This application note shows how to achieve low-cost, efficient serial configuration for Spartan FPGA designs. The approachrecommended here takes advantage of unused resources in a design, thereby reducing the cost, part count, memory size,and board space associated with the serial configuration circuitry. As a result, neither processor nor PROM needs to be fullydedicated to performing Spartan configuration.In particular, information is provided on how the idle processing time of an on-board controller can be used to loadconfiguration data from an off-board source. As a result, it is possible to upgrade a Spartan design in the field by sending thebitstream over a network.
This application note describes how to build a system that can be used for determining theoptimal phase shift for a Double Data Rate (DDR) memory feedback clock. In this system, theDDR memory is controlled by a controller that attaches to either the OPB or PLB and is used inan embedded microprocessor application. This reference system also uses a DCM that isconfigured so that the phase of its output clock can be changed while the system is running anda GPIO core that controls that phase shift. The GPIO output is controlled by a softwareapplication that can be run on a PowerPC® 405 or Microblaze™ microprocessor.
The SDI standards are the predominant standards for uncompressed digital videointerfaces in the broadcast studio and video production center. The first SDI standard,SD-SDI, allowed standard-definition digital video to be transported over the coaxial cableinfrastructure initially installed in studios to carry analog video. Next, HD-SDI wasto support high-definition video. Finally, dual link HD-SDI and 3G-SDIdoubled the bandwidth of HD-SDI to support 1080p (50 Hz and 60 Hz) and other videoformats requiring more bandwidth than HD-SDI provides.
This application note covers the design considerations of a system using the performance
features of the LogiCORE™ IP Advanced eXtensible Interface (AXI) Interconnect core. The
design focuses on high system throughput through the AXI Interconnect core with F
MAX
and
area optimizations in certain portions of the design.
The design uses five AXI video direct memory access (VDMA) engines to simultaneously move
10 streams (five transmit video streams and five receive video streams), each in 1920 x 1080p
format, 60 Hz refresh rate, and up to 32 data bits per pixel. Each VDMA is driven from a video
test pattern generator (TPG) with a video timing controller (VTC) block to set up the necessary
video timing signals. Data read by each AXI VDMA is sent to a common on-screen display
(OSD) core capable of multiplexing or overlaying multiple video streams to a single output video
stream. The output of the OSD core drives the DVI video display interface on the board.
Performance monitor blocks are added to capture performance data. All 10 video streams
moved by the AXI VDMA blocks are buffered through a shared DDR3 SDRAM memory and are
controlled by a MicroBlaze™ processor.
The reference system is targeted for the Virtex-6 XC6VLX240TFF1156-1 FPGA on the
Xilinx® ML605 Rev D evaluation board
This application note describes a reference system which illustrates how to build an embeddedPowerPC® system using the Xilinx 1-Gigabit Ethernet Media Access Controller processor core.This system has the PLB_Gemac configured to use Scatter/Gather Direct Memory Access andthe Serializer/Deserializer (SerDes) interface. This application note describes how to set up thespecific clocking structure required for the SerDes interface and the constraints to be added tothe UCF file. This reference system is complete with a standalone software application to testsome of the main features of this core, including access to registers, DMA capabilities, transmitand receive in loopback mode. This reference system is targeted for the ML300 evaluationboard.
The Tri-Mode Ethernet MAC (TEMAC) UltraController-II module is a minimal footprint,embedded network processing engine based on the PowerPC™ 405 (PPC405) processor coreand the TEMAC core embedded within a Virtex™-4 FX Platform FPGA. The TEMACUltraController-II module connects to an external PHY through Gigabit Media IndependentInterface (GMII) and Management Data Input/Output (MDIO) interfaces and supports tri-mode(10/100/1000 Mb/s) Ethernet. Software running from the processor cache reads and writesthrough an On-Chip Memory (OCM) interface to two FIFOs that act as buffers between thedifferent clock domains of the PPC405 OCM and the TEMAC.
特點 最高輸入頻率 10KHz 顯示范圍0-9999（一段設定）0至999999累積量 計數速度 50/10000脈波/秒可選擇 輸入脈波具有預設刻度功能 累積量同步（批量）或非同步（批次）計數可選擇 數位化指撥設定操作簡易 計數暫時停止功能 1組報警功能 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脈波觸發電位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高輸入頻率: <10KHz (up,down,up/down mode) 輸出動作時間 : 0.1 to 99.9 second adjustable 輸出復歸方式: Manual(N) or automatic (R or C) can be modif 繼電器容量: AC 250V-5A, DC 30V-7A 顯示值范圍: 0-9999（PV,SV） 0-999999(TV) 顯示幕: Red high efficiency LEDs high 7.0mm (.276")(PV,SV) Red high efficiency LEDs high 9.2mm (.36")(TV) 參數設定方式: Touch switches 感應器電源: 12VDC +/-3%(<60mA) 記憶方式: Non-volatile E2PROM memory 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用環境條件: 0-50℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
特點 顯示值范圍-199999至999999位數 最高輸入頻率 5KHz 90度相位差加減算具有提高解析度4倍功能 輸入脈波具有預設刻度功能 定位基準值可任意設定 比較磁滯值可任意設定 數位化指撥設定操作簡易 3組繼電器輸出功能 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脈波觸發電位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高輸入頻率: <5KHz 定位置范圍: -199999 to 999999 second adjustabl 比較磁滯范圍: 0 to 9999 adjustable 繼電器容量: AC 250V-5A, DC 30V-7A 顯示值范圍: -199999 to 999999 顯示幕: Red high efficiency LEDs high 9.2mm (.36") 參數設定方式: Touch switches 感應器電源: 12VDC +/-3%(<60mA) 記憶方式: Non-volatile E2PROM memory 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用環境條件: 0-50℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
特點 精確度0.25%滿刻度 ±1位數 輸入配線系統可任意選擇 CT比可任意設定 具有異常電流值與異常次數記錄保留功能 電流過高或過低檢測可任意設定 報警繼電器復歸方式可任意設定 尺寸小,穩定性高 2.主要規格 輔助電源: AC110V&220V ±20%(50 or 60Hz) AC220V&440V ±20%(50 or 60Hz)(optional) 精確度: 0.25% F.S. ±1 digit 輸入負載: <0.2VA (Current) 最大過載能力 : Current related input: 2 x rated continuous 10 x rated 30 sec. 25 x rated 3sec. 50 x rated 1 sec. 輸入電流范圍: AC0-5A (10-1000Hz) CT ratio : 1-2000 adjustable 啟動延遲動作時間: 0-99.9 second adjustable 繼電器延遲動作時間: 0-99.9 second adjustable 繼電器復歸方式: Manual (N) / latch(L) can be modified 繼電器磁滯范圍: 0-999 digit adjustable 繼電器動作方向: HI /LO/GO/HL can be modified 繼電器容量: AC 250V-5A, DC 30V-7A 過載顯示: "doFL" 溫度系數: 50ppm/℃ (0-50℃) 顯示幕: Red high efficiency LEDs high 14.22mm(.56")(PV) Red high efficiency LEDs high 14.22mm(.276")(NO) 參數設定方式: Touch switches 記憶型式 : Non-volatile E2PROM memory 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 1600Vdc(input/output 使用環境條件 : 0-50℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
