#include<reg51.h> #define uchar unsigned char #define uint unsigned int uint i,j; sbit dula=P2^6; sbit wela=P2^7; uchar code table[]={0x3f,0x06,0x5b,0x4f,0x66,0x6d, 0x7d,0x07,0x7f,0x6f,0x77,0x7c, 0x39,0x5e,0x79,0x71}; void main() { j=0; i=0; TMOD=0X01; TH0=(65536-50000)/256; TL0=(65536-50000)%6; EA=1; ET0=1; TR0=1; while(1); } void time0() interrupt 1 { TH0=(65536-50000)/256; TL0=(65536-50000)%6; i++; if(i==15) { P0=table[j]; dula=1; dula=0; P0=0XC0; wela=1; wela=0; j++; i=0; if(j==16) { j=0; } } }
標簽： 用定時器以間隔500MS在6位數碼管上依次顯示0、1、 2、3….C、D、E、F，重復。
上傳時間： 2016-02-11
上傳用戶：嬌縱Pamper
/**************************************************************** 外部晶振8M PA0~3：四位數碼管的位選 PB0~7：數碼管的8位段選 外部中斷0用于計數 定時器0溢出中斷的定時為1ms 說明 ：檢測到水流較小時，繼電器延時1秒關閉 ******************************************************************/ #include<iom16v.h> #include<macros.h> #define uchar unsigned char #define uint unsigned int char led_7[10]={0x3F,0x06,0x5B,0x4F,0x66,0x6D,0x7D,0x07,0x7F,0x6F}; //數碼管段選 char position[4]={0xfe,0xfd,0xfb,0xf7};//數碼管位選 uint sumnum=0; //用于記錄1000ms內進入中斷的次數 uint time=0; //記錄進入比較定時器0的次數 uint num=0; //記錄1ms內進入中斷的次數 uint count=0; //進入外部中斷0的次數 uchar flag; uint sumnum1; //記錄100ms內的數目 /***************************函數聲明***************************/ void delay(); void display(uint m ); void init(); void init_0(); void init_2(); void _delay_us(uint l) { unsigned int i; for(i=0;i<l;i++) { asm("nop"); } } /**************************主函數***********************************/ void main() { init(); init_0(); init_2(); while(sumnum<5) { PORTD=0XBF; segdisplay(sumnum1); } while(1) { segdisplay(sumnum1); } } /*************************掃描數碼管時的延時函數*********************/ void delay() { uchar i,j; for(i=6;i>0;i--) for(j=225;j>0;j--); } /************************數碼管顯示函數*****************************/ void segdisplay( int temp) { int seg[]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f}; int temp1,temp2,temp3,temp4; temp1=temp/1000; temp2=(temp/100)%10; temp3=(temp/10)%10; temp4=temp%10; DDRB=0xff; DDRA|=0x0f; PORTA=~BIT(3); PORTB=seg[temp1]; _delay_us(100); PORTA=~BIT(2); PORTB=seg[temp2]; _delay_us(100); PORTA=~BIT(1); PORTB=seg[temp3]; _delay_us(100); PORTA=~BIT(0); PORTB=seg[temp4]; _delay_us(100); } /***********************管腳初始化函數*********************/ void init() { DDRD|=0X40; //PD4 設置為輸出 PORTD=0XBF; DDRA=0XFF; DDRB=0XFF; PORTA=0XFF; PORTB=0XFF; } /***********************外部中斷0初始化*********************/ void init_0() { MCUCR=0X02; //INT0為下降沿觸發 GICR=0X40; //使能INT0中斷 SREG=0X80; //使能總中斷 } /**********************定時器2初始化***********************/ void init_2() { TCCR0=0x03; // 內部時鐘，64 分頻（8M/64=125KHz） TCNT0=0x83; //裝初值 TIMSK=0x01; // 允許 T/C0溢出中斷中斷 } /***********************外部中斷0子函數********************/ #pragma interrupt_handler int0_isr:2 void int0_isr(void) { count++; } /*********************定時計數器0溢出中斷子函數*****************/ #pragma interrupt_handler int0_over:10 void int0_over(void) { TCNT0=0x83; //重裝初值 if((time%100) == 0) sumnum1 = num; if(time == 1000) { sumnum=num; if(sumnum<10) { if((flag==1)&&(sumnum<10)) { PORTD=0XFF; flag=0; } flag++; } else PORTD=0XBF; num=0; time=0; } num+=count; count=0; ++time; }
