在汽車發動機起動時，若發動機起動后起動機不能及時斷電，將會燒毀起動機或損壞飛輪齒環；若變速器不在空檔位置起動，則起動機的瞬間動力將使汽車位移，還可能引起交通事故和人身安全。為此介紹一種利用NXP P89LPC901單片機控制的汽車起動保護控制器，通過檢測汽車起動開關、變速箱檔位、發動機轉速，實現對汽車發動機起動過程檢測和保護。起動保護控制器在發動機起動過程中通過采用逐個關閉打開負載系統，解決汽車發動機過程中因起動電流大而對汽車電源的沖擊影響,延長了電瓶壽命。 Abstract: When the automotive engine is started, the engine start motor and flywheel gear may be damaged， even traffic accidents and personal safeties may be caused by wrong OPeration or other factors.In order to ensure the automotive engine can be started normally and safely,it is necessary that the protecting measures and methods are considered in the automotive electrical control system.This paper introduces a kind of the automotive engine starting protect controller based on NXP P89LPC901 MCU.The controller can protect the engine starting process by detecting the starter key switch,transmission stall and engine speed.Through the use of close and open load system,the controller can solve the impact on automotive power because of the high-current load in the process of the automobile engine starting, and extend battery life.
上傳時間： 2013-10-15
上傳用戶：mikesering
C8051F020單片機通過SPI接口驅動四線電阻式觸摸屏控制器TSC2046，利用中斷方式驅動TSC2046設計軟件。介紹了觸摸屏的工作原理、TSC2046工作方式以及典型應用電路。 Abstract: The C8051F020 MCU is connected with the TSC2046 which is a 4-wire touch screen controller. The TSC2046 is controlled by interrupt mode, the? OPeration principle of touch screen is introduced. The OPeration mode of TSC2046 and typical application circuit are also discussed.
上傳時間： 2014-12-27
上傳用戶：hwl453472107
提出了一種基于C8051F320的紅外模擬槍戰系統設計方案。介紹了紅外模擬槍戰系統的構成，給出了硬件選型、系統硬軟件設計。利用紅外抗對系統的工作原理，系統獲得良好效果。 Abstract: This paper presents the design of simulated gunfight system based on C8051F320.Introduces system structure,and puts forward hardware selection of infrared simulated gunfight system and system hardware and software designs.Using the OPeration principle of infrared antagonizing system,the system result is good.
上傳時間： 2013-11-20
上傳用戶：南國時代
介紹了MPC555與CS8900A擴展以太網的硬件設計圖。以NUCLUES PLUS操作系統為基礎，介紹了網卡軟件驅動程序的編制，給出了以太網協議包嵌入NUCLEUS PLUS操作系統的實現方法。 Abstract: The Ethernet extension hardware design of MPC555 and CS8900A are introduced,and the software driven program based on NUCLEUS PLUS OPeration system and the technique that Ethernet protocol embedded in NUCLEUS PLUS real OPeration system are discussed.
上傳時間： 2013-10-23
上傳用戶：xiehao13
介紹了電力操作電源與智能電池巡檢系統的特點，給出了一種基于超低功耗單片機MSP430 F149針對中小型變電站自動化運行的專用設備的基本設計原理及實現方法，最后給出了詳細硬件構成和軟件實現。該系統能滿足中小型變電站安全、可靠、自動運行的要求，并通過與上位機的串行通信實現變電站的遠程管理和控制。 Abstract: The characters of the intelligent battery data logging system of the electric OPeration power are introduced.The basic design principle and the implemented methods of the special equipment which only designed for the middle or small transformer substation based on MSP430F149 are prescribed. Finally, the hardware block diagram and the software flow chart are also given. The function that the system finally needs to realize can basically meet with the middle or small transformer substation’s satisfy, reliably,and automatic running.And it can also realize the transformer substation long-distance management and control by serial communicating with the host computer.
