The PL2303 USB to Serial adapter is your smart and convenient accessory forconnecting RS-232 serial devices to your USB-equipped Windows host computer. Itprovides a bridge connection with a standard DB 9-pin male serial port connector inone end and a standard Type-A USB plug connector on the other end. You simplyattach the serial device onto the serial port of the cable and plug the USB connectorinto your PC USB port. It allows a simple and easy way of adding serial connectionsto your PC without having to go thru inserting a serial card and traditional portconfiguration.This USB to Serial adapter is ideal for connecting modems, cellular phones, PDAs,digital cameras, card readers and other serial devices to your computer. It providesserial connections up to 1Mbps of data transfer rate. And since USB does not requireany IRQ resource, more devices can be attached to the system without the previoushassles of device and resource conflicts.Finally, the PL-2303 USB to Serial adapter is a fully USB Specification compliantdevice and therefore supports advanced power management such as suspend andresume OPERATIONs as well as remote wakeup. The PL-2303 USB Serial cable adapteris designed to work on all Windows operating systems.
This application note explains the XC9500™/XL/XV Boundary Scan interface anddemonstrates the software available for programming and testing XC9500/XL/XV CPLDs. Anappendix summarizes the iMPACT software OPERATIONs and provides an overview of theadditional OPERATIONs supported by XC9500/XL/XV CPLDs for in-system programming.
The NCV7356 is a physical layer device for a single wire data linkcapable of operating with various Carrier Sense Multiple Accesswith Collision Resolution (CSMA/CR) protocols such as the BoschController Area Network (CAN) version 2.0. This serial data linknetwork is intended for use in applications where high data rate is notrequired and a lower data rate can achieve cost reductions in both thephysical media components and in the microprocessor and/ordedicated logic devices which use the network.The network shall be able to operate in either the normal data ratemode or a high-speed data download mode for assembly line andservice data transfer OPERATIONs. The high-speed mode is onlyintended to be operational when the bus is attached to an off-boardservice node. This node shall provide temporary bus electrical loadswhich facilitate higher speed operation. Such temporary loads shouldbe removed when not performing download OPERATIONs.The bit rate for normal communications is typically 33 kbit/s, forhigh-speed transmissions like described above a typical bit rate of83 kbit/s is recommended. The NCV7356 features undervoltagelockout, timeout for faulty blocked input signals, output blankingtime in case of bus ringing and a very low sleep mode current.
This application note explains the XC9500™/XL/XV Boundary Scan interface anddemonstrates the software available for programming and testing XC9500/XL/XV CPLDs. Anappendix summarizes the iMPACT software OPERATIONs and provides an overview of theadditional OPERATIONs supported by XC9500/XL/XV CPLDs for in-system programming.
This application note shows how a Xilinx CoolRunnerTM-II CPLD can be used as a simplelogical switch that can quickly and reliably select between different MPEG video sources. Thesource code for the design is available on the Xilinx website, and is linked from the “VHDLCode” section. The code can be expanded by the user to perform additional OPERATIONs usingthe remaining CPLD resources
IEEE1394Diag is a GUI application that presents a graphical view of an IEEE1394 network and provides the ability to perform common 1394 OPERATIONs such as async reads, writes, isoc listens and talks, as well as configuration rom browsing of all nodes present on a bus.
This article is a very simple introduction writing a Windows Form application for the
Microsoft.NET framework using C#. The sample application demonstrates how to create and
layout controls on a simple form and the handling of mouse click events. The application
displays a form showing attributes of a file. This form is similar to the properties dialog box of a
file (Right click on a file and Click on Properties menu item). Since attributes of a file will be
shown, the sample will show how to use File IO OPERATIONs in .NET framework.
This document describes the MPI and MPI standards They are both extensions
to the MPI standard The MPI part of the document contains clarications and
corrections to the MPI standard and denes MPI The MPI part of the document
describes additions to the MPI standard and denes MPI These include miscellaneous
topics process creation and management onesided communications extended collective
OPERATIONs external interfaces IO and additional language bindings
The decoding algorithm used in RBDS.c is based on error trapping. The program emulates the operation of the encoder and decoder of a binary cyclic codes, using bitwise shifts and xor for modulo g(x) OPERATIONs.
