通過比較各種隔離數字通信的特點和應用范圍，指出塑料光纖在隔離數字通信中的優勢。使用已經標準化的TOSLINK接口，有利于節省硬件開發成本和簡化設計難度。給出了塑料光纖的硬件驅動電路，說明設計過程中的注意事項，對光收發模塊的電壓特性和頻率特性進行全面試驗，并給出SPI口使用塑料光纖隔離通信的典型應用電路圖。試驗結果表明，該設計可為電力現場、電力電子及儀器儀表的設計提供參考。 Abstract: y comparing characteristics and applications area of various isolated digital communications， this article indicates advantages of plastic optical fiber in isolated digital communications. Using the standardized TOSLINK interface， it helps to control costs and difficulty in hardware development and design. Then it gives the hardware driver circuit of plastic optical fiber module， explains the noticed details in design process， gives results on the basis of the optical transceiver module voltage characteristics and frequency characteristics tests. Finally，it gives typical application circuit of the SPI communication port by using plastic optical fiber isolation .The results show that this design can be referenced for the power field， power electronics and instrumentation design.
上傳時間： 2014-01-10
上傳用戶：gundan
Single-Ended and Differential S-Parameters Differential circuits have been important incommunication systems for many years. In the past,differential communication circuits operated at lowfrequencies, where they could be designed andanalyzed using lumped-element models andtechniques. With the frequency of operationincreasing beyond 1GHz, and above 1Gbps fordigital communications, this lumped-elementapproach is no longer valid, because the physicalsize of the circuit approaches the size of awavelength.Distributed models and analysis techniques are nowused instead of lumped-element techniques.Scattering parameters, or S-parameters, have beendeveloped for this purpose [1]. These S-parametersare defined for single-ended networks. S-parameterscan be used to describe differential networks, but astrict definition was not developed until Bockelmanand others addressed this issue [2]. Bockelman’swork also included a study on how to adapt single-ended S-parameters for use with differential circuits[2]. This adaptation, called “mixed-mode S-parameters,” addresses differential and common-mode operation, as well as the conversion betweenthe two modes of operation.This application note will explain the use of single-ended and mixed-mode S-parameters, and the basicconcepts of microwave measurement calibration.
上傳時間： 2014-03-25
上傳用戶：yyyyyyyyyy
提出了一種以ARM微處理器為控制核心的遠程無線視頻監控終端的設計方案，其監控終端的硬件設計包括視頻采集處理、中央管理控制、無線傳輸3個模塊。并給出了監控終端的軟件開發平臺和開發模式的系統啟動代碼、嵌入式Linux系統移植以及驅動程序和應用程序。測試結果表明，該監控終端設計方案合理、有效，基本滿足監控需求。 Abstract: A remote wireless video monitoring terminal design， which uses ARM microprocessor as its core control， is proposed in this paper.The hardware design of monitoring terminal system is composed of the video acquisition and processing module， the central management and control module， wireless transmission module.Meanwhile the monitoring terminal-s software development platform and development patterns are designed. Also the design of the system-s start codes， embedded Linux system-s transplantation process， driver and the corresponding applications are given. The results showed that the monitoring terminal design is reasonable， effective， basically meet monitoring requirements.
上傳時間： 2013-11-13
上傳用戶：wanqunsheng
The LPC1850/30/20/10 are ARM Cortex-M3 based microcontrollers for embeddedapplications. The ARM Cortex-M3 is a next generation core that offers systemenhancements such as low power consumption, enhanced debug features, and a highlevel of support block integration.The LPC1850/30/20/10 operate at CPU frequencies of up to 150 MHz. The ARMCortex-M3 CPU incorporates a 3-stage pipeline and uses a Harvard architecture withseparate local instruction and data buses as well as a third bus for peripherals. The ARMCortex-M3 CPU also includes an internal prefetch unit that supports speculativebranching.The LPC1850/30/20/10 include up to 200 kB of on-chip SRAM data memory, a quad SPIFlash Interface (SPIFI), a State Configuration Timer (SCT) subsystem, two High-speedUSB controllers, Ethernet, LCD, an external memory controller, and multiple digital andanalog peripherals.
