The aim of this diploma thesis is to implement all compulsory features of the WiMAX OFDM physical layer SPECIFIED in IEEE 802.16-2004 in Matlab Simulink.
標簽： compulsory implement features physical
上傳時間： 2016-09-28
上傳用戶：zyt
DSR-UU is a DSR implementation that runs in Linux and in the ns-2 network simulator. DSR-UU implements most of the basic DSR features SPECIFIED in the DSR draft (version 10). One big exception is flow extensions. DSR-UU does NOT use ARP, so do not be surprised if you do not see ARP traffic. DSR-UU instead uses its own neighbor table that sets up the MAC-to-IP translation during route discovery.
標簽： DSR-UU implementation simulator network
上傳時間： 2016-11-06
上傳用戶：er1219
The TMS320C54x, TMS320LC54x, and TMS320VC54x fixed-point, digital signal processor (DSP) families (hereafter referred to as the ’54x unless otherwise SPECIFIED) are based on an advanced modified Harvard architecture that has one program memory bus and three data memory buses. These processors also provide an arithmetic logic unit (ALU) that has a high degree of parallelism, application-specific hardware logic, on-chip memory, and additional on-chip peripherals. These DSP families also provide a highly specialized instruction set, which is the basis of the operational flexibility and speed of these DSPs.
標簽： TMS 320 fixed-point processor
上傳時間： 2013-12-27
上傳用戶：宋桃子
A UML Documentation for an Elevator System：This paper is a PhD project report for the course Distributed Embedded Systems at Carnegie Mellon University. Throughout this course, a distributed real-time system – an elevator control system– is SPECIFIED, designed, built, and simulated. Object Oriented Analysis and Design methods, in specific the Unified Modeling Language (UML) are used when designing the system.
標簽： Documentation for Elevator Distrib
上傳時間： 2013-12-14
上傳用戶：zhouli
*** *** *** *** *** *** ***** ** Two wire/I2C Bus READ/WRITE Sample Routines of Microchip s ** 24Cxx / 85Cxx serial CMOS EEPROM interfacing to a ** PIC16C54 8-bit CMOS single chip microcomputer ** Revsied Version 2.0 (4/2/92). ** ** Part use = PIC16C54-XT/JW ** Note: 1) All timings are based on a reference crystal frequency of 2MHz ** which is equivalent to an instruction cycle time of 2 usec. ** 2) Address and literal values are read in octal unless otherwise ** SPECIFIED.
標簽： Microchip Routines Sample WRITE
上傳時間： 2013-12-27
上傳用戶：ljmwh2000
ABC_FDTD_Die(T) Implements simulation of a Gaussian Pulse over T time steps. ABC are for free space. If boundaries are in the Dielectric medium then the ABC fail. Dielectric medium begin and end can be SPECIFIED with the code
標簽： ABC_FDTD_Die Implements simulation Gaussian
上傳時間： 2013-12-22
上傳用戶：caiiicc
ABC_FDTD_Die(T) Implements simulation of a Gaussian Pulse over T time steps. ABC are for free space. If boundaries are in the Dielectric medium then the ABC fail. Dielectric medium begin and end can be SPECIFIED with the code
標簽： ABC_FDTD_Die Implements simulation Gaussian
上傳時間： 2014-07-27
上傳用戶：LIKE
The combinatorial core of the OVSF code assignment problem that arises in UMTS is to assign some nodes of a complete binary tree of height h (the code tree) to n simultaneous connections, such that no two assigned nodes (codes) are on the same root-to-leaf path. Each connection requires a code on a SPECIFIED level. The code can change over time as long as it is still on the same level. We consider the one-step code assignment problem: Given an assignment, move the minimum number of codes to serve a new request. Minn and Siu proposed the so-called DCAalgorithm to solve the problem optimally. We show that DCA does not always return an optimal solution, and that the problem is NP-hard. We give an exact nO(h)-time algorithm, and a polynomial time greedy algorithm that achieves approximation ratio Θ(h). Finally, we consider the online code assignment problem for which we derive several results
標簽： combinatorial assignment problem arises
上傳時間： 2014-01-19
上傳用戶：BIBI
Reads/writes text as a character stream, buffering characters so as to provide for the efficient reading/writing of characters, arrays, and lines. The buffer size may be SPECIFIED, or the default size may be used. The default is large enough for most purposes. In general, each read request made of a Reader causes a corresponding read request to be made of the underlying character or byte stream. It is therefore advisable to wrap a BufferedReader around any Reader whose read() operations may be costly, such as FileReaders and InputStreamReaders.
標簽： characters character buffering efficient
上傳時間： 2017-02-20
上傳用戶：cjl42111
The BNL toolbox is a set of Matlab functions for defining and estimating the parameters of a Bayesian network for discrete variables in which the conditional probability tables are SPECIFIED by logistic regression models. Logistic regression can be used to incorporate restrictions on the conditional probabilities and to account for the effect of covariates. Nominal variables are modeled with multinomial logistic regression, whereas the category probabilities of ordered variables are modeled through a cumulative or adjacent-categories response function. Variables can be observed, partially observed, or hidden.
標簽： estimating parameters functions defining
上傳時間： 2014-12-05
上傳用戶：天誠24
蟲蟲下載站版權所有 京ICP備2021023401號-1
