Portable, battery-powered operation of electronic apparatushas become increasingly desirable. Medical, remotedata acquisition, power monitoring and other applicationsare good candidates for battery operation. In some circumstances,due to space, power or reliability considerations,it is preferable to operate the circuitry from a single 1.5Vcell. Unfortunately, a 1.5V supply eliminates almost alllinear ICs as design candidates. In fact, the LM10 opamp-reference and the LT®1017/LT1018 comparators arethe only IC gain blocks fully specifi ed for 1.5V operation.Further complications are presented by the 600mV dropof silicon transistors and diodes. This limitation consumesa substantial portion of available supply range, makingcircuit design diffi cult. Additionally, any circuit designedfor 1.5V operation must function at end-of-life batteryvoltage, typically 1.3V. (See Box Section, “Componentsfor 1.5V Operation.”)
標簽： Circuitry Operation Single 1017
上傳時間： 2013-12-20
上傳用戶：Wwill
DC-link Automotive: MKP1849 (Customized)電動汽車電驅直流母線電容（顧客訂制品）MKP1849系列.MKP1849-可集成母線排，大大降低了寄生電感，提高了系統穩定性。
上傳時間： 2013-10-13
上傳用戶：nanfeicui
Portable, battery-powered operation of electronic apparatushas become increasingly desirable. Medical, remotedata acquisition, power monitoring and other applicationsare good candidates for batteryoperation. In some circumstances,due to space, power or reliability considerations,it is preferable to operate the circuitry from a single 1.5Vcell. Unfortunately, a 1.5V supply eliminates almost alllinear ICs as design candidates. In fact, the LM10 opamp-reference and the LT®1017/LT1018 comparators arethe only IC gain blocks fully specifi ed for 1.5V operation.Further complications are presented by the 600mV dropof silicon transistors and diodes. This limitation consumesa substantial portion of available supply range, makingcircuit design diffi cult. Additionally, any circuit designedfor 1.5V operation mustfunction at end-of-life batteryvoltage, typically 1.3V. (See Box Section, “Componentsfor 1.5V Operation.”)
標簽： Circuitry Operation Single Cell
上傳時間： 2013-10-30
上傳用戶：hz07104032
J-Link V8個人使用經驗寫成的用戶手冊
上傳時間： 2013-10-07
上傳用戶：hulee
教你如何制作一個J-Link V8仿真器！ 已經成功！
上傳時間： 2013-10-15
上傳用戶：truth12
介紹一種人機交互系統的可靠性設計方案。該系統基于Memory-link通信協議，采用了目前流行的基于ARM7架構的S3C44BOX作為主控芯片，通過RS-422實現人機交互通信。結合抗干擾的硬件設計和穩定有效運行的軟件設計方案，實現了在強干擾下穩定可靠的通信。實驗結果表明，本系統抗干擾能力強、運行穩定可靠，在自主開發控制系統的人機交互通信部分具有一定的參考價值。
標簽： Memory-link 協議 人機交互系統 可靠性設計
上傳時間： 2013-11-21
上傳用戶：cknck
J-LINK仿真器詳細教程 flash下載操作等
上傳時間： 2013-11-14
上傳用戶：JamesB
本文主要介紹MDK4.10下，連接ST-Link II的設置方法，給出了所有所需的配置文件。
上傳時間： 2013-11-22
上傳用戶：kang1923
The NCV7356 is a physical layer device for a single wire data linkcapable of operating with various Carrier Sense Multiple Accesswith Collision Resolution (CSMA/CR) protocols such as the BoschController Area Network (CAN) version 2.0. This serial data linknetwork is intended for use in applications where high data rate is notrequired and a lower data rate can achieve cost reductions in both thephysical media components and in the microprocessor and/ordedicated logic devices which use the network.The network shall be able to operate in either the normal data ratemode or a high-speed data download mode for assembly line andservice data transfer operations. The high-speed mode is onlyintended to be operational when the bus is attached to an off-boardservice node. This node shall provide temporary bus electrical loadswhich facilitate higher speed operation. Such temporary loads shouldbe removed when not performing download operations.The bit rate for normal communications is typically 33 kbit/s, forhigh-speed transmissions like described above a typical bit rate of83 kbit/s is recommended. The NCV7356 features undervoltagelockout, timeout for faulty blocked input signals, output blankingtime in case of bus ringing and a very low sleep mode current.
上傳時間： 2013-10-24
上傳用戶：s藍莓汁
CC-link系統小型IO模塊用戶手冊（詳細篇）
上傳時間： 2015-01-02
上傳用戶：a82531317