標簽： C語言
上傳時間： 2016-03-09
上傳用戶：彥 yan
#include <iostream> using namespace std; class Student { public: Student(int, int); int num; int grade; }; Student::Student(int n, int g) { num = n; grade = g; } int maxGradeIndex(Student* s) { int maxGrade, index = 0, i = 0; maxGrade = s[0].grade; for (i = 0; i<5; i++) { if (s[i].grade > maxGrade) { maxGrade = s[i].grade; index = i; } } return index; } int main() { Student a[5] = { Student(1, 86), Student(2, 60), Student(3, 72), Student(4, 95), Student(5, 66) }; int maxGradeStNum = maxGradeIndex(a); cout << "成績最好學生的學號是:" << a[maxGradeStNum].num << endl; cout << "成績最好學生的成績是:" << a[maxGradeStNum].grade << endl; getchar(); return 0; }
上傳時間： 2016-04-23
上傳用戶：burt1025
#include "STC90.h" #include < intrins.h > #define uchar unsigned char #define uint unsigned int #define led_port P1 sbit IR_RE = P3^2; sbit led_r = P1^3; sbit led_g = P1^4; sbit led_b = P1^5; sbit led_wd = P1^7; sbit K1 =P3^0 ; //增加鍵 sbit K2 =P3^1 ; //減少鍵 sbit BEEP =P3^7 ; //蜂鳴器 uchar temp,temp1; bit k=0; //紅外解碼判斷標志位，為0則為有效信號，為1則為無效 bit Flag2; uchar date[4]={0,0,0,0}; //date數組為存放地址原碼，反碼，數據原碼，反碼 uint lade_1,lade_2,lade_3,lade_4; uint num; uchar date_ram,ee_temp,ee_temp1; uchar WDT_NUM=0; uchar const dofly[]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f};// 顯示段碼值01234567 uchar code seg[]={7,6,5,4,3,2,1,0};//分別對應相應的數碼管點亮,即位碼 unsigned long disp_date; void fade(); void fade1(); /*************************** 看門狗子程序*************************/ void watchdog_timer() { if(WDT_NUM==5) { WDT_NUM=0; led_wd=!led_wd; } WDT_NUM++; WDT_CONTR=0x3f; } /******************************************************************/ void delay(unsigned int cnt) { while(--cnt); } /*--------------------------延時1ms程子程序-----------------------*/ void delay_1ms(uint z) { uint x,y; for(x=z;x>0;x--) for(y=126;y>0;y--); } /*--------------------------延時1ms程子程序-----------------------*/ delay1000() { uchar i,j; i=5; do{j=95; do{j--;} while(j); i--; } while(i); } /*---------------------------延時882us子程序-----------------------*/ delay882() { uchar i,j; i=6; do{j=71; do{j--;} while(j); i--; }while(i); } /*--------------------------延時2400us程子程序-----------------------*/ delay2400() { uchar i,j; i=5; do{j=237; do{j--;} while(j); i--; }while(i); } /**********************************************************************/ /* void display() { uchar i; for(i=0;i<8;i++) { P0=dofly[disp_date%10];//取顯示數據，段碼 P2=seg[i]; //取位碼 delay_1ms(1); disp_date/=10; } } */ /*********************************************************************/ uchar EEPROM_read(uint addr)//EEPROM字節讀 { ISP_CONTR=0x83; //系統時鐘<12M時，對ISP_CONTR寄存器設置的值，本電路為11.0592M ISP_CMD=1; //字節讀 ISP_ADDRH=(addr&0xff00)>>8; ISP_ADDRL=addr&0x00ff; ISP_TRIG=0x46; ISP_TRIG=0xb9; _nop_(); _nop_(); return