隨著電磁閥在工業和日常應用的增多,其功耗越來越被人們所重視。通過對電磁閥驅動電路的研究,設計一套電磁閥節能驅動電路。不僅提高了電磁閥的響應時間,更重要的是降低了功耗,使電磁閥由工作在大電流狀態下,變成大電流啟動小電流維持的工作狀態。減少了由電流過大引起的電磁閥線圈過熱,增加了電磁閥的安全性。The power consumption of an electromagnetic valve is drawing increasingly more attentiori as it is widely used in industrial production and daily life. In this study, an energy - saving driving circuit of electromagnetic valves was designed. It can make an electromagnetic valve to start with a high current while work with a low current; thereby the power consumption can be reduced. Besides, it can shorten the response time of an electromagnetic valve and improve the security of the valve.
上傳時間： 2022-04-16
上傳用戶：
為了提高超高頻RFID系統中閱讀器在低信噪比的情況下仍具有較高的識別能力,提出一種基于FPGA系統結合軟件無線電方法實現超高頻RFID射頻前端電路方案。超高頻射頻識別系統必須符合EPC Class 1generation 2標準,所設計的電路系統以Xilinx公司的XC6SLX16-2CSG324FPGA芯片為硬件基礎,將數字基帶調制解調和中頻濾波電路在FPGA系統中設計實現,重點闡述了射頻前端電路的設計結構、AD/DA轉換電路,以及數字濾波器的設計。實驗結果表明,所設計的超高頻RFID閱讀器簡化了前端電路系統結構,提升了穩定性,增強了抗干擾能力。該電路系統在信噪比較低的情況下,能夠較好地實現915MHz頻率的射頻接收和發送。In order to improve the reader UHF RFID system still has a higher ability to identify,in the case of low signal-to-noise ratio.The UHF RFID systems must comply with EPC Class 1 generation 2 standard.In this paper,the design of the circuit system based on Xilinx＇s XC6SLX16-2CSG324 FPGA chip,and presents UHF RFID RF front-end circuit with software radio based on FPGA system.Digital baseband modem and IF filter circuit is designed and implemented in the FPGA system,and focused on designing the structure of the RF front-end circuit,AD/DA conversion circuits,and digital filter.Experimental results show that the UHF RFID reader de...
標簽： 915mhz 超高頻 rfid 閱讀 射頻 前端 電路 設計
上傳時間： 2022-04-17
上傳用戶：shjgzh
隨著科技的發展，人們在日常生活中使用的電器越來越多，電子設備的電磁兼容性（EMC）也越來越重要。所以，人們對電子設備的電磁兼容性的要求也越來越嚴格，越來越規范。而在市場競爭中，如何降低成本、減少設備體積，是各電子設備制造廠家重點研究的課題。通過對開關電源的EMI濾波電路的類別和相應的技術特點進行分析，設計出一種既能提高性能，又能降低成本的濾波電路。With the development of technology, appliances people use in their daily lives, more and more electronic devices electromagnetic compatibility （ EMC ） has become increasingly important. So, people electromagnetic compatibility requirements of electronic devices have become increasingly stringent, more and more standardized. The competition in the market, how to reduce costs, reduce equipment size, is the subject of the electronic equipment manufacturer focused on research. Through the technical characteristics of the respective category and the EMI filter circuit switching power supply is analyzed both designed to improve a performance of the filter circuit can reduce the cost.
