All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
上傳時間： 2013-10-23
上傳用戶：copu
基于USB接口的數據采集模塊的設計與實現Design and Implementation of USB-Based Data Acquisition Module路 永 伸(天津科技大學電子信息與自動化學院，天津300222)摘要文中給出基于USB接口的數據采集模塊的設計與實現。硬件設計采用以Adpc831與PDIUSBDI2為主的器件進行硬件設計，采用Windriver開發USB驅動，并用Visual C十十6.0對主機軟件中硬件接口操作部分進行動態鏈接庫封裝。關鍵詞USB 數據采集Adpc831 PDNSBDI2 Windriver動態鏈接庫Abstract T hed esigna ndim plementaitono fU SB-BasedD ataA cquisiitonM oduleis g iven.Th ec hips oluitonm ainlyw ithA dpc831a ndP DTUSBD12i sused for hardware design. The USB drive is developed場Wmdriver, and the operation on the hardware interface is packaged into Dynamic Link Libraries場Visual C++6.0. Keywords USB DataA cquisition Adttc831 PDfUSBD12 Windriver0 引言US B總 線 是新一代接口總線，最初推出的目的是為了統一取代PC機的各類外設接口，迄今經歷了1.0,1.1與2.0版本3個標準。在國內基于USB總線的相關設計與開發也得到了快速的發展，很多設計者從各自的應用領域，用不同方案設計出了相應的裝置[1,2]。數據采集是工業控制中一個普遍而重要的環節，因此開發基于USB接口的數據采集模塊具有很強的現實應用意義。雖然 US B總線標準已經發展到2.0版本，但由于工業控制現場干擾信號的情況比較復雜，高速數據傳輸的可靠性不容易被保證，并且很多場合對數據采集的實時性要求并不高，開發2.0標準產品的成本又較1.1標準產品高，所以筆者認為，在工業控制領域，目前開發基于USB總線1.1標準實現的數據采集模塊的實用意義大于相應2.0標準模塊。
上傳時間： 2013-10-23
上傳用戶：q3290766
摘 要:用一種新的思路和方法,先計算低通、再計算高通濾波器的有關參數,然后組合成帶通濾波器.關鍵詞:濾波器;參數;新思路中圖分類號: TN713. 5 文獻識別碼:B 文章編號:1008 - 1666 (1999) 04 - 0089 - 03A New Consideration of the Band Filter’s CalculationGuo Wencheng( S hao Yang B usiness and Technology school , S haoyang , Hunan ,422000 )Abstract :This essay deals with a new method of calculating the band filters - first calculatingthe relevant parameters of low - pass filters ,then calculating the ones of high - pass filters.Key words :filter ; parameters ;new considercation八十年代后,信息產業得到了迅猛發展. 帶通濾波器在微波通信、廣播電視和精密儀器設備中得到了廣泛應用. 帶通濾波器性能的優劣,對提高接收機信噪比,防止鄰近信道干擾,提高設備的技術指標,有著十分重要的意義.我在長期的教學實踐中,用切比雪夫型方法設計、計算出寬帶濾波器集中參數元件的數據. 該濾波器可運用在檢測微波頻率的儀器和其他設備中. 再將其思路和計算方法介紹給大家,供參考.
上傳時間： 2014-12-28
上傳用戶：Yukiseop
load initial_track s; % y:initial data,s:data with noiseT=0.1; % yp denotes the sample value of position% yv denotes the sample value of velocity% Y=[yp(n);yv(n)];% error deviation caused by the random acceleration % known dataY=zeros(2,200);Y0=[0;1];Y(:,1)=Y0;A=[1 T 0 1]; B=[1/2*(T)^2 T]';H=[1 0]; C0=[0 0 0 1];C=[C0 zeros(2,2*199)];Q=(0.25)^2; R=(0.25)^2;
上傳時間： 2014-12-28
上傳用戶：asaqq
磁芯電感器的諧波失真分析 摘 要：簡述了改進鐵氧體軟磁材料比損耗系數和磁滯常數ηB，從而降低總諧波失真THD的歷史過程，分析了諸多因數對諧波測量的影響，提出了磁心性能的調控方向。 關鍵詞：比損耗系數， 磁滯常數ηB ，直流偏置特性DC-Bias，總諧波失真THD Analysis on THD of the fer rite co res u se d i n i nductancShi Yan Nanjing Finemag Technology Co. Ltd., Nanjing 210033 Abstract: Histrory of decreasing THD by improving the ratio loss coefficient and hysteresis constant of soft magnetic ferrite is briefly narrated. The effect of many factors which affect the harmonic wave testing is analysed. The way of improving the performance of ferrite cores is put forward. Key words: ratio loss coefficient，hysteresis constant，DC-Bias，THD 近年來，變壓器生產廠家和軟磁鐵氧體生產廠家，在電感器和變壓器產品的總諧波失真指標控制上，進行了深入的探討和廣泛的合作，逐步弄清了一些似是而非的問題。從工藝技術上采取了不少有效措施，促進了質量問題的迅速解決。本文將就此熱門話題作一些粗淺探討。 一、 歷史回顧 總諧波失真（Total harmonic distortion） ，簡稱THD，并不是什么新的概念，早在幾十年前的載波通信技術中就已有嚴格要求<1>。1978年郵電部公布的標準YD/Z17－78“載波用鐵氧體罐形磁心”中，規定了高μQ材料制作的無中心柱配對罐形磁心詳細的測試電路和方法。如圖一電路所示，利用LC組成的150KHz低通濾波器在高電平輸入的情況下測量磁心產生的非線性失真。這種相對比較的實用方法，專用于無中心柱配對罐形磁心的諧波衰耗測試。 這種磁心主要用于載波電報、電話設備的遙測振蕩器和線路放大器系統，其非線性失真有很嚴格的要求。 