ISP_DATA; } //-------------------------------------------------------------------- void EEPROM_write(uint addr,uchar dat)//EEPROM字節寫 { ISP_CONTR=0x83; //系統時鐘<12M時，對ISP_CONTR寄存器設置的值，本電路為11.0592M ISP_CMD=2; //字節編程 ISP_ADDRH=(addr&0xff00)>>8; ISP_ADDRL=addr&0x00ff; ISP_DATA=dat; ISP_TRIG=0x46; ISP_TRIG=0xb9; _nop_(); _nop_(); } //-------------------------------------------------------------------- void EEPROM_ERASE(uint addr)//EEPROM扇區擦除 { ISP_CONTR=0x83; //系統時鐘<12M時，對ISP_CONTR寄存器設置的值，本電路為11.0592M ISP_CMD=3; //扇區擦除 ISP_ADDRH=(addr&0xff00)>>8; ISP_ADDRL=addr&0x00ff; ISP_TRIG=0x46; ISP_TRIG=0xb9; _nop_(); _nop_(); } //************************************************************** /*----------------------------------------------------------*/ /*-----------------------紅外解碼程序(核心)-----------------*/ /*----------------------------------------------------------*/ void IR_decode() { uchar i,j; while(IR_RE==0); delay2400(); if(IR_RE==1) //延時2.4ms后如果是高電平則是新碼 { delay1000(); delay1000(); for(i=0;i<4;i++) { for(j=0;j<8;j++) { while(IR_RE==0); //等待地址碼第1位高電平到來 delay882(); //延時882us判斷此時引腳電平 ///CY=IR_RE; if(IR_RE==0) { date[i]>>=1; date[i]=date[i]|0x00; } else if(IR_RE==1) { delay1000(); date[i]>>=1; date[i]=date[i]|0x80; } } //1位數據接收結束 } //32位二進制碼接收結束 } } /* void LED_PWM() { lade_2=num; //384 lade_4=num; //384 while(lade_2!=0&Flag2==1) { for(lade_3=512;lade_3>lade_4;lade_3--) //512 { led_port=0x00; delay(1); } lade_3=512; //512 lade_4--; for(lade_1=0;lade_1<lade_2;lade_1++) { led_port=0x38; //c7 delay(1); } lade_1=0; lade_2--; if(temp!=0x0c&Flag2==1) { lade_2=0; } lade_2=num; //384 lade_4=num; //384 } } */ void calc() { EEPROM_read(0x2000); ee_temp1=ISP_DATA; ee_temp=ee_temp1&0x0f; //************************************* 1 /* if(date[3]==0xff&Flag2==1) { if(num>=20) { num=num-80; } //else num=1; LED_PWM(); } if(date[3]==0xfe&Flag2==1) { if(num<=500) { num=num+80; } // else num=511; LED_PWM(); } if(ee_temp1==0xfd) { led_port=0x00; watchdog_timer(); } if(ee_temp1==0xfc) { led_port=0x00; led_r=1; led_g=1; led_b=1; watchdog_timer(); } */ //********************************************** 2 if(ee_temp1==0xfb) { led_port=0x00; led_r=1; watchdog_timer(); } if(ee_temp1==0xfa) { led_port=0x00; led_g=1; watchdog_timer(); } if(ee_temp1==0xf9) { led_port=0x00; led_b=1; watchdog_timer(); } if(ee_temp1==0xf8) { led_port=0x00; led_r=1; led_g=1; led_b=1; watchdog_timer(); } //************************************** 3 if(ee_temp1==0xf7) { uint fade_1,fade_2,fade_3,fade_4; fade_2=448; //384 fade_4=448; //384 while(fade_2!=0&ee_temp==0x07) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x10; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x08; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x07) { fade_2=0; } watchdog_timer(); fade_2=448; //384 fade_4=448; //384 } } if(ee_temp1==0xf6) { uint fade_1,fade_2,fade_3,fade_4; fade_2=448; //384 fade_4=448; //384 while(fade_2!