OPTOELECTRONICS CIRCUIT COLLECTION
AVALANCHE PHOTODIODE BIAS SUPPLY 1Provides an output voltage of 0V to +80V for reverse biasingan avalanche photodiode to control its gain. This circuit canalso be reconfigured to supply a 0V to –80V output.LINEAR TEC DRIVER–1This is a bridge-tied load (BTL) linear amplifier for drivinga thermoelectric cooler (TEC). It operates on a single +5Vsupply and can drive ±2A into a common TEC.LINEAR TEC DRIVER–2This is very similar to DRIVER–1 but its power output stagewas modified to operate from a single +3.3V supply in orderto increase its efficiency. Driving this amplifier from astandard +2.5V referenced signal causes the output transistorsto have unequal power dissipation.LINEAR TEC DRIVER–3This BTL TEC driver power output stage achieves very highefficiency by swinging very close to its supply rails, ±2.5V.This driver can also drive ±2A into a common TEC. Operationis shown with the power output stage operating on±1.5V supplies. Under these conditions, this linear amplifiercan achieve very high efficiency.
Application ReportThe following collection of analog circuits may be useful in electro-optics applications such as optical networkingsystems. This page summarizes their salient characteristics.
Linear Technology’s high performance battery management ICsenable long battery life and run time, while providing precision charging control, constantstatus monitoring and stringent battery protection. Our proprietary design techniques seamlesslymanage multiple input sources while providing small solution footprints, faster charging and100% standalone operation. Battery and circuit protection features enable improved thermalperformance and high reliability operation.
Abstract: This document details the Lakewood (MAXREFDES7#) subsystem reference design, a 3.3V input, ±12V (±15V) output, isolated power supply. The Lakewood reference design includes a 3W primary-side transformer H-bridge driver for isolated supplies, and two wide input range and adjustable output low-dropout linear regulators (LDOs). Test results and hardware files are included.
Abstract: This document details the Riverside (MAXREFDES8#) subsystem reference design, a 3.3V input, 12V (15V) output, isolated power supply. The Riverside reference design includes a 3W primary-side transformer H-bridge driver for isolated supplies, and one wide input range and adjustable output low-dropout linear regulator (LDO). Test results and hardware files are included.
交流瓦特/瓦特小時，乏爾/乏爾小時轉換器 特點： 精確度0.25%滿刻度 多種輸入,輸出選擇 輸入與輸出絕緣耐壓2仟伏特/1分鐘 沖擊電壓測試5仟伏特(1.2x50us) 突波電壓測試2.5仟伏特(0.25ms/1MHz) (IEC255-4) 尺寸小，穩定性高 主要規格： 精確度: 0.25% F.S. (23 ±5℃) 輸入負載: <0.2VA (Voltage) <0.2VA (Current) 最大過載能力: Current related input:3 x rated continuous 10 x rated 30 sec. ,25 x rated 3sec. 50 x rated 1sec. Voltage related input:maximum 2 x rated continuous 輸出反應速度: < 250ms(0~90%) 輸出負載能力: < 10mA for voltage mode < 10V for current mode 輸出之漣波 : < 0.1% F.S. 脈波輸出型態: Photocouple of open collector (max.30V/40mA) 歸零調整范圍: 0~±5% F.S. 最大值調整范圍: 0~±10% F.S. 溫度系數: 100ppm/℃ (0~50℃) 隔離特性: Input/Output/Power/Case 絕緣阻抗: >100Mohm with 500V DC 絕緣耐壓能力: 2KVac/1 min. (input/output/power/case) 突波測試: ANSI C37.90a/1974,DIN-IEC 255-4 impulse voltage 5KV(1.2x50us) 使用環境條件: -20~60℃(20 to 90% RH non-condensed) 存放環境條件: -30~70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
Abstract: Rail splitting is creating an artificial virtual ground as a reference voltage. It is used to set the signalto match the op amp's "sweet spot." An op amp has the most linear- and distortion-free qualities at that sweetspot. Typically, the sweet spot occurs near the center between the single power rail and ground. In the case ofa number of signals, the virtual ground can control channel DC errors when multiplexing or switching thesignals.
The CN3052A is a complete constant-current /constant voltage linear charger for single cell Li-ion and Li Polymer rechargeable batteries. The device contains an on-chip power MOSFET and eliminates the need for the external sense resistor and blocking diode.
The LT®1943 is a highly integrated, 4-output regulatordesigned to power large TFT LCD panels. The LT1943employs switching regulators—instead of linear regulators—to minimize power dissipation and accommodate awide input voltage range. The wide input range, 4.5V to22V, allows it to accept a variety of power sources,including the commonly used 5V, 12V and 19V AC adaptors.
Power over Ethernet (PoE) is a new development thatallows for the delivery of power to Ethernet-based devicesvia standard Ethernet CAT5 cable, precluding the need forwall adapters or other external power sources. The PoEspecification defines a hardware detection protocol wherePower Sourcing Equipment (PSE) is able to identify PoEPowered Devices (PDs), thus allowing full backwardscompatibility with non-PoE-aware (legacy) Ethernetdevices.
Linear Technology offers a variety of devices that simplifyconverting power from a USB cable, but the LTC®3455represents the highest level of functional integration yet. The LTC3455 seamlessly manages power flowbetween an AC adapter, USB cable and Li-ion battery,while complying with USB power standards, all from a4mm × 4mm QFN package. In addtion, two high efficiencysynchronous buck converters generate low voltage railswhich most USB-powered peripherals require. TheLTC3455 also provides power-on reset signals for themicroprocessor, a Hot SwapTM output for poweringmemory cards as well as an uncommitted gain blocksuitable for use as a low-battery comparator or an LDOcontroller. The PCB real estate required for the entire USBpower control circuit and two DC/DC converters is only225mm2.
