AEC-Q100 qualified
? 12 V and 24 V battery systems compliance
? 3.3 V and 5 V logic compatible I/O
? 8-channel configurable MOSFET pre-driver
– High-SIDE (N-channel and P-channel MOS)
– Low-SIDE (N-channel MOS)
– H-bridge (up to 2 H-bridge)
– Peak & Hold (2 loads)
? Operating battery supply voltage 3.8 V to 36 V
? Operating VDD supply voltage 4.5 V to 5.5 V
? All device pins, except the ground pins, withstand at least 40 V
? Programmable gate charge/discharge currents for improving EMI behavior
Description
The L9352B is an integrated quad low-SIDE power
switch to drive inductive loads like valves used in
ABS systems. Two of the four channels are
current regulators with current range from 0 mA to
2.25 A.
All channels are protected against fail functions.
They are monitored by a status output.
This book provides the essential design techniques for radio systems that
operate at frequencies of 3 MHz to 100 GHz and which will be employed in
the telecommunication service. We may also call these wireless systems,
wireless being synonymous with radio, Telecommunications is a vibrant indus-
try, particularly on the ‘‘radio SIDE of the house.’’ The major supporter of this
upsurge in radio has been the IEEE and its 802 committees. We now devote
? . an entire chapter to wireless LANs WLANs detailed in IEEE 802.11. We
also now have subsections on IEEE 802.15, 802.16, 802.20 and the wireless
? . ? metropolitan area network WMAN . WiFi, WiMax,, and UWB ultra wide-
. band are described where these comparatively new radio specialties are
demonstrating spectacular growth.
Software Radio (SR) is one of the most important emerging technologies for the
future of wireless communication services. By moving radio functionality into
software, it promises to give flexible radio systems that are multi-service, multi-
standard, multi-band, reconfigurable and reprogrammable by software.
Today’s radios are matched to a particular class of signals that are well defined
bytheircarrierfrequencies,modulationformatsandbandwidths.Aradiotransmitter
today can only up convert signals with well-defined bandwidths over defined center
frequencies, while, on the other SIDE of the communication chain, a radio receiver
can only down convert well-defined signal bandwidths, transmitted over specified
carrier frequencies.
Wireless communications has become a field of enormous scientific and economic interest. Recent
success stories include 2G and 3G cellular voice and data services (e.g., GSM and UMTS), wireless
local area networks (WiFi/IEEE 802.11x), wireless broadband access (WiMAX/IEEE 802.16x), and
digital broadcast systems (DVB, DAB, DRM). On the physical layer SIDE, traditional designs typically
assume that the radio channel remains constant for the duration of a data block. However, researchers
and system designers are increasingly shifting their attention to channels that may vary within a block.
In addition to time dispersion caused by multipath propagation, these rapidly time-varying channels
feature frequency dispersion resulting from the Doppler effect. They are, thus, often referred to as
being “doubly dispersive.”
An acronym for Multiple-In, Multiple-Out, MIMO communication sends the same data as several signals
simultaneously through multiple antennas, while still utilizing a single radio channel. This is a form of
antenna diversity, which uses multiple antennas to improve signal quality and strength of an RF link. The
data is split into multiple data streams at the transmission point and recombined on the receive SIDE by
another MIMO radio configured with the same number of antennas. The receiver is designed to take
into account the slight time difference between receptions of each signal, any additional noise or
interference, and even lost signals.
Nowadays sensors are part of everyday life in a wide variety of fields: scientific
applications, medical instrumentation, industrial field, ...and, last but not least,
popular mass production and low-cost goods, like smartphones and other mobile
devices. Markets and business behind the field of sensors are quite impressive.
A common trend for consumer applications is miniaturization which requires, on
one SIDE, a lot of research, development efforts, and resources but, on the other
hand, allows costs and final application size reduction. In this scenario scientific
community and industries are very active to drive innovation.
ABSTRACTThe flyback power stage is a popular choice for single and multiple output dc-to-dc converters at powerlevels of 150 Watts or less. Without the output inductor required in buck derived topologies, such as theforward or push-pull converter, the component count and cost are reduced. This application note will reviewthe design procedure for the power stage and control electronics of a flyback converter. In these isolatedconverters, the error signal from the secondary still needs to cross the isolation boundary to achieveregulation. By using the UC3965 Precision Reference with Low Offset Error Amplifier on the secondarySIDE to drive an optocoupler and the UCC3809 Economy Primary SIDE Controller on the primary SIDE, asimple and low cost 50 Watt isolated power supply is realized.
STM32F驅動L6470 ■ Operating voltage: 8 - 45 V■ 7.0 A out peak current (3.0 A r.m.s.)■ Low RDS(on) Power MOSFETs■ Programmable speed profile and positioning■ Programmable power MOS slew rate■ Up to 1/128 microstepping■ Sensorless stall detection■ SPI interface■ Low quiescent and standby currents■ Programmable non-dissipative overcurrentprotection on high and low-SIDE■ Two levels of overtemperature protection
