亚洲欧美第一页_禁久久精品乱码_粉嫩av一区二区三区免费野_久草精品视频

基于單片機的數字化B超鍵盤設計

針對目前使用的RS232接口數字化B超鍵盤存在PC主機啟動時不能設置BIOS，提出一種PS2鍵盤的設計方法。基于W78E052D單片機，采用8通道串行A/D轉換器設計了8個TGC電位器信息采集電路，電位器位置信息以鍵盤掃描碼序列形式發送，正交編碼器信號通過XC9536XL轉換為單片機可接收的中斷信號，軟件接收到中斷信息后等效處理成按鍵。結果表明，在滿足開機可設置BIOS同時，又可實現超聲特有功能，不需要專門設計驅動程序，接口簡單，成本低。 Abstract:  Aiming at the problem of the digital ultrasonic diagnostic imaging system keyboard with RS232 interface currently used couldn?蒺t set the BIOS when the PC boot， this paper proposed a design method of PS2 keyboards. Based on W78E052D microcontroller，designed eight TGC potentiometers information acquisition circuit with 8-channel serial A/D converter， potentiometer position information sent out with keyboard scan code sequentially.The control circuit based on XC9536 CPLD is used for converting the mechanical actions of the encoders into the signals that can be identified by the MCU， software received interrupt information and equivalently treatmented as key. The results show that the BIOS can be set to meet the boot， ultrasound specific functionality can be achieved at the same time， it does not require specially designed driver，the interface is simple and low cost.    

標簽： 單片機 B超 數字化 鍵盤設計

上傳時間： 2013-10-10

上傳用戶：asdfasdfd

TKS仿真器B系列快速入門

TKS仿真器B系列快速入門

標簽： TKS 仿真器 快速入門

上傳時間： 2013-10-31

上傳用戶：aix008

NCV7356單線CANBUS收發器數據手冊

The NCV7356 is a physical layer device for a single wire data linkcapable of operating with various Carrier Sense Multiple Accesswith Collision Resolution (CSMA/CR) protocols such as the BoschController Area Network (CAN) version 2.0. This serial data linknetwork is intended for use in applications where high data rate is notrequired and a lower data rate can achieve cost reductions in both thephysical media components and in the microprocessor and/ordedicated logic devices which use the network.The network shall be able to operate in either the normal data ratemode or a high-speed data download mode for assembly line andservice data transfer operations. The high-speed mode is onlyintended to be operational when the bus is attached to an off-boardservice node. This node shall provide temporary bus electrical loadswhich facilitate higher speed operation. Such temporary loads shouldbe removed when not performing download operations.The bit rate for normal communications is typically 33 kbit/s, forhigh-speed transmissions like described above a typical bit rate of83 kbit/s is recommended. The NCV7356 features undervoltagelockout, timeout for faulty blocked input signals, output blankingtime in case of bus ringing and a very low sleep mode current.

標簽： CANBUS 7356 NCV 單線

上傳時間： 2013-10-24

上傳用戶：s藍莓汁

一個簡單好用的B+樹算法實現

一個簡單好用的B+樹算法實現

標簽： 樹 算法

上傳時間： 2015-01-04

上傳用戶：縹緲

一個用Basic實現的B-Tree算法

一個用Basic實現的B-Tree算法

標簽： B-Tree Basic 算法

上傳時間： 2013-12-30

上傳用戶：ccclll

一個用Java applet實現的B-Tree算法

一個用Java applet實現的B-Tree算法

標簽： B-Tree applet Java 算法

上傳時間： 2013-12-25

上傳用戶：qiao8960

用C++實現的B-Tree算法

用C++實現的B-Tree算法

標簽： B-Tree 算法

上傳時間： 2014-01-20

上傳用戶：jiahao131

用Borland C寫的B-Tree算法

用Borland C寫的B-Tree算法

標簽： Borland B-Tree 算法

上傳時間： 2014-12-05

上傳用戶：xzt

《3D Engine Design》的隨書源代碼