針對船舶氣象儀保障維修而設計的船舶氣象儀測試系統，包括信息處理終端、主儀器檢測模塊、傳感器檢測模塊，各個模塊都采用基于AVR單片機的嵌入式系統，模塊之間通過CAN總線進行通信。結果表明，船舶氣象儀測試系統能夠快速檢測船舶氣象儀故障，與單純依靠人工方式排查故障相比，故障檢測時間縮短了60%以上。 Abstract: The test system of ship meteorological instrument was developed to satisfy the maintenance of ship meteorological instruments，which composed of information processing terminal， testing module of main instrument and testing module of sensors. Each of these modules included an embedded system based on microcontroller of AVR series and communicated with other module by CAN bus. The results show that the test system can judge the fault of ship meteorological instrument quickly and shorten the fault detection time as much as 60% compared with simple manual troubleshooting.
上傳時間： 2013-11-23
上傳用戶：stvnash
介紹了一種基于MSP430系列單片機和ADXL203加速度傳感器的數字式傾角儀，它不僅可以實現水平度檢測，而且可以測量00～3600范圍內的任意傾角，分辨率可達O．1。。此外，由于該傾角儀輸出為數字結果，因此它也可以與其他的數字設備結合起來，組合成一個功能更加強大的儀器。該數字傾角儀可廣泛應用于建筑、機械、道路、橋梁、石油、煤礦和地質勘探等各種需要測量重力參考系下傾角的場合。關鍵詞：MSP430F133單片機；力敏傳感器；ADXL203加速度計；角度測量 Abstract：This paper presents a new style digital inclinometer which is developed on the basis of the MSP430F133 MCU and the ADXL203 dual axis aeeelerometer．This inclinometer not only can test levelness，but also can measure any angle between 0。and 360。with an accuracy of 0．1 O．In addition，its output is a digital result，which makes it possible to integrate itself with other digital devices to form a more functional unit．This inclinometer can be widely used in any construction site，oil field，coal-mine or geologic survey and SO on where it will provide the working people with convenience to measure any angles．Key words：MSP430F133 MCU；force sensor；ADXL203 accelerometer；angle measurement
上傳時間： 2013-11-14
上傳用戶：lizhizheng88
The MSP-FET430U14 is a powerful flash emulation tool to quickly begin application development on the MSP430 MCU. It includes USB debugging interface used to program and debug the MSP430 in-system through the JTAG interface or the pin saving Spy Bi-Wire (2-wire JTAG) protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is ultra-low power, no external power supply is required. The debugging tool interfaces the MSP430 to the included integrated software environment and includes code to start your design immediately. The MSP-FET430UIF development tools supports development with all MSP430 flash devices
上傳時間： 2013-10-28
上傳用戶：13691535575
常用三星單片機燒寫電壓設置參考表 燒寫電壓說明:Vdd 電壓指燒寫時加載到芯片Vdd 端子的邏輯電壓,Vpp 電壓指燒寫時加載到芯片Vpp(Test)端子的編程電壓, Vpp=12V 是編程器的默認燒寫電壓,無須特別設置. 由于編程器的默認輸出Vpp 電壓均為12V,因此在燒寫Vpp=3.3V/5.0V 的芯片時,需要對燒寫轉換適配器作以下改動:將燒寫器燒寫座引出的Vpp 端子完全空置不用, 并在適配器上將Vdd端子直接連接Vpp 端即可.當用戶采用在PCB板上燒寫方式時,建議最好能在PCB芯片端的Vpp腳并接一個104 的電容入地,可有效保護在燒寫電壓加載時板子電路共同作用產生的瞬間過壓脈沖不會輸入到Vpp 腳而造成Vpp 擊穿.S3F84K4 燒寫特別說明,由于三星半導體DATA SHEET 要求在對該芯片進行燒寫時,須在Vpp 腳加接一個101 的電容到地,因此在使用我站各款燒寫器燒寫84K4 時,須將燒寫器主板上的Vpp 端原來并接的10uf/50V-電解電容和104 電容去掉,另行并接一個101 電容入地即可.不過,據本人特別測試結果,其實不做以上處理對燒寫過程沒有任何影響, 估計可能是三星半導體對芯片有做過改版,老版本的84K4 才會有以上特別要求,新版本是沒有這個要求的.