圖中 ZD —— QF867 型阻容式載頻振蕩器，輸出阻抗 150Ω， Ld47 —— 47KHz 低通濾波器，阻抗 150Ω，阻帶衰耗大于61dB， Lg88 ——并聯高低通濾波器，阻抗 150Ω，三次諧波衰耗大于61dB Ld88 ——并聯高低通濾波器，阻抗 150Ω，三次諧波衰耗大于61dB FD —— 30～50KHz 放大器， 阻抗 150Ω， 增益不小于 43 dB，三次諧波衰耗b3(0)≥91 dB, DP —— Qp373 選頻電平表，輸入高阻抗， L ——被測無心罐形磁心及線圈， C ——聚苯乙烯薄膜電容器CMO-100V-707APF±0.5%,二只。 測量時，所配用線圈應用絲包銅電磁線SQJ9×0.12(JB661-75)在直徑為16.1mm的線架上繞制 120 匝， （線架為一格） ， 其空心電感值為 318μH（誤差1％） 被測磁心配對安裝好后，先調節振蕩器頻率為 36.6～40KHz， 使輸出電平值為+17.4 dB， 即選頻表在 22′端子測得的主波電平 （P2）為+17.4 dB，然后在33′端子處測得輸出的三次諧波電平（P3）， 則三次諧波衰耗值為：b3(+2)= P2+S+ P3 式中：S 為放大器增益dB 從以往的資料引證， 就可以發現諧波失真的測量是一項很精細的工作，其中測量系統的高、低通濾波器，信號源和放大器本身的三次諧波衰耗控制很嚴，阻抗必須匹配，薄膜電容器的非線性也有相應要求。濾波器的電感全由不帶任何磁介質的大空心線圈繞成，以保證本身的“潔凈” ，不至于造成對磁心分選的誤判。 為了滿足多路通信整機的小型化和穩定性要求， 必須生產低損耗高穩定磁心。上世紀 70 年代初，1409 所和四機部、郵電部各廠，從工藝上改變了推板空氣窯燒結，出窯后經真空罐冷卻的落后方式，改用真空爐，并控制燒結、冷卻氣氛。技術上采用共沉淀法攻關試制出了μQ乘積 60 萬和 100 萬的低損耗高穩定材料，在此基礎上，還實現了高μ7000～10000材料的突破，從而大大縮短了與國外企業的技術差異。當時正處于通信技術由FDM（頻率劃分調制）向PCM（脈沖編碼調制） 轉換時期， 日本人明石雅夫發表了μQ乘積125 萬為 0.8×10 ，100KHz）的超優鐵氧體材料<3>，其磁滯系數降為優鐵
上傳時間： 2013-12-15
上傳用戶：天空說我在
最新的支持向量機工具箱，有了它會很方便 1. Find time to write a proper list of things to do! 2. Documentation. 3. Support Vector Regression. 4. Automated model selection. REFERENCES ========== [1] V.N. Vapnik, "The Nature of Statistical Learning Theory", Springer-Verlag, New York, ISBN 0-387-94559-8, 1995. [2] J. C. Platt, "Fast training of support vector machines using sequential minimal optimization", in Advances in Kernel Methods - Support Vector Learning, (Eds) B. Scholkopf, C. Burges, and A. J. Smola, MIT Press, Cambridge, Massachusetts, chapter 12, pp 185-208, 1999. [3] T. Joachims, "Estimating the Generalization Performance of a SVM Efficiently", LS-8 Report 25, Universitat Dortmund, Fachbereich Informatik, 1999.
上傳時間： 2013-12-16
上傳用戶：亞亞娟娟123
Blaster is a simple application that illustrates Windows NT 5.0’s support of the IrDA protocol. IrDA provides reliable point to point connectivity between 2 computers equipped with infrared
標簽： IrDA application illustrates protocol
上傳時間： 2015-03-29
上傳用戶：Thuan
This simple simulation of a pulse traveling down a parallel-plate guide makes a handy test code for initial experiments with boundary conditions. ToyFDTD3 adds some simple features to ToyFDTD1: A PMC boundary condition, a sinusoidal pulse source, and output tracking a single point in the mesh. Released 15 June 1999.
標簽： parallel-plate simulation traveling simple
上傳時間： 2015-04-06
上傳用戶：stella2015
Description: FASBIR(Filtered Attribute Subspace based Bagging with Injected Randomness) is a variant of Bagging algorithm, whose purpose is to improve accuracy of local learners, such as kNN, through multi-model perturbing ensemble. Reference: Z.-H. Zhou and Y. Yu. Ensembling local learners through multimodal perturbation. IEEE Transactions on Systems, Man, and Cybernetics - Part B: Cybernetics, 2005, vol.35, no.4, pp.725-735.
標簽： Description Randomness Attribute Filtered
上傳時間： 2015-04-10
上傳用戶：ynzfm
RFC1661 PPP協議 （RFC1661 The Point-to-Point Protocol (PPP)） 本備忘錄狀態 This memo provides information for the Internet community. It does not specify an Internet standard of any kind. Distribution of this memo is unlimited.
標簽： 1661 Point-to-Point informatio RFC
上傳時間： 2014-12-07
上傳用戶：569342831
