-
The CAT25128 is a 128−Kb Serial CMOS EEPROM device internally organized as 16Kx8 bits. This features a 64−byte page write buffer and supports the Serial Peripheral Interface (SPI) protocol. The device is enabled through a Chip Select (CS) input. In addition, the required bus signals are clock input (SCK), data input (SI) and data output (SO) lines. The HOLD input may be used to pause any serial communication with the CAT25128 device. The device featuressoftware and hardware write protection, including partial as well as full array protection.
標簽：
25128
EEPRO
CMOS
CAT
上傳時間：
2013-11-15
上傳用戶：fklinran
-
This application report discusses the design of non-invasive optical plethysmographyalso called as pulsoximeter using the MSP430FG437 Microcontroller (MCU). Thepulsoximeter consists of a Peripheral probe combined with the MCU displaying theoxygen saturation and pulse rate on a LCD glass. The same sensor is used for bothheart-rate detection and pulsoximetering in this application. The probe is placed on aPeripheral point of the body such as a finger tip, ear lobe or the nose. The probeincludes two light emitting diodes (LEDs), one in the visible red spectrum (660nm) andthe other in the infrared spectrum (940nm). The percentage of oxygen in the body isworked by measuring the intensity from each frequency of light after it transmitsthrough the body and then calculating the ratio between these two intensities.
標簽：
Pulsoximeter
Single-Chip
Des
上傳時間：
2013-10-27
上傳用戶：黑漆漆
-
Although Stellaris microcontrollers have generous internal SRAM capabilities, certain applicationsmay have data storage requirements that exceed the 8 KB limit of the Stellaris LM3S8xx seriesdevices. Since microcontrollers do not have an external parallel data-bus, serial memory optionsmust be considered. Until recently, the ubiquitous serial EEPROM/flash device was the only serialmemory solution. The major limitations of EEPROM and flash technology are slow write speed, slowerase times, and limited write/erase endurance.Recently, serial SRAM devices have become available as a solution for high-speed dataapplications. The N256S08xxHDA series of devices, from AMI Semiconductor, offer 32 K x 8 bits oflow-power data storage, a fast Serial Peripheral Interface (SPI) serial bus, and unlimited write cycles.The parts are available in 8-pin SOIC and compact TSSOP packages.
標簽：
Adding
Serial
SRAM
32
上傳時間：
2013-10-14
上傳用戶：cxl274287265
-
本文依據集成電路設計方法學，探討了一種基于標準Intel 8086 微處理器的單芯片計算機平臺的架構。研究了其與SDRAM，8255 并行接口等外圍IP 的集成，并在對AMBA協議和8086 CPU分析的基礎上，采用遵從AMBA傳輸協議的系統總線代替傳統的8086 CPU三總線結構，搭建了基于8086 IP 軟核的單芯片計算機系統，并實現了FPGA 功能演示。關鍵詞：微處理器； SoC；單芯片計算機；AMBA 協議
Design of 8086 CPU Based Computer-on-a-chip System（School of Electrical Engineering and Automation, Heifei University of Technology, Hefei, 230009,China）Abstract: According to the IC design methodology, this paper discusses the design of one kind of Computer-on-a-chip system architecture, which is based on the standard Intel8086 microprocessor,investigates how to integrate the 8086 CPU and Peripheral IP such as, SDRAM controller, 8255 PPI etc. Based on the analysis of the standard Intel8086 microprocessor and AMBA Specification,the Computer-on-a-chip system based on 8086 CPU which uses AMBA bus instead of traditional three-bus structure of 8086 CPU is constructed, and the FPGA hardware emulation is fulfilled.Key words: Microprocessor; SoC; Computer-on-a-chip; AMBA Specification
標簽：
8086
CPU
單芯片
計算機系統
上傳時間：
2013-12-27
上傳用戶：kernor
-
多功能高集成外圍器件6. 1 多功能高集成外圍器件82371PCI的英文名稱：Peripheral Component Interconnect （外圍部件互聯PCI總線）；82371是PCI總線組件。ISA是：Industry Standard Architecture（工業標準體系結構）IDE是 （Integrated Device Electronics）集成電路設備簡稱PIIX4PIIX4器件（芯片）的特點1、是一種支持Pentium和PentiumII微處理器的部件。2、82371對ISA橋來說，是一種多功能PCI總線。3、對可移動性和桌面深綠色環境均提供支持。4、電源管理邏輯。5、被集成化的IDE控制器。6、增強了性能的DMA控制器。 （7）基于兩個82C59的中斷控制器。（8）基于82C54芯片的定時器。（9）USB（Universal Serial Bus）通用串行總線。（10）SMBus系統管理總線。（11）實時時鐘（12）順應Microsoft Win95所需的功能其芯片的邏輯框圖如圖6-1所示。 PIIX4芯片邏輯框圖6.1.1 概述PIIX4芯片是一個多功能的PCI器件，圖6-2 是82371在系統中扮演的角色。（續上圖）1. PCI與EIO之間的橋（PIIX4芯片）橋是不對程的，是各類不同標準總線與PCI總線連接，82371AB橋也可理解為一種總線轉換譯碼器和控制器，橋內包含復雜的協議總線信號和緩沖器。(1).在PCI系統內，當PIIX4操作時，它總是作為系統內各種模塊的主控設備，如USB和DMA控制器、IDE總線和分布式DMA的主控設備等，而且總是以ISA主控設備的名義出現。(2). 在向ISA總線或IDE總線進行傳送操作的傳送周期期間作為從屬設備使用，并對內部寄存器譯碼。PIIX4芯片（橋）的配置(1).