I/O 型單片機使用手冊
目錄
間接尋址寄存器 – IAR, IAR0, IAR1 .............................................35間接尋址指針 – MP, MP0, MP1 ......................................................35存儲區指針 – BP .........................................................................36累加器 – ACC...................................................................................37程序計數器低字節寄存器 – PCL....................................................37表格寄存器 – TBLP,TBHP,TBLH....................................................37看門狗定時寄存器 – WDTS............................................................38狀態寄存器 – STATUS.....................................................................38中斷控制寄存器 – INTC,INTC0,INTC1 .........................................39定時/計數寄存器...............................................................................39輸入/輸出端口和控制寄存器...........................................................40UART 寄存器 .USR,UCR1,UCR2,TXR/RXR,BRG.......................40輸入/輸出端口..........................................................................................41上拉電阻............................................................................................41PA 口的喚醒......................................................................................41輸入/輸出端口控制寄存器...............................................................41引腳共享功能....................................................................................42編程注意事項....................................................................................45定時/計數器..............................................................................................46配置定時/計數器輸入時鐘源...........................................................47定時/計數寄存器 – TMR, TMR0,TMR0L/TMR0H,TMR1L/TMR1H,TMR2.....................................................................49定時/計數控制寄存器 – TMRC,TMR0C,TMR1C,TMR2C............50定時器模式........................................................................................53事件計數器模式................................................................................53脈沖寬度測量模式............................................................................54可編程分頻器(PFD)和蜂鳴器的應用..............................................55預分頻器(Prescaler)...........................................................................56輸入/輸出接口...................................................................................56編程注意事項....................................................................................57定時/計數器應用范例.......................................................................57中斷............................................................................................................59中斷寄存器........................................................................................59中斷優先權........................................................................................62外部中斷............................................................................................63定時/計數器中斷...............................................................................64UART 中斷........................................................................................64編程注意事項....................................................................................65復位和初始化............................................................................................66復位....................................................................................................66目錄iii異步串行口——UART............................................................................74UART 特性..........................................................................................74UART 外部引腳..................................................................................74數據發送.............................................................................................75UART 狀態控制寄存器......................................................................75波特率發生器.....................................................................................79UART 設置與控制..............................................................................81UART 發送器......................................................................................83UART 接收器......................................................................................84接收錯誤處理.....................................................................................85接收中斷圖解.....................................................................................86地址檢測模式.....................................................................................86暫停模式下的UART 功能.................................................................87UART 應用范例.................................................................................87振蕩器........................................................................................................89系統時鐘配置....................................................................................89系統晶體/陶瓷振蕩器.......................................................................89系統電阻電容振蕩器........................................................................90內部系統電阻電容振蕩器................................................................90RTC 振蕩器........................................................................................91看門狗定時振蕩器............................................................................91暫停和喚醒................................................................................................92暫停.....................................................................................................92進入暫停.............................................................................................92靜態電流.............................................................................................92喚醒....................................................................................................92看門狗定時器............................................................................................94掩膜選項....................................................................................................96應用電路....................................................................................................97第二部份 程序語言.....................................................................99第二章 指令集介紹.................................................................................101指令集......................................................................................................101指令周期..........................................................................................101數據的傳送......................................................................................101算術運算..........................................................................................102邏輯和移位運算..............................................................................102分支和控制的轉換..........................................................................102位運算..............................................................................................102查表運算..........................................................................................103其它運算..........................................................................................103指令設定一覽表......................................................................................104慣例..................................................................................................104I/O 型單片機使用手冊iv第三章 指令定義.....................................................................................107第四章 匯編語言和編譯器.....................................................................121常用符號..................................................................................................121語句語法..................................................................................................122名稱..................................................................................................122操作項..............................................................................................122操作數項..........................................................................................122注解..................................................................................................122編譯偽指令..............................................................................................123條件編譯偽指令..............................................................................123文件控制偽指令..............................................................................124程序偽指令......................................................................................126數據定義偽指令..............................................................................130宏指令..............................................................................................132匯編語言指令..........................................................................................136名稱..................................................................................................136助記符..............................................................................................136操作數、運算子和表達式..............................................................136其它..........................................................................................................139前置引用..........................................................................................139局部標號..........................................................................................139匯編語言保留字..............................................................................140編譯器選項..............................................................................................141編譯列表文件格式..................................................................................141源程序列表......................................................................................141編譯總結..........................................................................................142其它..................................................................................................142第三部份 開發工具................................................................... 145第五章 單片機開發工具.........................................................................147HT-IDE 集成開發環境............................................................................147盛群單片機仿真器(HT-ICE) ..................................................................149HT-ICE 接口卡.................................................................................149OTP 燒寫器.....................................................................................149OTP 適配卡.....................................................................................149系統配置..................................................................................................150HT-ICE 接口卡設置........................................................................151安裝..........................................................................................................153系統要求..........................................................................................153硬件安裝..........................................................................................153軟件安裝..........................................................................................154目錄v第六章 快速開始.....................................................................................159步驟一：建立一個新項目..............................................................159步驟二：將源程序文件加到項目中..............................................159步驟三：編譯項目..........................................................................159步驟四：燒寫OTP 單片機.............................................................160步驟五：傳送程序與掩膜選項單至Holtek ..................................160附錄............................................................................................... 161附錄A 特性曲線圖...................................................................................163附錄B 封裝信息.......................................................................................173
標簽：
單片機
使用手冊
上傳時間：
2013-10-18
上傳用戶：blacklee
