R7732_7733_7735是Richpower公司推出的高效AC TO DC 電源PWM控制芯片,最大功率可以做到75W;如有需求請聯系我電話：021-54262182EXT 114 (Eric) QQ ：1187337351
上傳時間： 2013-11-20
上傳用戶：xz85592677
長電c2383 TO-92L
上傳時間： 2013-11-09
上傳用戶：wvbxj
高的工作電壓高達100V N雙N溝道MOSFET同步驅動 The D810DCDC is a synchronous step-down switching regulator controller that can directly step-down voltages from up to 100V, making it ideal for telecom and automotive applications. The D810DCDC uses a constant on-time valley current control architecture to deliver very low duty cycles with accurate cycle-by-cycle current limit, without requiring a sense resistor. A precise internal reference provides 0.5% DC accuracy. A high bandwidth (25MHz) error amplifi er provides very fast line and load transient response. Large 1Ω gate drivers allow the D810DCDC to drive multiple MOSFETs for higher current applications. The operating frequency is selected by an external resistor and is compensated for variations in VIN and can also be synchronized to an external clock for switching-noise sensitive applications. Integrated bias control generates gate drive power from the input supply during start-up and when an output shortcircuit occurs, with the addition of a small external SOT23 MOSFET. When in regulation, power is derived from the output for higher effi ciency.
上傳時間： 2013-10-24
上傳用戶：wd450412225
Nuvoton NuMicro ICP Programmer 用戶指南
標簽： Programmer Nuvoton NuMicro ICP
上傳時間： 2013-10-27
上傳用戶：longlong12345678
畢業設計 USB TO Gigabit LAN 網卡 隨著網絡技術飛速發展，多媒體的應用越來越多，人們對網絡的要求也越來越高，為了適應市場的需求，網卡出現了。它以其結構簡單、成本低廉、兼容性強等諸多的優越性得到了廣泛的應用。由于網絡的應用越來越廣泛，網卡的應用也越來越多、功能越來越強大。開始時由于技術方面的限制，網卡只有10Mbps的吞吐量，由于網絡技術的發展，100Mbps吞吐量的網卡開始在市場上得到廣泛的應用。而現在1000Mbps吞吐量的網卡的出現又給網絡的傳輸帶來了新的活力。 論文中主要闡述了基于以太網的USB TO Gigabit LAN網卡的設計與制作。論文首先對以太網進行了介紹，緊接著講了網卡的基本知識。隨后又對USB TO Gigabit LAN網卡的電路設計和制作進行了詳細的描述。論文還包括了USB TO Gigabit LAN網卡的調試等內容。
上傳時間： 2014-12-02
上傳用戶：wab1981
詳細介紹了TLC1549系列模數轉換器的特點及工作原理，然后根據TLC1549的工作時序和A/D轉換原理針對實際問題編寫了詳細的匯編語言程序。 Abstract: A basic principle and characteristic of TLC1549 analog-to-digital converter are introduced? detailedly in this article.Through engineering-oriented illustration,a microcomputer programmer base on basic principle and time sequence of TLC1549 is writted.
上傳時間： 2014-07-16
上傳用戶：blans
PICkit™ 2 Microcontroller Programmer USER’S GUIDE This chapter contains general information that will be useful to know before using thePICkit™ 2 Microcontroller Programmer. Items discussed in this chapter include:• Document Layout• Conventions Used in this Guide• Warranty Registration• Recommended Reading• The Microchip Web Site• Development Systems Customer Change Notification Service• Customer Support• Document Revision History
標簽： Microcontrolle PICkit 8482
上傳時間： 2013-11-05
上傳用戶：妄想演繹師
1.The C Programming Language is a powerful, flexible andpotentially portable high-level programming language. 2.The C language may be used successfully to create a programfor an 8-bit MCU, but to produce the most efficient machinecode, the programmer must carefully construct the C Languageprogram.3.The programmer must not only create an efficient high leveldesign, but also pay attention to the detailed implementation.
上傳時間： 2013-12-27
上傳用戶：huanglang
The PCA9541 is a 2-to-1 I2C-bus master selector designed for high reliability dual masterI2C-bus applications where system operation is required, even when one master fails orthe controller card is removed for maintenance. The two masters (for example, primaryand back-up) are located on separate I2C-buses that connect to the same downstreamI2C-bus slave devices. I2C-bus commands are sent by either I2C-bus master and are usedto select one master at a time. Either master at any time can gain control of the slavedevices if the other master is disabled or removed from the system. The failed master isisolated from the system and will not affect communication between the on-line masterand the slave devices on the downstream I2C-bus.
上傳時間： 2013-10-09
上傳用戶：3294322651
The MAX3243E device consists of three line drivers, five line receivers, and a dual charge-pump circuit with±15-kV ESD (HBM and IEC61000-4-2, Air-Gap Discharge) and ±8-kV ESD (IEC61000-4-2, Contact Discharge)protection on serial-port connection pins. The device meets the requirements of TIA/EIA-232-F and provides theelectrical interface between an asynchronous communication controller and the serial-port connector. Thiscombination of drivers and receivers matches that needed for the typical serial port used in an IBM PC/AT, orcompatible. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-Vsupply. In addition, the device includes an always-active noninverting output (ROUT2B), which allowsapplications using the ring indicator to transmit data while the device is powered down. The device operates atdata signaling rates up to 250 kbit/s and a maximum of 30-V/ms driver output slew rate.
標簽： MULTICHANNEL 5.5 TO RS
上傳時間： 2013-10-19
上傳用戶：ddddddd