上傳時間： 2014-12-31
上傳用戶：zhuoying119
The NXP LPC315x combine an 180 MHz ARM926EJ-S CPU core, High-speed USB 2.0OTG, 192 KB SRAM, NAND flash controller, flexible external bus interface, an integratedaudio codec, Li-ion charger, Real-Time Clock (RTC), and a myriad of serial and parallelinterfaces in a single chip targeted at consumer, industrial, medical, and communicationmarkets. To optimize system power consumption, the LPC315x have multiple powerdomains and a very flexible Clock Generation Unit (CGU) that provides dynamic clockgating and scaling.The LPC315x is implemented as multi-chip module with two side-by-side dies, one fordigital fuctions and one for analog functions, which include a Power Supply Unit (PSU),audio codec, RTC, and Li-ion battery charger.
上傳時間： 2014-01-17
上傳用戶：Altman
ORCAD在使用的時候總會出現這樣或那樣的問題…但下這個問題比較奇怪…在ORCAD中無法輸出網表…彈出下面的錯誤….這種問題很是奇怪…Netlist Format: tango.dllDesign Name: D:\EDA_PROJECT\PROTEL99SE\YK\SV3200\MAIN.DSNERROR [NET0021] Cannot get part.[FMT0024] Ref-des not found. Possible Logical/Physical annotation conflict.[FMT0018] Errors processing intermediate file找了一天沒找到問題…終于在花了N多時間后發現問題所在…其實這個問題就是不要使用ORCAD PSPICE 庫里面的元件來畫電路圖…實際中我是用了PSPICE里面和自己制作的二種電阻和電容混合在一起…就會出現這種問題…
上傳時間： 2013-11-21
上傳用戶：zaocan888
SDH[1](Synchronous Digital Hierarchy，同步數字體系)光端機容量較大，一般是16E1到4032E1。SDH是一種將復接、線路傳輸及交換功能融為一體、并由統一網管系統操作的綜合信息傳送網絡，是美國貝爾通信技術研究所提出來的同步光網絡(SONET)。
上傳時間： 2013-11-07
上傳用戶：3到15
This book is about the digital logic design of microprocessors. It is intended to provide both an understanding of the basic principles of digital logic design, and how these fundamental principles are applied in the building of complex microprocessor circuits using current technologies.
上傳時間： 2013-10-14
上傳用戶：leyesome
摘要：介紹了基于數字信號處理(Digital Signal Processor,DSP)的運動控制器GT-800在貼片機控制系統中的應用。該系統采用以PC機為上位機、GT-800運動控制器為下位機的硬件結構，上下位機之間的通訊采用基于ISA總線的雙端口RAM的模式，系統的軟件設計采用基于VisualC++6．0的軟件設計模式。關鍵詞：GT-800運動控制器；貼片機；運動控制；機器視覺
上傳時間： 2013-10-18
上傳用戶：asdkin
LSB數字水印技術 數字水印（Digital Watermarking）技術是將一些標識信息(即數字水印)直接嵌入數字載體當中(包括多媒體、文檔、軟件等)或是間接表示(修改特定區域的結構)，且不影響原載體的使用價值，也不容易被探知和再次修改。但可以被生產方識別和辨認。通過這些隱藏在載體中的信息，可以達到確認內容創建者、購買者、傳送隱秘信息或者判斷載體是否被篡改等目的。數字水印是信息隱藏技術的一個重要研究方向。 數字水印是實現版權保護的有效辦法，是信息隱藏技術研究領域的重要分支。作為一種新型的有效的版權保護手段，數字水印技術倍受人們的關注。數字水印主要是通過在原始資料中嵌入秘密信息——水印,來證實資料的所有權。
上傳時間： 2013-10-15
上傳用戶：清風冷雨
