OPTOELECTRONICS CIRCUIT COLLECTION AVALANCHE PHOTODIODE BIAS SUPPLY 1Provides an output voltage of 0V to +80V for reverse biasingan avalanche photodiode to control its gain. This circuit canalso be reconfigured to supply a 0V to –80V output.LINEAR TEC DRIVER–1This is a bridge-tied load (BTL) linear amplifier for drivinga thermoelectric cooler (TEC). It operates on a single +5Vsupply and can drive ±2A into a common TEC.LINEAR TEC DRIVER–2This is very similar to DRIVER–1 but its power output stagewas modified to operate from a single +3.3V supply in orderto increase its efficiency. Driving this amplifier from astandard +2.5V referenced signal causes the output transistorsto have unequal power dissipation.LINEAR TEC DRIVER–3This BTL TEC driver power output stage achieves very highefficiency by swinging very close to its supply rails, ±2.5V.This driver can also drive ±2A into a common TEC. Operationis shown with the power output stage operating on±1.5V supplies. Under these conditions, this linear amplifiercan achieve very high efficiency. Application ReportThe following collection of analog circuits may be useful in electro-optics applications such as optical networkingsystems. This page summarizes their salient characteristics.
上傳時間： 2013-10-27
上傳用戶：落花無痕
模擬集成電路的設計與其說是一門技術，還不如說是一門藝術。它比數字集成電路設計需要更嚴格的分析和更豐富的直覺。嚴謹堅實的理論無疑是嚴格分析能力的基石，而設計者的實踐經驗無疑是誕生豐富直覺的源泉。這也正足初學者對學習模擬集成電路設計感到困惑并難以駕馭的根本原因。.美國加州大學洛杉機分校(UCLA)Razavi教授憑借著他在美國多所著名大學執教多年的豐富教學經驗和在世界知名頂級公司(AT&T，Bell Lab，HP)卓著的研究經歷為我們提供了這本優秀的教材。本書自2000午出版以來得到了國內外讀者的好評和青睞，被許多國際知名大學選為教科書。同時，由于原著者在世界知名頂級公司的豐富研究經歷，使本書也非常適合作為CMOS模擬集成電路設計或相關領域的研究人員和工程技術人員的參考書。... 本書介紹模擬CMOS集成電路的分析與設計。從直觀和嚴密的角度闡述了各種模擬電路的基本原理和概念，同時還闡述了在SOC中模擬電路設計遇到的新問題及電路技術的新發展。本書由淺入深，理論與實際結合，提供了大量現代工業中的設計實例。全書共18章。前10章介紹各種基本模塊和運放及其頻率響應和噪聲。第11章至第13章介紹帶隙基準、開關電容電路以及電路的非線性和失配的影響，第14、15章介紹振蕩器和鎖相環。第16章至18章介紹MOS器件的高階效應及其模型、CMOS制造工藝和混合信號電路的版圖與封裝。 1 Introduction to Analog Design 2 Basic MOS Device Physics 3 Single-Stage Amplifiers 4 Differential Amplifiers 5 Passive and Active Current Mirrors 6 Frequency Response of Amplifiers 7 Noise 8 Feedback 9 Operational Amplifiers 10 Stability and Frequency Compensation 11 Bandgap References 12 Introduction to Switched-Capacitor Circuits 13 Nonlinearity and Mismatch 14 Oscillators 15 Phase-Locked Loops 16 Short-Channel Effects and Device Models 17 CMOS Processing Technology 18 Layout and Packaging
上傳時間： 2014-12-23
上傳用戶：杜瑩12345
Abstract: Rail splitting is creating an artificial virtual ground as a reference voltage. It is used to set the signalto match the op amp's "sweet spot." An op amp has the most linear- and distortion-free qualities at that sweetspot. Typically, the sweet spot occurs near the center between the single power rail and ground. In the case ofa number of signals, the virtual ground can control channel DC errors when multiplexing or switching thesignals.
上傳時間： 2013-10-23
上傳用戶：wushengwu
The CN3052A is a complete constant-current /constant voltage linear charger for single cell Li-ion and Li Polymer rechargeable batteries. The device contains an on-chip power MOSFET and eliminates the need for the external sense resistor and blocking diode.
上傳時間： 2013-11-10
上傳用戶：子虛烏有
In this paper, two types of MMIC voltage controlled oscillators have been successfully demonstrated. The first chip with single tuning diode shows the excellent tuning linearity. The second chip with two tuning diodes can improve the tuning bandwidth.
上傳時間： 2013-10-17
上傳用戶：xjz632
A number of conventional solutions have been available forthe design of a DC/DC converter where the output voltageis within the input voltage range—a common scenarioin Li-Ion battery-powered applications—but none werevery attractive until now. Conventional topologies, suchas SEPIC or boost followed by buck, have numerousdisadvantages, including low effi ciency, complex magnetics,polarity inversion and/or circuit complexity/cost. TheLTC®3785 buck-boost controller yields a simple, effi cient,low parts-count, single-converter solution that is easyto implement, thus avoiding the drawbacks associatedwith traditional solutions.
上傳時間： 2013-10-21
上傳用戶：ljt101007
The LTC®3562 quad output step-down regulator is designedfor multicore handheld microprocessor applications thatoperate from a single Li-Ion battery. Its four monolithic, higheffi ciency buck regulators support Intel’s mobile CPU P-Stateand C-State energy saving operating modes. The outputvoltages are independently controllable via I2C, and eachoutput can be independently started and shut down. Designerscan choose from power saving pulse-skipping mode orBurst Mode® operation, or select low noise LDO mode. Thespace-saving LTC3562 is available in a 3mm × 3mm QFNpackage and requires few external components.
上傳時間： 2013-10-07
上傳用戶：1583060504
Today’s computer, datacom, and telecom systems demandpower supplies that are effi cient, respond quicklyto load transients and accurately regulate the voltageat the load. For example, load current can be measuredby using the inductor DCR, thus eliminating the needfor a dedicated sense resistor. Inductor DCR sensingincreases effi ciency—especially at heavy load—whilereducing component cost and required board space.The LTC®3856 single-output 2-phase synchronous buckcontroller improves the accuracy of inductor DCR sensingby compensating for changes in DCR due to temperature.
上傳時間： 2013-11-05
上傳用戶：guobing703
Once relegated to the hinterlands of low cost indicatorlights, the LED is again in the spotlight of the lightingworld. LED lighting is now ubiquitous, from car headlightsto USB-powered lava lamps. Car headlights exemplifyapplications that capitalize on the LED’s clear advantages—unwavering high quality light output, tough-assteelrobustness, inherent high effi ciency—while a USBlava lamp exemplifi es applications where only LEDs work.Despite these clear advantages, their requirement forregulated voltage and current make LED driver circuitsmore complex than the venerable light bulb, but some newdevices are closing the gap. For instance, the LTM®8040μModule™ LED driver integrates all the driver circuitryinto a single package, allowing designers to refocus theirtime and effort on the details of lighting design criticalto a product’s success.
上傳時間： 2013-10-16
上傳用戶：togetsomething
High voltage buck DC/DC controllers such as the LTC3890(dual output) and LTC3891 (single output) are popular inautomotive applications due to their extremely wide 4V to60V input voltage range, eliminating the need for a snubberand voltage suppression circuitry. These controllersare also well suited for 48V telecom applications whereno galvanic isolation is required.
上傳時間： 2013-10-31
上傳用戶：wwwe
<li id="qaaks"></li>