=0&ee_temp==0x06) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x20; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x10; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x06) { fade_2=0; } watchdog_timer(); fade_2=448; //384 fade_4=448; //384 } } if(ee_temp1==0xf5) { uint fade_1,fade_2,fade_3,fade_4; fade_2=448; //384 fade_4=448; //384 while(fade_2!=0&ee_temp==0x05) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x08; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x20; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x05) { fade_2=0; } watchdog_timer(); fade_2=448; //384 fade_4=448; //384 } } if(ee_temp1==0xf4) { while(ee_temp==4) { led_port=0x00; led_r=1; delay_1ms(200); led_port=0x00; led_r=1; led_g=1; delay_1ms(200); led_port=0x00; led_g=1; delay_1ms(200); watchdog_timer(); led_port=0x00; led_g=1; led_b=1; delay_1ms(200); led_port=0x00; led_b=1; delay_1ms(200); led_port=0x00; led_b=1; led_r=1; delay_1ms(200); watchdog_timer(); } } //************************************** 4 if(ee_temp1==0xf3) { uint fade_1,fade_2,fade_3,fade_4; fade_2=416; //384 fade_4=416; //384 while(fade_2!=0&ee_temp==0x03) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x10; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x08; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x03) { fade_2=0; } watchdog_timer(); fade_2=416; //384 fade_4=416; //384 } } if(ee_temp1==0xf2) { uint fade_1,fade_2,fade_3,fade_4; fade_2=384; //384 fade_4=384; //384 while(fade_2!=0&ee_temp==0x02) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x20; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x10; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x02) { fade_2=0; } watchdog_timer(); fade_2=384; //384 fade_4=384; //384 } } if(ee_temp1==0xf1) { uint fade_1,fade_2,fade_3,fade_4; fade_2=348; //384 fade_4=348; //384 while(fade_2!=0&ee_temp==0x01) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x08; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x20; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x01) { fade_2=0; } watchdog_timer(); fade_2=348; //384 fade_4=348; //384 } } if(ee_temp1==0xf0) { while(ee_temp==0) { led_port=0x00; led_r=1; delay_1ms(500); watchdog_timer(); led_port=0x00; led_g=1; delay_1ms(500); led_port=0x00; led_b=1; delay_1ms(500); watchdog_timer(); } } //******************************************** 5 if(ee_temp1==0xef) { uint fade_1,fade_2,fade_3,fade_4; fade_2=384; //384 fade_4=384; //384 while(fade_2!=0&ee_temp==0x0f) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x10; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x08; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x0f) { fade_2=0; } watchdog_timer(); fade_2=384; //384 fade_4=384; //384 } } if(ee_temp1==0xee) { uint fade_1,fade_2,fade_3,fade_4; fade_2=320; //384 fade_4=320; //384 while(fade_2!