上傳時間： 2022-04-23
上傳用戶：
超聲波換能器作為一種實用的檢測手段，能實現聲波所攜帶的信息和電能之間轉換。它的性能優良，價格低廉，操作方便，易于調試，因此在工農業生產中發揮著重要的作用。但目前換能器驅動電路的發射頻率多為40 kHz，本文針對1 MHz的超聲波換能器電路進行了設計，主要介紹了它的發射驅動電路和接收驅動電路的設計方案，并對它們的功能進行了詳細地說明。最后搭建實驗平臺，并對電路的輸入、輸出模塊進行了測試。實驗結果表明，換能器電路運行良好，可以為超聲波高精度測量領域的應用提供參考。As a practical means of detection, ultrasonic transducer can realize the conversion between theinformation carried by sound wave and electric energy.It has the advantages of excellent performance,low cost, convenient operation and debugging, so plays an important role in industrial and agriculturalproduction.However, the transmitting frequency of the driving circuit for most transducer is 40 kHz.Thecircuit of 1 MHz ultrasonic transducer is designed In this paper. It mainly introduces the emissive drivingcircuit and the receiving circuit design and the detailed function of them. Finally, the experimentalplatform is built, and the circuit of input and output were tested. Experiments show that the transducer＇ s...
上傳時間： 2022-04-28
上傳用戶：
針對交流電路過零檢測電路存在結構復雜、過零點檢測不準確、編程繁瑣等問題，設計了一種基于LM339的硬件結構簡單的過零檢測電路。通過仿真軟件Mulisim對該設計電路進行了仿真，實驗證明了該方案過零檢測的可行性、穩定性和可靠性，可直接作為交流電路中CPU的過零信號。Aiming at the problems of AC cilsuit zero crossing detection circuit such as complex structure, zero crossing detection and cumbersome programming, a zero crossing detection circuit with simple hardware structure based on LM339 was designed. The design circuit was simulated by simulation software Mulisim, and the feasibility, stability and reliability of zero crossing detection were proved by experiments, which can be used as zero crossing signal of CPU in AC circuit directly.
上傳時間： 2022-05-03
上傳用戶：
為解決移相全橋電路驅動及相角控制問題,設計了一種數字控制的移相全橋驅動電路.以TPL521為光耦隔離、IR2110為柵極驅動芯片.由DSP產生PWM信號,經過光耦隔離和邏輯電路后送至IR2110進行相角控制.文章對IR2110驅動電路原理進行分析及參數進行設計,對TMS320F28335進行設置并給出部分代碼.實驗結果表明：通過TMS320F28335可產生的不同相角的PWM波形,滿足了移相全橋對不同相角控制的要求.In order to solve the problem of phase-shifted full-bridge circuit driving and phase angle control,a digitally controlled phaseshifted full-bridge driving circuit was designed. TPL521 optocoupler isolation,IR2110 gate driver chip. PWM signals are generated by the DSP and sent to the IR2110 for phase angle control after optocoupler isolation and logic circuits. This text carries on the analysis to the principle of IR2110 drive circuit and parameter design,set up and give out some code to TMS320F28335. The experimental results show that the PWM waveforms with different phase angles generated by TMS320F28335 can meet the requirements of phase-shifted full-bridge control for different phase angles.
上傳時間： 2022-05-03
上傳用戶：zhanglei193
基于TMS320F28335的超聲波流量計硬件原理圖+軟件源碼本文以TMS320F28335 處理器為核心，設計一種用于管道流量測量的超聲波流量計。系統硬件由核心板，超聲波發射和接收電路，切換電路，超聲換能器，基于ADS805 的高速信號采集電路，人機交互以及電源等模塊構成。采用時差法進行管道流量測量，時差測量采用SCOT 加權的廣義互相關時延估計算法。本論文設計的超聲波流量計具有測量速度快、準確性好、成本低等優點。