booth乘法器： 16*16有符號乘法器，Booth編碼，簡單陣列，Ripple Carry Adder
上傳時間： 2014-01-16
上傳用戶：努力努力再努力
16*16有符號乘法器的 編碼方式：Booth編碼， 拓撲結構：簡單陣列 加法器：Ripple Carry Adder
上傳時間： 2014-01-13
上傳用戶：com1com2
The AP2406 is a 1.5Mhz constant frequency, slope compensated current mode PWM step-down converter. The device integrates a main switch and a synchronous rectifier for high efficiency without an external Schottky diode. It is ideal for powering portable equipment that runs from a single cell lithium-Ion (Li+) battery. The AP2406 can supply 600mA of load current from a 2.5V to 5.5V input voltage. The output voltage can be regulated as low as 0.6V. The AP2406 can also run at 100% duty cycle for low dropout operation, extending battery life in portable system. Idle mode operation at light loads provides very low output Ripple voltage for noise sensitive applications. The AP2406 is offered in a low profile (1mm) 5-pin, thin SOT package, and is available in an adjustable version and fixed output voltage of 1.2V, 1.5V and 1.8V
上傳時間： 2017-02-23
上傳用戶：w124141
The PW2163 is a high efficiency 500 kHz synchronous step-down DC-DC converter capable ofdelivering 3A current. The PW2163 operates over a wide input voltage range from 4.5V to 18V andintegrates main switch and synchronous switch with very low RDS(ON) to minimize the conductionloss. Low output voltage Ripple and small external inductor and capacitor sizes are achieved with 500kHz switching frequency. It adopts the instant PWM architecture to achieve fast transient responsesfor high step down applications
標簽： pw2163
上傳時間： 2022-02-11
上傳用戶：
The PW2053 is a high-efficiency monolithic synchronous buck regulator using a constantfrequency, current mode architecture. The device is available in an adjustable version. Supply currentwith no load is 40uA and drops to <1uA in shutdown. The 2.5V to 5.5V input voltage range makesthe PW2053 ideally suited for single Li-Ion battery powered applications. 100% duty cycle provideslow dropout operation, extending battery life in portable systems. PWM/PFM mode operationprovides very low output Ripple voltage for noise sensitive applications. Switching frequency isinternally set at 1.2MHz, allowing the use of small surface mount inductors and capacitors. Lowoutput voltages are easily supported with the 0.6V feedback reference voltage
標簽： pw2053
上傳時間： 2022-02-14
上傳用戶：jason_vip1
為設計高效率、低損耗的PFC電路,本文基于UCC28019進行電路設計。以UCC28019輸出的PWM波形來控制Boost升壓斬波為核心電路,使電路中的電容交替地充放電、電感交替的儲存和釋放能量,最后實現在輸入AC20V~24V電壓情況下穩定輸出DC38V。測試結果表明,系統實現效率為95%左右,電壓調整率小于1%,電源功率因數0.99。交流輸入電壓為19.0-25.8 V時,輸出直流電壓穩定性較好,電感無明顯嘯叫且紋波小,具有一定的帶負載能力和實用性。In order to design the PFC circuit with high efficiency and low loss,this paper designs the circuit based on UCC28019.The PWM waveform output by UCC28019 is used to control boost chopper as the core circuit,which alternately charges and discharges capacitors,stores and releases energy by inductors,and finally achieves stable output of DC38 V under the input voltage of AC20 V~24 V.The test results show that the system achieves about 95% efficiency,the voltage adjustment rate is less than 1%,the power factor is 0.99,and the AC input voltage is 19.0-25.8 V.The output DC voltage stability is good,the inductance has no obvious whistle and the Ripple is small,so it has certain load capacity and practicability.
上傳時間： 2022-04-03
上傳用戶：
