[1,2]。數據采集是工業控制中一個普遍而重要的環節，因此開發基于USB接口的數據采集模塊具有很強的現實應用意義。雖然 US B總線標準已經發展到2.0版本，但由于工業控制現場干擾信號的情況比較復雜，高速數據傳輸的可靠性不容易被保證，并且很多場合對數據采集的實時性要求并不高，開發2.0標準產品的成本又較1.1標準產品高，所以筆者認為，在工業控制領域，目前開發基于USB總線1.1標準實現的數據采集模塊的實用意義大于相應2.0標準模塊。
The Tri-Mode Ethernet MAC (TEMAC) UltraController-II module is a minimal footprint,embedded network processing engine based on the PowerPC™ 405 (PPC405) processor coreand the TEMAC core embedded within a Virtex™-4 FX Platform FPGA. The TEMACUltraController-II module connects to an external PHY through Gigabit Media IndependentInterface (GMII) and Management Data Input/Output (MDIO) interfaces and supports tri-mode(10/100/1000 Mb/s) Ethernet. Software running from the processor cache reads and writesthrough an On-Chip Memory (OCM) interface to two FIFOs that act as buffers between thedifferent clock domains of the PPC405 OCM and the TEMAC.
在研究傳統家用燃氣報警器的基礎上，以ZigBee協議為平臺，構建mesh網狀網絡實現網絡化的智能語音報警系統。由于傳感器本身的溫度和實際環境溫度的影響，傳感器標定后采用軟件補償方法。為了減少系統費用，前端節點采用半功能節點設備，路由器和協調器采用全功能節點設備，構建mesh網絡所形成的家庭內部報警系統，通過通用的電話接口連接到外部的公用電話網絡，啟動語音模塊進行報警。實驗結果表明，在2.4 GHz頻率下傳輸，有墻等障礙物的情況下，節點的傳輸距離大約為35 m，能夠滿足家庭需要，且系統工作穩定，但在功耗方面仍需進一步改善。
Abstract:
On the basis of studying traditional household gas alarm system, this paper proposed the platform for the ZigBee protocol，and constructed mesh network to achieve network-based intelligent voice alarm system. Because of the sensor temperature and the actual environment temperature, this system design used software compensation after calibrating sensor. In order to reduce system cost, semi-functional node devices were used as front-end node, however, full-function devices were used as routers and coordinator，constructed alarm system within the family by building mesh network，connected to the external public telephone network through the common telephone interface, started the voice alarm module. The results indicate that nodes transmit about 35m in the distance in case of walls and other obstacles by 2.4GHz frequency transmission, this is able to meet family needs and work steadily, but still needs further improvement in power consumption.
TheTool is highy customizable map editor(based on QT) which can be extended via LUA scripts. A first implentation is ready and can be published to the public. The editor is the perfect tool who wants to design some 3d games but don t have time to write
This article is based in part on Bob Place s ADO is AOK (a simple ADO tutorial). Wrapper Usage This is consist of 2 classes. CDyndb : This Class manages connections and recordsets. Recordsets are organized as linked list (CList) and you can access them using their ids. CDynRec : This class is the node to populate for each recordsets. ADO封裝器類 這篇文章一部分基于Bob Place的《ADO is AOK》 (簡單的ADO指導) 。 包裹的用法 由2個類組成。 類CDyndb: 這個類別管理連接和記錄集。記錄集是連接起來的記錄的集合，你可以通過他們的ID訪問他們。 類CDynRec: 這個類別存放記錄集的代碼。
