The LTC®4099 high effi ciency USB power manager andLi-Ion/Polymer battery charger seamlessly managespower distribution from multiple sources in portableapplications. It is differentiated from other USB powermanagers by its bidirectional I2C port that allows the hostmicroprocessor to control and monitor all aspects of theUSB power management and battery charging processes.In addition, a programmable interrupt generation functionalerts the host microprocessor to changes in device statusand provides unprecedented control of power managementfunctions. This high degree of confi gurability allowspost-layout changes in operation, even changes in thefi eld, and it allows a single qualifi ed device to be usedin a variety of products, thus reducing design time andeasing inventory management.
Abstract: As electronic systems take over many of the mechanical functions in a car—ranging from engine timing to steering andbraking—there is a growing concern about fault tolerance. There should not be a single point of failure that would prevent a car fromat least "limping" off the road or making it to the nearest service station. Redundant systems, watchdog timers, and other controlcircuits are used to reroute signals and perform other functions that ensure that a vehicle can safely make it off the road when afailure occurs.
As logic systems get larger and more complex, theirsupply current requirements continue to rise. Systemsrequiring 100A are fairly common. A high current powersupply to meet such requirements usually requires parallelingseveral power regulators to alleviate the thermalstress on the individual power components. A powersupply designer is left with the choice of how to drive theseparalleled regulators: brute-force single-phase or smartPolyPhaseTM.
Notebook and palmtop systems need a multiplicity ofregulated voltages developed from a single battery. Smallsize, light weight, and high efficiency are mandatory forcompetitive solutions in this area. Small increases inefficiency extend battery life, making the final productmuch more usable with no increase in weight. Additionally,high efficiency minimizes the heat sinks needed onthe power regulating components, further reducing systemweight and size.
為了改變目前電網現場作業管理的變電巡檢、變電檢修試驗、輸電線路巡檢檢修等管理系統各自獨立運行，信息不能共享，功能、效率受限，建設和維護成本高的現狀，提出了采用B/S+C/S構架模式，將各現場作業管理模塊和生產MIS（管理系統）集成為一體的現場作業管理系統的設計方案，做到各子系統和生產MIS軟硬資源共享，做到同一數據唯一入口、一處錄入多處使用。各子系統設備人員等基礎信息來源于生產管理系統，各子系統又是生產管理系統的作業數據、缺陷信息的重要來源。經過研究試用成功和推廣應用，目前該系統已在江西電網220 kV及以上變電站全面應用。
Abstract:
In order to improve the status that the substation field inspection system， substation equipments maintenance and testing system， power-line inspection and maintenance system are running independent with each other. They can?蒺t share the resource information which accordingly constrains their functions and efficiency， and their construction and maintenance costs are high. This paper introduces a field standardized work management system based on B/S+C/S mode， integrating all field work management systems based on MIS and share the equipments and employee?蒺s data of MIS，the field work data of the sub systems are the source information of MIS， by which the same single data resouce with one-time input can be utilized in multiple places. After the research and testing， this system is triumphantly using in all 220kV and above substations in Jiangxi grid.
When a system designer specifies a nonisolated dc/dc powermodule, considering the needed input voltage range isequally as important as considering the required performanceattributes and features. Generally, nonisolated moduleshave either a narrow or a wide input voltage range. Narrowinputmodules typically have a nominal input voltage of3.3, 5, or 12 V. For systems that operate from a tightlyregulated input bus—such as those that do not use batterybackup—a narrow-input module is often adequate sincethe input remains fairly stable.Offering greater flexibility, wide-input modules operatewithin a range of 7 to 36 V, which includes the popular12- or 24-V industrial bus. This enables a single module tobe used for generating multiple voltages. These modulesare ideal for industrial controls, HVAC systems, vehicles,medical instrumentation, and other applications that usea loosely regulated distribution bus. In addition, systemspowered by a rectifier/battery charger with lead-acidbattery backup almost always require wide-input modules.System designers who choose power supplies may wantto take a close look at the latest generation of wide-inputdc/dc modules.
Features: High efficiency, high reliability, low cost AC input range selected by switch 100% full load burn-in test Protections: Short circuit / Over load Fixed switching frequency at 25KHz Cooling by free air convection 1 year warranty Dimensions: 199*98*38mm (L*W*H)
The P89LPC912/913/914 are single-chip microcontrollers in low-cost 14-pin packages, based on a high performance processor architecture that executes instructions in two to four clocks, six times the rate of standard 80C51 devices. Many system level functions have been incorporated into the P89LPC912/913/914 in order to reduce component count, board space, and system cost.
為解決電致變色器件的顏色變化受外界環境顏色控制的問題，設計了一種基于單片機的便攜式顏色自適應識別電路。與傳統顏色識別電路相比較，該電路利用數字式的顏色傳感器來獲取外界環境顏色，產生的數字顏色信號易于單片機進行處理。在電路中，下位機部分主要負責獲取電致變色器件變色參數及控制電致變色器件的顏色變化;而上位機部分主要負責把下位機獲取的電致變色器件變色參數進行電壓到顏色的曲線擬合，并通過藍牙通信把擬合曲線參數傳遞給下位機。結果表明，該電路能自動根據環境顏色提供-4~4 V范圍步進為0.1 V的電壓來驅動電致變色器件的顏色顯示，與傳統的顏色識別電路設計相比，識別的精度和速度都得到了明顯改善。
Abstract:
In this paper， a portable adaptive circuit for color identification(PACCI) based on MCU was designed. Compared to the traditional color identification circuit， the PACCI adopts digital sensor to detect the color data from external environment and further generate digital color data， which can be processed easily by MCU. In PACCI， the slave is mainly responsible for detecting the color parameters of the corresponding elcreochromic device and further driving it. For the master， which is mainly responsible for the color curve fitting based on the parameters of the electrochromic device， and transmits the fitting parameters to the slave through the bluetooth device. The results show that the PACCI can provide the basis voltage range from -4V to 4V automatically based on the colors of external environment with step as 0.1V to drive the corresponding electrochromic device. Compared to the traditional color recognition circuit， the recognition accuracy and speed of PACCI have been improved significantly.
為提高溫度測量效率，降低系統的成本，擴展傳輸距離，設計出一種新型溫度采集系統。單片機通過控制具有單總線方式的溫度傳感器DS18B20實現對溫度的測量，同時單片機通過控制具有單總線方式300～450MHz頻率范圍內的MAX7044與MAX7033無線發射與接收芯片實現溫度數據的無線傳輸。與傳統溫度采集系統相比，該系統利用單總線方式連接，采用無線傳輸方式實現遠距離通信，易于系統的集成與擴展。實驗結果表明，該系統結構簡單、方便移植，能夠同時實現多達上百點溫度的測量與500m范圍的傳輸。
Abstract:
To improve the temperature measurement efficiency and reduce system cost,expansion of transmission distance,a new type of temperature acquisition system is designed.Microcontroller controlled temperature sensor DS18B20which has a single-bus achieves temperature measurement,while microcontroller by controlled the MAX7044and MAX7033chip with a single-bus and having300~450MHz radiofrequency to achieve the wireless transmission of temperature data.Compared with conventional temperature acquisition system,the system uses single-bus connected,and uses wireless transmission means to achieve long-distance communications,easy-to-system integration and expansion.The experimental results show that the system is simple,convenient transplantation,and can be implemented in as many as a hundred-point temperature measure-ment and the transmission range of500meters.
