The MAX481E, MAX483E, MAX485E, MAX487E–MAX491E, and MAX1487E are low-power transceivers for RS-485 and RS-422 communications in harsh environments. Each driver output and receiver input is protected against ±15kV electrostatic discharge (ESD) shocks, without latchup. These parts contain one driver and one receiver. The MAX483E, MAX487E, MAX488E, and MAX489E feature reduced slewrate drivers that minimize EMI and reduce reflections caused by improperly terminated cables, thus allowing error-free data transmission up to 250kbps. The driver slew rates of the MAX481E, MAX485E, MAX490E, MAX491E, and MAX1487E are not limited, allowing them to transmit up to 2.5Mbps.
標簽： MAX transceivers 485 low-power
上傳時間： 2013-12-22
上傳用戶：小寶愛考拉
CyberCart Pro Internet Commerce System 3.042 很好的商業購物程序.Good Shopping Cart, Can be used for Multiple Clients or Storefronts or Web Mall
標簽： CyberCart Commerce Internet Shopping
上傳時間： 2016-10-29
上傳用戶：duoshen1989
數據加密程序 p macro buf lea dx,buf mov ah,9 int 21h endm data segment pp db 0dh,0ah, welcome you to run this programme!$ qq db 0dh,0ah, when you input number,press enter.$ qw db 0dh,0ah, 6eh,52h,94h,52h,$ qa db 0dh,0ah, $ info1 db 0dh,0ah,0dh, input number:$ info2 db 0dh,0ah, output number:$ bufa db 20
上傳時間： 2013-12-24
上傳用戶：離殤
A Module-based Wireless Node (MW-Node) is a Node with wireless and mobile capabilities added by means of modules. It is not a new node object derived from Node. Rather it is a new layout of mostly existing components. Rationale for this new design has been presented in [1]. The MW-Node provides a flexible support for wireless and mobile networking and in particular: support for multiple interfaces/multiple channels, and a common basis for the implementation of wireless routing protocols.
標簽： Node Module-based capabilities Wireless
上傳時間： 2013-12-26
上傳用戶：大三三
Snefru is a cryptographic hash function invented by Ralph Merkle which supports 128-bit and 256-bit output.
標簽： cryptographic bit function invented
上傳時間： 2014-01-13
上傳用戶：wang0123456789
Top module name : SHIFTER (File name : SHIFTER.v) 2. Input pins: SHIFT [3:0], IN [15:0], SIGN, RIGHT. 3. Output pins: OUT [15:0]. 4. Input signals generated from test pattern are latched in one cycle and are synchronized at clock rising edge. 5. The SHIFT signal describes the shift number. The shift range is 0 to 15. 6. When the signal RIGHT is high, it shifts input data to right. On the other hand, it shifts input data to left. 7. When the signal SIGN is high, the input data is a signed number and it shifts with sign extension. However, the input data is an unsigned number if the signal SIGN is low. 8. You can only use following gates in Table I and need to include the delay information (Tplh, Tphl) in your design.
上傳時間： 2013-12-13
上傳用戶：himbly
Top module name : SHIFTER (File name : SHIFTER.v) 2. Input pins: SHIFT [3:0], IN [15:0], SIGN, RIGHT. 3. Output pins: OUT [15:0]. 4. Input signals generated from test pattern are latched in one cycle and are synchronized at clock rising edge. 5. The SHIFT signal describes the shift number. The shift range is 0 to 15. 6. When the signal RIGHT is high, it shifts input data to right. On the other hand, it shifts input data to left. 7. When the signal SIGN is high, the input data is a signed number and it shifts with sign extension. However, the input data is an unsigned number if the signal SIGN is low. 8. You can only use following gates in Table I and need to include the delay information (Tplh, Tphl) in your design.
上傳時間： 2014-01-20
上傳用戶：三人用菜
a Java program that reads in the following values from the standard input device (i.e. Keyboard) and writes its result on the standard output device (i.e. Console/Monitor): Inputs: A: the loan amount in dollars and cents (e.g. 150000.00). r: the net annual interest rate, expressed as an integer (e.g. 10 which means 10％) Y: the number of whole remaining years (for repayment) M: the number of remaining months Output: The program should calculate and output the amount of monthly repayments in dollars and cents as single value (e.g. $840.55)
標簽： i.e. following the Keyboard
上傳時間： 2013-12-15
上傳用戶：米卡
Produce Java classes to calculate and display the Poisson probability when input the value of the average (A) arrival rate of customers at some business in the range of 1 to 10. The error message will output when A is out of the range。
標簽： the probability calculate Produce
上傳時間： 2014-01-10
上傳用戶：moerwang
This code in this directory implements the binary hopfield network.Source code may be found in HOPNET.CPP. A sample training file is H7x8N4.trn. Sample test pattern files are: H7x8D4.TST, H5x8D7.TST,H5x8D7.TST and H5x8D9.TST, Output of the program goes to both the screen and a file, ARCHIVE.LST.
標簽： code implements directory hopfield
上傳時間： 2013-12-27
上傳用戶：ruixue198909