=0&ee_temp==0x0e) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x20; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x10; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x0e) { fade_2=0; } watchdog_timer(); fade_2=320; //384 fade_4=320; //384 } } if(ee_temp1==0xed) { uint fade_1,fade_2,fade_3,fade_4; fade_2=320; //384 fade_4=320; //384 while(fade_2!=0&ee_temp==0x0d) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x08; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x20; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x0d) { fade_2=0; } watchdog_timer(); fade_2=320; //384 fade_4=320; //384 } } if(ee_temp1==0xec) fade(); //******************************************* 6 if(ee_temp1==0xeb) { led_port=0x00; led_r=1; led_g=1; watchdog_timer(); } if(ee_temp1==0xea) { led_port=0x00; //led_r=0; led_g=1; led_b=1; watchdog_timer(); } if(ee_temp1==0xe9) { led_port=0x00; led_r=1; //led_g=0; led_b=1; watchdog_timer(); } if(ee_temp1==0xe8) fade1(); } void fade() { // uchar i; uint fade_1,fade_2,fade_3,fade_4; fade_2=512; fade_4=511; while(fade_2!=0&ee_temp==0x0c) { for(fade_3=512;fade_3>fade_4;fade_3--) { led_port=0x10; delay(1); } fade_3=512; fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x08; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x0c) { fade_2=0; } } watchdog_timer(); fade_2=512; fade_4=511; while(fade_2!=0&ee_temp==0x0c) { if(ee_temp!=0x0c) { fade_2=0; } for(fade_3=512;fade_3>fade_4;fade_3--) { led_port=0x20; delay(1); // watchdog_timer(); } fade_3=512; fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x10; delay(1); // watchdog_timer(); } fade_1=0; fade_2--; } watchdog_timer(); fade_2=512; fade_4=511; while(fade_2!=0&ee_temp==0x0c) { if(ee_temp!=0x0c) { fade_2=0; } for(fade_3=512;fade_3>fade_4;fade_3--) { led_port=0x08; delay(1); watchdog_timer(); } fade_3=512; fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x20; delay(1); watchdog_timer(); } fade_1=0; fade_2--; } watchdog_timer(); } void fade1() { // uchar i; uint fade_1,fade_2,fade_3,fade_4; fade_2=128; fade_4=127; while(fade_2!=0&ee_temp==0x08) { for(fade_3=128;fade_3>fade_4;fade_3--) { led_port=0x10; delay(1); } fade_3=128; fade_4--; for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x08; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x08) { fade_2=0; } } watchdog_timer(); fade_2=128; fade_4=127; while(fade_2!=0&ee_temp==0x08) { if(ee_temp!=0x08) { fade_2=0; } for(fade_3=128;fade_3>fade_4;fade_3--) { led_port=0x20; delay(1); } fade_3=128; fade_4--; for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x10; delay(1); } fade_1=0; fade_2--; } watchdog_timer(); fade_2=128; fade_4=127; while(fade_2!=0&ee_temp==0x08) { if(ee_temp!