可以把PIIX4芯片配置成整個ISA總線，或ISA總線的子集，也可擴展成EIO總線。在使用EIO總線時，可以把未使用的信號配置成通用的輸入和輸出。(2).PIIX4可直接驅動5個ISA插槽；(3).能提供字節-交換邏輯、I/O的恢復支持、等待狀態的生成以及SYSCLK的生成。(4).提供X-BUS鍵盤控制器芯片、BIOS芯片、實時時鐘芯片、二級微程序器等的選擇。2. IDE接口（總線主控設備的權利和同步DMA方式）IDE接口為4個IDE的設備提供支持，比如IDE接口的硬盤和CD-ROM等。注意：目前硬盤接口有5類：IDE、SCSI、Fibre Channel、IEEE1394和USB等。IDE口幾乎在PC機最多，因為便宜。SCSI多用于服務器和集群機。IDE的PIO IDE速率：14MB/s；而總線主控設備IDE的速率：33MB/s在PIIX4芯片的IDE系統內，配有兩個各次獨立的IDE信號通道。3. 具有兼容性的模塊—DMA、定時器/計數器、中斷控制器等（1）在PIIX4內的兩各82C37 DMA控制器經邏輯的組合，產生7個獨立的可編程通道。通道[0：3]是通過與8個二進位的硬件連線實現的。通過以字節為單位的計數進行傳送。而通道[5：7]是通過16個二進位的連線實現的，以字為單位的計數進行傳送。（2）DMA控制器還能通過PCI總線，處理舊的DMA的兩個不同的方法提供支持。（3）計數/定時器模塊在功能上與82C54等價。（4）中斷控制器與ISA兼容，其功能是兩個82C59的功能之和。
標簽：
多功能
外圍器件
集成
上傳時間：
2013-11-19
上傳用戶：3到15
-
The Motorola MPC106 PCI bridge/memory controller provides a PowerPCªmicroprocessor common hardware reference platform (CHRPª) compliant bridgebetween the PowerPC microprocessor family and the Peripheral Component Interconnect(PCI) bus. In this document, the term Ô106Õ is used as an abbreviation for the phraseÔMPC106 PCI bridge/memory controllerÕ. This document contains pertinent physicalcharacteristics of the 106. For functional characteristics refer to theMPC106 PCI Bridge/Memory Controller UserÕs Manual.This document contains the following topics:Topic PageSection 1.1, ÒOverviewÓ 2Section 1.2, ÒFeaturesÓ 3Section 1.3, ÒGeneral ParametersÓ 5Section 1.4, ÒElectrical and Thermal CharacteristicsÓ 5Section 1.5, ÒPin AssignmentsÓ 17Section 1.6, ÒPinout Listings 18Section 1.7, ÒPackage DescriptionÓ 22Section 1.8, ÒSystem Design InformationÓ 24Section 1.9, ÒDocument Revision HistoryÓ 29Section 1.10, ÒOrdering InformationÓ 29
標簽：
MPC
106
PCI
存儲器
上傳時間：
2013-11-04
上傳用戶：as275944189
-
Internal Interrupts are used to respond to asynchronous requests from a certain part of themicrocontroller that needs to be serviced. Each Peripheral in the TriCore as well as theBus Control Unit, the Debug Unit, the Peripheral Control Processor (PCP) and the CPUitself can generate an Interrupt Request.So what is an external Interrupt?An external Interrupt is something alike as the internal Interrupt. The difference is that anexternal Interrupt request is caused by an external event. Normally this would be a pulseon Port0 or Port1, but it can be even a signal from the input buffer of the SSC, indicatingthat a service is requested.The User’s Manual does not explain this aspect in detail so this ApNote will explain themost common form of an external Interrupt request. This ApNote will show that there is aneasy way to react on a pulse on Port0 or Port1 and to create with this impulse an InterruptService Request. Later in the second part of the document, you can find hints on how todebounce impulses to enable the use of a simple switch as the input device.Note: You will find additional information on how to setup the Interrupt System in theApNote “First steps through the TriCore Interrupt System” (AP3222xx)1. It would gobeyond the scope of this document to explain this here, but you will find selfexplanatoryexamples later on.
標簽：
Exter
easy
work
with
上傳時間：
2013-10-27
上傳用戶：zhangyigenius
-
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and thePeripheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a Peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the Peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
標簽：
Signal
Input
Fall
Rise
上傳時間：
2013-10-23
上傳用戶：copu
-
The P90CL301 is a highly integrated 16/32 bit micro-controller especially suitable for applications requiring lowvoltage and low power consumption. It is fully software compatible with the 68000. Furthermore, it provides bothstandard as well as advanced Peripheral functions on-chip.One of these Peripheral functions is the I2C bus. This report describes worked-out driver software (written in C) toprogram the P90CL301 I2C interface. It also contains interface software routines offering the user a quick start inwriting a complete I2C system application.
標簽：
P90
301
IIC
90
上傳時間：
2014-01-06
上傳用戶：氣溫達上千萬的
-
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and thePeripheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a Peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the Peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.
標簽：
C16x
微控制器
輸入信號
時序圖
上傳時間：
2014-04-02
上傳用戶：han_zh