上傳時間： 2013-11-25
上傳用戶：黃華強
為降低成本和解決現有膜片鉗放大器系統中PC機的干擾問題，研究了一種基于單片機的膜片鉗放大器小系統。該系統采用ADI公司生產的ADuC841作為控制核心，并且配置相應的液晶顯示模塊LCM3202401。模擬電路部分采用高輸入阻抗的AD8627實現微電流信號的采集，并由后級電路進行信號的放大和電阻電容的補償。它具有硬件電路簡單、體積小、使用方便的特點。既可以單獨作為小系統實現采集和顯示，也可以通過紅外方式和PC機進行通訊，在PC機上進行信號的處理。 Abstract: In order to reduce cost and resolve the interferential problem with PC in existing patch clamp amplifiers, a small patch clamp amplifier system design based on microcontroller is studied. It adopts a new high performance microconverter ADuC841 by the ADI as the control core in the system, configuring a liquid crystal module LCM3202401. In the analog circuit, AD8627 with high input impedance is used to detect the low current，signal magnification, as well as resistance and capacitance compensation are accomplished by subsequent circuits. It has the advantage of simple hardware circuit design, small volume and convenient OPeration. It can either be used as an independent system to measure and show signal detected or transmit to PC by infrared ray.
上傳時間： 2013-11-06
上傳用戶：yy_cn
針對當前安檢力學試驗機所能完成的試驗種類單一、自動化程度低等問題，提出一種以ATmega128單片機為核心控制器的安檢力學試驗機的設計。詳細闡述了該安檢力學試驗機各個組成部分的設計原理和方案，并且給出了各部分的軟件設計思想和操作流程。經過大量測試試驗表明：設計的安檢力學試驗機可以完成多達十余種的力學安檢試驗，完全符合相關國家標準，并且具有數據采集精度高、傳輸速度快、操作安全簡便等特點，實現了安檢設備的多功能化、數字化和自動化。 Abstract: Currently， many mechanical security testing machines have only one function. The degree of automation of them is low. To solve those problems， a new kind of mechanical security testing machine， using ATmega128 micro-controller as its core controller， has been advanced. It describes the components of the machine. The principles and the scheme in the designing processes are presented in detail， and the software architecture and the OPeration processes of each part are given. After having done many testing， we have reached the following conclusions: the mechanical security testing machine presented can do over ten mechanical security tests complying with related national standards. It has high data acquisition accuracy and high transmission speed. The OPeration of the machine is simple and safe. In general， this machine is a multi-functional， highly automatic， digitalized security testing device.
上傳時間： 2013-11-05
上傳用戶：a67818601
The LPC1700 Ethernet block contains a full featured 10 Mbps or 100 Mbps Ethernet MAC (Media Access Controller) designed to provide optimized performance through the use of DMA hardware acceleration. Features include a generous suite of control registers, half or full duplex OPeration, flow control, control frames, hardware acceleration for transmit retry, receive packet filtering and wake-up on LAN activity. Automatic frame transmission and reception with Scatter-Gather DMA off-loads many OPerations from the CPU.
上傳時間： 2013-11-09
上傳用戶：geshaowei
The PCA9541 is a 2-to-1 I2C-bus master selector designed for high reliability dual masterI2C-bus applications where system OPeration is required, even when one master fails orthe controller card is removed for maintenance. The two masters (for example, primaryand back-up) are located on separate I2C-buses that connect to the same downstreamI2C-bus slave devices. I2C-bus commands are sent by either I2C-bus master and are usedto select one master at a time. Either master at any time can gain control of the slavedevices if the other master is disabled or removed from the system. The failed master isisolated from the system and will not affect communication between the on-line masterand the slave devices on the downstream I2C-bus.
上傳時間： 2013-10-09
上傳用戶：3294322651
The PCA9555 is a 24-pin CMOS device that provides 16 bits of General Purpose parallelInput/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed toenhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvementsinclude higher drive capability, 5 V I/O tolerance, lower supply current, individual I/Oconfiguration, and smaller packaging. I/O expanders provide a simple solution whenadditional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.The PCA9555 consists of two 8-bit Configuration (Input or Output selection); Input, Outputand Polarity Inversion (active HIGH or active LOW OPeration) registers. The systemmaster can enable the I/Os as either inputs or outputs by writing to the I/O configurationbits. The data for each Input or Output is kept in the corresponding Input or Outputregister. The polarity of the read register can be inverted with the Polarity Inversionregister. All registers can be read by the system master. Although pin-to-pin and I2C-busaddress compatible with the PCF8575, software changes are required due to theenhancements, and are discussed in Application Note AN469.
上傳時間： 2013-11-13
上傳用戶：fredguo