=0x08) { fade_2=0; } for(fade_3=128;fade_3>fade_4;fade_3--) { led_port=0x08; delay(1); } fade_3=128; fade_4--; for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x20; delay(1); } fade_1=0; fade_2--; } watchdog_timer(); } void init() { led_port=0x00; /* led_r=1; delay_1ms(500); led_port=0x00; led_g=1; delay_1ms(500); led_port=0x00; led_b=1; delay_1ms(500); led_port=0x00; */ delay_1ms(2); WDT_CONTR=0x3f; delay_1ms(500); } //******************************** void main() { init(); Flag2=0; SP=0x60; //堆棧指針 EX0=1; //允許外部中斷0,用于檢測紅外遙控器按鍵 EA=1; num=255; while(1) { calc(); } } //******************************************************************** /*------------------------外部中斷0程序-------------------------*/ /*------------------主要用于處理紅外遙控鍵值--------------------*/ void int0() interrupt 0 { uchar i; Flag2=0; /////// k=0; EX0=0; //檢測到有效信號關中斷，防止干擾 for(i=0;i<4;i++) { delay1000(); if(IR_RE==1){k=1;} //剛開始為9ms的引導碼. } led_port=0x00; if(k==0) { IR_decode(); //如果接收到的是有效信號，則調用解碼程序 if(date[3]>=0xe8) { if(date[3]<=0xfb) { temp1=date[3]; EEPROM_ERASE(0x2000); //STC_EEROM_0X2000 temp1 EEPROM_write(0x2000,temp1); EEPROM_read(0x2000); ee_temp1=ISP_DATA; ee_temp=ee_temp1&0x0f; /* temp=date[3]&0x0f; EEPROM_ERASE(0x2004); //STC_EEROM_0X2004 temp EEPROM_write(0x2004,temp); */ } else { EEPROM_read(0x2000); ee_temp1=ISP_DATA; ee_temp=ee_temp1&0x0f; } } delay2400(); delay2400(); delay2400(); delay_1ms(500); } EX0=1; //開外部中斷，允許新的遙控按鍵 }
上傳時間： 2016-07-02
上傳用戶：184890962
/*#include<reg52.h> #define uint unsigned int #define uchar unsigned char #define uchar unsigned char sbit K1=P3^4; sbit K2=P3^5; sbit ledr=P1^0; sbit ledg=P1^1; sbit ledb=P1^2; bit LEDDirection=0;//LED控制方向0：漸亮1：漸滅 char pwm=0; char pwmr=0; char scw=0;//中斷記數 char tt=0; char n; void dealy(uint z); void Timer0Init(void) { TMOD=0x01; TH0=0xff; TL0=0x47; EX0=1; IT0=0; PX0=1; ET0=1; TR0=1; EA=1; } void main() { Timer0Init(); while(1){ if(K1==0) { dealy (1); if(K1==0) {TR0=1; ledr=0; dealy(5); TR0=0; } } if(K2==0) { dealy (1); if(K2==0) { while(1) { ledr=0; //亮 dealy(100-n*10); ledr=1; //熄 dealy(n*10); } } } } } void Time0Isr(void) interrupt 1 { // pwm=0; TH0=0xff; TL0=0x47; scw++; }*/ #include<reg52.h> #define uchar unsigned char bit LEDDirection=0; sbit P2_0=P1^0; sbit key1=P3^4; sbit key2=P3^5; sbit key3=P3^6; uchar zkb,i,t;// zkb指占空比 uchar pwm; void delay(uchar z) { uchar x,y; for(x=z;x>0;x--) for(y=110;y>0;y--); } void init() //初始化函數 { TMOD=0X01; TH0=(65536-1000)/256; TL0=(65536-1000)%256; EA=1; ET0=1; TR0=1; } void keyscan() //鍵盤掃描 { P3=0XFF; if(key1==0) { delay(5); if(key1==0) { while(!key1); if(zkb<9) { zkb++; } } } if(key2==0) { delay(5); if(key2==0) { while(!key2); if(zkb>0) { zkb--; } } } if(key3==0) {TR0=1; delay(5); if(key3==0) {while(!key3); if((zkb<=9)&&(0==LEDDirection)) { zkb++; if(zkb>9) { LEDDirection=1; zkb=9; } } if((zkb>=0 )&&(1==LEDDirection)) { zkb--; if(zkb<0 ) { LEDDirection=0; zkb=0 ; //dealy(3000); } } } //pwm=pwmr; } } void main() //主函數 { zkb=2; init(); while(1) { keyscan(); } } void time0(void) interrupt 1 //中斷函數 { TH0=(65536-200)/256; TL0=(65536-200)%256; ++i; if(i>10) { i=0; }; if(i<=zkb) { P2_0=1; } else P2_0=0; } /*void time0(void) interrupt 0 //中斷函數 { TH0=(65536-1000)/256; TL0=(65536-1000)%256; ++i; if(i>10) { i=0; }; if(i<=zkb) { P2_0=1; } else P2_0=0; }*/
標簽： 調光
上傳時間： 2016-07-02
上傳用戶：184890962