關鍵字：C2000，超聲波，流量，廣義互相關算法AbstractA kind of ultrasonic flowmeter using for the pipe flow measurement is designed based onTMS320F28335 in this paper. The system hardware consists of the following parts: the core board,ultrasonic signal transmitter and receiver circuits, switch circuit, ultrasonic transducer, signalacquisition circuit based on ADS805, human-computer interaction module and power supplymodule, etc. The system use the method of time difference for pipeline flow measurement and thetime difference is calculated by the time-delay algorithm of SCOT weighted generalizedcross-correlation. The ultrasonic flowmeter has the features of high testing speed, high precisionand low cost, etc.Keywords: C2000,Ultrasonic, Flow, Generalized Cross-Correlation Algorithm
標簽： tms320f28335 超聲波流量計
上傳時間： 2022-05-06
上傳用戶：
以STM32F103C8T6為核心,設計了無刷直流電機控制器硬件電路。電路主要包括IR2310構成的PWM驅動電路、IRF3808構成的逆變電路、增量式旋轉編碼構成的速度反饋電路。控制器具有CAN和RS232通信接口,可與計算機或PLC構成速度或位置伺服系統。利用由xPC目標搭建的半實物仿真平臺對PI參數進行整定。測試了控制器的速度伺服響應性能,給定速度為2400rpm時,控制器響應時間為0.32s。實驗結果表明,系統工作可靠,穩定性好,響應速度快,可以滿足上肢康復機器人的機械臂速度控制性能要求。The hardware circuit of Brushless DC motor controller is designed by taking STM32F103C8T6 as the core,which mainly includes PWM driving circuits made up of IR2310,inverter circuit formed by IRF3808,speed feedback circuit composed of incremental rotary encoder and so on.Speed servo control system or position servo control system can be composed of BLDM controller with computer or PLC through CAN communication interface or RS232 serial communication interface.By using the hardware in the loop simulation platform built by xPC target,the PI parameters are set up.The Speed servo response performance of the controller is tested.When the speed is 2 400 rpm,the response time of the controller is 0...
上傳時間： 2022-05-07
上傳用戶：
基于DSP28335的永磁同步電機調速系統設計摘要（中英文） 本控制系統的設計是為了實現基于TMS320F28335的永磁同步電動機的調速系統，并把它引用到全電動注塑機當中。本系統使用SVPWM的控制方法，通過采樣電機電流和旋轉變壓器的位置信息，實現速度、電流雙閉環控制。通過TMS320F28335的硬件浮點處理核心，實現應用于永磁同步電機的浮點算法，去取代過去的定點算法，提高代碼效率。 Abstract: The control system is designed to realize TMS320F28335 based on the permanent magnet synchronous motor speed control system, and put it to quoting all electric of injection molding machine. The ystem of the control method used SVPWM, through the sampling motor current and rotating transformer 1. 引言1.1 設計背景及目的 本永磁同步電機調速系統是全電動注塑機的其中一個應用部分。全電動注塑機憑借著其節約能源、清潔、噪聲少、速度控制效果好、精度高、可重復性高、成本低等眾多優點，成為了當下高端注塑機發展的一個方向。 全電動注塑機的所有運動機構都采用交流伺服電動機驅動，一個穩定高效的永磁同步電動機驅動方案成為了全電動注塑機性能的一個總要部分。本次設計以適用于全電動注塑機的永磁同步電動機控制系統為目標進行設計，采用TI公司的TMS320F28335作為控制核心。憑借TMS320F28335高速的運算能力，適用于電動機控制的各種外設，以及TMS320F283XX特有的硬件浮點運算能力，進行永磁同步電動機的調速控制系統的設計。
上傳時間： 2022-05-08
上傳用戶：
數字頻率計是電工電子中常用的測量儀器,數字頻率計通過用輸入待測信號對一特定長度的信號進行計數,從而得出頻率并通過數碼管直觀的顯示出來。本文提出了一種與輸入同步的數字頻率計的設計,提高了頻率計的精度,設計采用Multisim軟件進行設計和仿真的過程,介紹了其工作原理,硬件電路設計和仿真的過程。設計采用了Multisim軟件進行設計和仿真,設計結果得到的驗證。Digital frequency counter is used to measure the frequency of a signal.It is common to use a multivibrator to generate a standard 1 second time base signal and count input signal gated by this signal.However,the asynchronous of this time base signal with input signal will bring errors.In this paper,a high precision frequency counter which use synchronized time base signal generator is proposed.This frequency counter is designed and simulated by Multisim tools and result is verified.
標簽： multisim
上傳時間： 2022-05-08
上傳用戶：