上傳時間： 2013-10-10
上傳用戶：wcl168881111111
Nios 的用戶定義接口邏輯實例 有許多人問我使用 Nios 的用戶定義接口邏輯怎么用，想了幾天決定設計一個實例來說明。該例為一個使用 user to interface logic 設計的 PWM 實例，其中包括三個文件： plus32.v 是一個為 32bit nios 設計的 pwm 實例。 plus16.v 是一個為 16bit nios 設計的 pwm 實例。 test.s 是一個使用中斷調用 pwm 的匯編語言測試程序。以上模塊和程序均調試通過，并可穩定工作。這里讓大家參考是使大家通過該例來真正理解 user to interface logic 設計方法，和nios 中通過匯編調用中斷的方法，所以超值喔。另外熱烈歡迎大家的指導。 注：在設計 Nios 時，將你調用的 user to interface logic 插件重命名為 plus_0，這樣我的 test.s 可不作任何改動，你就可用示波器通過 nios 的 plus 管腳觀察到一個要求的輸出。
上傳時間： 2013-11-15
上傳用戶：cc1915
Designing Boards with Atmel AT89C51, AT89C52, AT89C1051, and AT89C2051 for Writing Flash at In-Circuit Test:Recent improvements in chips andtesters have made it possible for thetester to begin taking over the role traditionallyassigned to the PROM programmer.Instead of having a PROM programmerwrite nonvolatile memoriesbefore assembling the board, the in-circuittester writes them during in-circuittesting operations. Many Teradyne Z18-series testers are now in use loadingcode into nonvolatile memories, microcontrollersand in-circuit programmable logic devices. The purpose of this note is to explain how the Z18 approaches the writing task for Atmel AT89C series IC’s,so that designers of boards using these chips can get the best results.
標簽： Designing Boards Atmel with
上傳時間： 2013-11-20
上傳用戶：lijianyu172
SPCE061A采用的內核 SPCE061A采用的內核（CPU）為μ‘nSP。 μ‘nSP（讀做micro-n-S-P）是凌陽科技推出的16位微處理器，它的突出特點是較高的處理速度，這就使其有能力進行復雜的數字信號處理（DSP，Digital Signal Processing）。 μ‘nSP內核由凌陽自主開發，因而也具備它自己的指令系統。 指令系統.61 3.1 指令系統的概述及符號約定.61 3.2 數據傳送指令62 3.3 算術運算..66 3.3.1 加法運算..67 3.3.2 減法運算..68 3.3.3 帶進位的加減運算.70 3.3.4 取補運算..70 3.3.5 SPCE061A的乘法指令.71 3.3.6 SPCE061A的n項內積運算指令.71 3.3.7 比較運算(影響標志位N,Z,S,C)..73 3.4 SPCE061A的邏輯運算.74 3.4.1 邏輯與..74 3.4.2 邏輯或..75 3.4.3 邏輯異或..76 3.4.4 測試（TEST）.78 3.4.5 SPCE061A的移位操作.80 3.5 SPCE061A的控制轉移類指令..83 3.6 偽指令86 3.6.1 偽指令的語法格式及特點..87 3.6.2 偽指令符號約定..87 3.6.3 標準偽指令.87 3.6.4 宏定義與調用98 3.6.5 段的定義與調用101 3.6.6 結構的定義與調用..102 3.6.7 過程的定義與調用..106 3.6.8 偽指令的應用舉例..106
上傳時間： 2013-10-31
上傳用戶：xuanchangri
基于單片機控制的二氧化碳濃度測試計:基于CDM4161二氧化碳氣體濃度測試模塊以及ATtiny26單片機,提出了一種二氧化碳濃度測試計的設計方案。該方案具有硬件電路簡單、成本低、可靠性高、測量準確等優點，具有較高的實用價值。 Abstract: Abstract：A desigh scheme of CO2 concentration meter based on CDM4161carbon dioxide concentration test module and ATtiny26micro-controller is presented in this paper.The design scheme features simple hardware circuit,low-cost,high reli-ability，accurate measurement and it has a high practical value.
上傳時間： 2013-11-14
上傳用戶：zjwangyichao
The C500 microcontroller family usually provides only one on-chip synchronous serialchannel (SSC). If a second SSC is required, an emulation of the missing interface mayhelp to avoid an external hardware solution with additional electronic components.The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using optimized SW routines with a performance up to 25KBaud in Slave Mode with half duplex transmission and an overhead less than 60% atSAB C513 with 12 MHz. Due to the implementation in C this performance is not the limitof the chip. A pure implementation in assembler will result in a strong reduction of theCPU load and therefore increase the maximum speed of the interface. In addition,microcontrollers like the SAB C505 will speed up the interface by a factor of two becauseof an optimized architecture compared with the SAB C513.Moreover, this solution lays stress on using as few on-chip hardware resources aspossible. A more excessive consumption of those resources will result in a highermaximum speed of the emulated interface.Due to the restricted performance of an 8 bit microcontroller a pin compatible solution isprovided only; the internal register based programming interface is replaced by a set ofsubroutine calls.The attached source files also contain a test shell, which demonstrates how to exchangeinformation between an on-chip HW-SSC and the emulated SW-SSC via 5 external wiresin different operation modes. It is based on the SAB C513 (Siemens 8 bit microcontroller).A table with load measurements is presented to give an indication for the fraction of CPUperformance required by software for emulating the SSC.
標簽： synchronous Emulating serial
上傳時間： 2014-01-31
上傳用戶：z1191176801
The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using SW routines implemented in C. The code is focused onthe SAB C513, but will fit to all C500 derivatives.Beyond the low level software drivers a test shell is delivered. This shell allows a quicktest of the software drivers by an emulator or a starter kit demo board.
上傳時間： 2013-11-24
上傳用戶：363186