# include < reg52.h > # include < 24C02.h> # define uint unsigned int # define uchar unsigned char sbit rs = P3^5; //定義lcd1602的rs端 sbit lcden = P3^4;//定義lcd1602的lcden端口 sbit s1 = P3^0;//定義功能鍵s1 sbit s2 = P3^1;//定義功能鍵s2 sbit s3 = P3^2;//定義功能鍵s3 sbit beep = P2^3;//定義蜂鳴器 uchar count, s1num; char miao,fen,shi; uchar code table[] = "Designer:X_ZL ";//定義初始上電時液晶默認顯示狀態 void delay_ms( xms ) //定義延時函數 { uint i,j; for( i = xms ; i > 0 ; i --) for( j = 110 ; j > 0 ; j --); }
上傳時間： 2016-07-28
上傳用戶：游戲好嗎
ARINC429總線協議是美國航空電子工程委員會(Airlines Engineering Committee)于1977年7月提出的，并于同年發表并獲得批準使用，它的全稱是數字式信息傳輸系統(Digital Information Transmission System ) 。協議標準規定了航空電子設備及有關系統間的數字信息傳輸要求。ARINC429廣泛應用在先進的民航客機中，如B-737、B-757、B-767，俄制軍用飛機也選用了類似的技術。 ARINC429總線結構簡單、性能穩定，抗干擾性強。最大的優勢在于可靠性高。飛機上的ARINC429數據總線，用于在系統和設備之間傳送上千種不同類型的參數，如航向、真空速、馬赫數等。
標簽： 429總線協議
上傳時間： 2016-08-17
上傳用戶：w50403
基礎程序設計 01 閃爍的LED /* 名稱閃爍的LED 說明LED按設定的時間間隔閃爍 */ #include<reg51.h> #define uchar unsigned char #define uint unsigned int sbit LED=P1^0; //延時 void DelayMS(uint x) { uchar i; while(x--) { for(i=0;i<120;i++); } } //主程序 void main() { while(1) { LED=~LED; DelayMS(150); } }
標簽： 基于8051仿真 基于Proteus仿真 基于8051+Proteus仿真
上傳時間： 2016-09-19
上傳用戶：xinhoujue
基礎程序設計 01 閃爍的LED /* 名稱閃爍的LED 說明LED按設定的時間間隔閃爍 */ #include<reg51.h> #define uchar unsigned char #define uint unsigned int sbit LED=P1^0; //延時 void DelayMS(uint x) { uchar i; while(x--) { for(i=0;i<120;i++); } } //主程序 void main() { while(1) { LED=~LED; DelayMS(150); } }
標簽： 51單片機C語言程序設計 51單片機C語言程序設計Proteus仿真實訓
上傳時間： 2016-09-19
上傳用戶：xinhoujue
#include <malloc.h> #include <stdio.h> #include <stdlib.h> #include <string.h> #define NULL 0 #define MaxSize 30 typedef struct athletestruct /*運動員*/ { char name[20]; int score; /*分數*/ int range; /**/ int item; /*項目*/ }ATH; typedef struct schoolstruct /*學校*/ { int count; /*編號*/ int serial; /**/ int menscore; /*男選手分數*/ int womenscore; /*女選手分數*/ int totalscore; /*總分*/ ATH athlete[MaxSize]; /**/ struct schoolstruct *next; }SCH; int nsc,msp,wsp; int ntsp; int i,j; int overgame; int serial,range; int n; SCH *head,*pfirst,*psecond; int *phead=NULL,*pafirst=NULL,*pasecond=NULL; void create(); void input () { char answer; head = (SCH *)malloc(sizeof(SCH)); /**/ head->next = NULL; pfirst = head; answer = 'y'; while ( answer == 'y' ) { Is_Game_DoMain: printf("\nGET Top 5 when odd\nGET Top 3 when even"); printf("\n輸入運動項目序號 (x<=%d):",ntsp); scanf("%d",pafirst); overgame = *pafirst; if ( pafirst != phead ) { for ( pasecond = phead ; pasecond < pafirst ; pasecond ++ ) { if ( overgame == *pasecond ) { printf("\n這個項目已經存在請選擇其他的數字\n"); goto Is_Game_DoMain; } } } pafirst = pafirst + 1; if ( overgame > ntsp ) { printf("\n項目不存在"); printf("\n請重新輸入"); goto Is_Game_DoMain; } switch ( overgame%2 ) { case 0: n = 3;break; case 1: n = 5;break; } for ( i = 1 ; i <= n ; i++ ) { Is_Serial_DoMain: printf("\n輸入序號 of the NO.