This application note provides step-by-step instructions on how to recreate a Tri-Mode Ethernet(TEMAC) performance testing system using the ML405 board and MontaVista Linux 4.0. Thisapplication note shows how to set up a simple EDK Base System Builder system on the ML405Evaluation Platform and run performance tests. The network architecture for the test isdescribed. A system is built and downloaded into the FPGA. A MontaVista Linux kernel isconfigured, built, and downloaded into the ML405 Evaluation Platform. The instructions forobtaining and setting up the software used to perform the measurements, netperf, are given.
The correct answer for each test bank question is highlighted in bold. Test bank questions are based on the end-of-chapter questions. If a student studies the end-of-chapter questions (which are linked to the italicized words in each chapter), then they will be successful on the test bank questions.
This application note covers the design considerations of a system using the performance
features of the LogiCORE™ IP Advanced eXtensible Interface (AXI) Interconnect core. The
design focuses on high system throughput through the AXI Interconnect core with F
MAX
and
area optimizations in certain portions of the design.
The design uses five AXI video direct memory access (VDMA) engines to simultaneously move
10 streams (five transmit video streams and five receive video streams), each in 1920 x 1080p
format, 60 Hz refresh rate, and up to 32 data bits per pixel. Each VDMA is driven from a video
test pattern generator (TPG) with a video timing controller (VTC) block to set up the necessary
video timing signals. Data read by each AXI VDMA is sent to a common on-screen display
(OSD) core capable of multiplexing or overlaying multiple video streams to a single output video
stream. The output of the OSD core drives the DVI video display interface on the board.
Performance monitor blocks are added to capture performance data. All 10 video streams
moved by the AXI VDMA blocks are buffered through a shared DDR3 SDRAM memory and are
controlled by a MicroBlaze™ processor.
The reference system is targeted for the Virtex-6 XC6VLX240TFF1156-1 FPGA on the
Xilinx® ML605 Rev D evaluation board
針對傳統集成電路（ASIC）功能固定、升級困難等缺點，利用FPGA實現了擴頻通信芯片STEL-2000A的核心功能。使用ISE提供的DDS IP核實現NCO模塊，在下變頻模塊調用了硬核乘法器并引入CIC濾波器進行低通濾波，給出了DQPSK解調的原理和實現方法，推導出一種簡便的引入?仔/4固定相移的實現方法。采用模塊化的設計方法使用VHDL語言編寫出源程序，在Virtex-II Pro 開發板上成功實現了整個系統。測試結果表明該系統正確實現了STEL-2000A的核心功能。
Abstract:
To overcome drawbacks of ASIC such as fixed functionality and upgrade difficulty, FPGA was used to realize the core functions of STEL-2000A. This paper used the DDS IP core provided by ISE to realize the NCO module, called hard core multiplier and implemented CIC filter in the down converter, described the principle and implementation detail of the demodulation of DQPSK, and derived a simple method to introduce a fixed phase shift of ?仔/4. The VHDL source code was designed by modularity method , and the complete system was successfully implemented on Virtex-II Pro development board. Test results indicate that this system successfully realize the core function of the STEL-2000A.
為了在CDMA系統中更好地應用QDPSK數字調制方式，在分析四相相對移相（QDPSK)信號調制解調原理的基礎上，設計了一種QDPSK調制解調電路，它包括串并轉換、差分編碼、四相載波產生和選相、相干解調、差分譯碼和并串轉換電路。在MAX+PLUSⅡ軟件平臺上，進行了編譯和波形仿真。綜合后下載到復雜可編程邏輯器件EPM7128SLC84-15中，測試結果表明，調制電路能正確選相，解調電路輸出數據與QDPSK調制輸入數據完全一致，達到了預期的設計要求。
Abstract:
In order to realize the better application of digital modulation mode QDPSK in the CDMA system， a sort of QDPSK modulation-demodulation circuit was designed based on the analysis of QDPSK signal modulation-demodulation principles. It included serial/parallel conversion circuit, differential encoding circuit, four-phase carrier wave produced and phase chosen circuit, coherent demodulation circuit, difference decoding circuit and parallel/serial conversion circuit. And it was compiled and simulated on the MAX+PLUSⅡ software platform,and downloaded into the CPLD of EPM7128SLC84-15.The test result shows that the modulation circuit can exactly choose the phase，and the output data of the demodulator circuit is the same as the input data of the QDPSK modulate. The circuit achieves the prospective requirement of the design.
UART 4 UART參考設計，Xilinx提供VHDL代碼 uart_vhdl
This zip file contains the following folders:
\vhdl_source -- Source VHDL files:
uart.vhd - top level file
txmit.vhd - transmit portion of uart
rcvr.vhd - - receive portion of uart
\vhdl_testfixture -- VHDL Testbench files. This files only include the testbench behavior, they
do not instantiate the DUT. This can easily be done in a top-level VHDL
file or a schematic. This folder contains the following files:
txmit_tb.vhd -- Test bench for txmit.vhd.
rcvr_tf.vhd -- Test bench for rcvr.vhd.