%d (0<x<=%d): ",i,nsc); scanf("%d",&serial); if ( serial > nsc ) { printf("\n超過學校數目,請重新輸入"); goto Is_Serial_DoMain; } if ( head->next == NULL ) { create(); } psecond = head->next ; while ( psecond != NULL ) { if ( psecond->serial == serial ) { pfirst = psecond; pfirst->count = pfirst->count + 1; goto Store_Data; } else { psecond = psecond->next; } } create(); Store_Data: pfirst->athlete[pfirst->count].item = overgame; pfirst->athlete[pfirst->count].range = i; pfirst->serial = serial; printf("Input name:) : "); scanf("%s",pfirst->athlete[pfirst->count].name); } printf("\n繼續輸入運動項目(y&n)？"); answer = getchar(); printf("\n"); } } void calculate() /**/ { pfirst = head->next; while ( pfirst->next != NULL ) { for (i=1;i<=pfirst->count;i++) { if ( pfirst->athlete[i].item % 2 == 0 ) { switch (pfirst->athlete[i].range) { case 1:pfirst->athlete[i].score = 5;break; case 2:pfirst->athlete[i].score = 3;break; case 3:pfirst->athlete[i].score = 2;break; } } else { switch (pfirst->athlete[i].range) { case 1:pfirst->athlete[i].score = 7;break; case 2:pfirst->athlete[i].score = 5;break; case 3:pfirst->athlete[i].score = 3;break; case 4:pfirst->athlete[i].score = 2;break; case 5:pfirst->athlete[i].score = 1;break; } } if ( pfirst->athlete[i].item <=msp ) { pfirst->menscore = pfirst->menscore + pfirst->athlete[i].score; } else { pfirst->womenscore = pfirst->womenscore + pfirst->athlete[i].score; } } pfirst->totalscore = pfirst->menscore + pfirst->womenscore; pfirst = pfirst->next; } } void output() { pfirst = head->next; psecond = head->next; while ( pfirst->next != NULL ) { // clrscr(); printf("\n第%d號學校的結果成績:",pfirst->serial); printf("\n\n項目的數目\t學校的名字\t分數"); for (i=1;i<=ntsp;i++) { for (j=1;j<=pfirst->count;j++) { if ( pfirst->athlete[j].item == i ) { printf("\n %d\t\t\t\t\t\t%s\n %d",i,pfirst->athlete[j].name,pfirst->athlete[j].score);break; } } } printf("\n\n\n\t\t\t\t\t\t按任意建 進入下一頁"); getchar(); pfirst = pfirst->next; } // clrscr(); printf("\n運動會結果:\n\n學校編號\t男運動員成績\t女運動員成績\t總分"); pfirst = head->next; while ( pfirst->next != NULL ) { printf("\n %d\t\t %d\t\t %d\t\t %d",pfirst->serial,pfirst->menscore,pfirst->womenscore,pfirst->totalscore); pfirst = pfirst->next; } printf("\n\n\n\t\t\t\t\t\t\t按任意建結束"); getchar(); } void create() { pfirst = (struct schoolstruct *)malloc(sizeof(struct schoolstruct)); pfirst->next = head->next ; head->next = pfirst ; pfirst->count = 1; pfirst->menscore = 0; pfirst->womenscore = 0; pfirst->totalscore = 0; } void Save() {FILE *fp; if((fp = fopen("school.dat","wb"))==NULL) {printf("can't open school.dat\n"); fclose(fp); return; } fwrite(pfirst,sizeof(SCH),10,fp); fclose(fp); printf("文件已經成功保存\n"); } void main() { system("cls"); printf("\n\t\t\t 運動會分數統計\n"); printf("輸入學校數目 (x>= 5):"); scanf("%d",&nsc); printf("輸入男選手的項目(x<=20):"); scanf("%d",&msp); printf("輸入女選手項目(<=20):"); scanf("%d",&wsp); ntsp = msp + wsp; phead = (int *)calloc(ntsp,sizeof(int)); pafirst = phead; pasecond = phead; input(); calculate(); output(); Save(); }
標簽： 源代碼
上傳時間： 2016-12-28
上傳用戶：150501
