本文依據集成電路設計方法學，探討了一種基于標準Intel 8086 微處理器的單芯片計算機平臺的架構。研究了其與SDRAM，8255 并行接口等外圍IP 的集成，并在對AMBA協議和8086 CPU分析的基礎上，采用遵從AMBA傳輸協議的系統總線代替傳統的8086 CPU三總線結構，搭建了基于8086 IP 軟核的單芯片計算機系統，并實現了FPGA 功能演示。關鍵詞：微處理器； SoC；單芯片計算機；AMBA 協議
Design of 8086 CPU Based Computer-on-a-chip System（School of Electrical Engineering and Automation, Heifei University of Technology, Hefei, 230009,China）Abstract: According to the IC design methodology, this paper discusses the design of one kind of Computer-on-a-chip system architecture, which is based on the standard Intel8086 microprocessor,investigates how to integrate the 8086 CPU and peripheral IP such as, SDRAM controller, 8255 PPI etc. Based on the analysis of the standard Intel8086 microprocessor and AMBA Specification,the Computer-on-a-chip system based on 8086 CPU which uses AMBA bus instead of traditional three-bus STRUCTURE of 8086 CPU is constructed, and the FPGA hardware emulation is fulfilled.Key words: Microprocessor; SoC; Computer-on-a-chip; AMBA Specification
基于單片機的除塵控制器的設計:介紹通用控制儀的硬件組成和軟件設計,闡述了系統的性能指標和功能特點。該產品功能完善,可靠性高,具有很好的應用前景。關鍵詞: 除塵器;通用控制儀;單片機;系統設計
Abstract: The hardware STRUCTURE and the software design are introduced in this paper, and the performance index and the features of the system are expounded. It has comp rehensive functions, high reliability and good app lication.Key words: dust catcher; universal controller; microcontroller; system design
一種基于ST62單片機的稱重顯示控制器A Weighing Display Controller Based on ST62 Single Chip Computer祛 FA(上海時博飛奧控制系統有限公司，上海201100)摘要在介紹了基于ST62單片機的基礎上，詳細描述了稱重顯控制器的硬件設計和軟件設計思路。該控制器結構簡單、操作方便、抗擾能力強等優點;具有較好的推廣應用價值。關鍵詞稱重顯示控制儀ST62單片機硬件設計軟件設計Abstract Ont heb asiso fin torductiono fST 62s inglec hipc omputer,th ed esignc oncrptof h ardwarea nds oftwarefo rw eighingd isplayc ontorleris d escrbed.The controler features simple STRUCTURE, ease operation, powerful capability of anti-interference, etc.，it is wealth to be promoted into practicalapplicationsKeywords We妙噸display0 引言ST62s inglec hip Hardwared esign Softwaer design備 份 振 蕩器，振蕩器保護電路，上電復位及低壓檢測復稱 重 顯 示控制器是一種具有數字顯示、開關量輸出、定值控制和通信功能的以微機為操作核心的稱重控制裝置。它是電子衡器的重要基礎部件，直接影響電子衡器及電子稱重系統的功能和性能。與合適的傳感器及承重傳力復位系統組合可組成配料秤、料斗秤、定值秤、平臺秤、汽車秤等，廣泛應用于電力、化工、建筑、冶金、交通運輸、食品、軍工等部門，是進行自動稱重配料控制和生產過程自動化必不可少的重要檢測、控制裝置。隨著 稱 重 計量自動化水平的提高，對稱重顯示控制器的要求也越來越高。為實現低漂移、高穩定，本控制器采用低漂移、高增益放大器AD620和高分辨率的A/D轉換器CS5550。為提高穩定性和可靠性，采用集成度高的、抗干擾能力強的ST62單片機。
針對運行中火車測速運用多普勒效應采用DSP 設計雷達測速系統并闡述了其基本設計思想與工作原理給出系統硬件軟件設計結構和原理圖改善了原有光電測速精度提高了系統工作穩定性和可靠性經實驗證明DSP 采集板工作穩定測速效果好關鍵詞DSP; 雷達測速; 多普勒效應
On Board DSP-Based Radar Speed Measurement System TANG Wei, SUN Zhi-fang, CHEN Quan (Dept.of computer Science,Yangtze University,Jingzhou 434023,China)Abstract: This paper presents a DSP-based train speed measurement by using Doppler radar. The STRUCTURE of the system is introduced.The hardware and software are also discussed.Key words: DSP; rader speed measurement; doppler principle
1 Communication Protocol (Computer as master)
The communication protocol describes here allows your computer to access 4096 internal registers (W0000-W4095) and 1024 internal relays (B0000-B1023) in the Workstation..
1.1 Request Message Format
Request message is a command message to be sent from the computer to the Workstation. The data STRUCTURE of request message is shown below. Note that numbers are always in hexadecimal form and converted into ASCII characters. For example, Workstation unit number 14 will appear in the message as character 0(30h) followed by character E(45h); a BCC of 5Ah will appear in the message as character 5(35h) followed by character A(41h).
This application note describes a reference system which illustrates how to build an embeddedPowerPC® system using the Xilinx 1-Gigabit Ethernet Media Access Controller processor core.This system has the PLB_Gemac configured to use Scatter/Gather Direct Memory Access andthe Serializer/Deserializer (SerDes) interface. This application note describes how to set up thespecific clocking STRUCTURE required for the SerDes interface and the constraints to be added tothe UCF file. This reference system is complete with a standalone software application to testsome of the main features of this core, including access to registers, DMA capabilities, transmitand receive in loopback mode. This reference system is targeted for the ML300 evaluationboard.
Abstract: With industrial/scientific/medical (ISM) band radio frequency (RF) products, often times users are new to the STRUCTURE of Maxim's low pin-count transmitters andfully integrated superheterodyne receivers. This tutorial provides simple steps that can be taken to get the best performance out of these transmitters and receivers whileproviding techniques to measure the overall capability of the design.
The super-junction STRUCTURE, which has P-type pillar layers as shown left,
realizes high withstand voltage and ON-resistance lower than the conventional
theoretical limit of silicon.
Calculation of the Differential Impedance of Tracks on FR4 substrates
There is a discrepancy between calculated and measured values of impedance for differential transmission lineson FR4. This is especially noticeable in the case of surface microstrip configurations. The anomaly is shown tobe due to the nature of the substrate material. This needs to be considered as a layered STRUCTURE of epoxy resinand glass fibre. Calculations, using Boundary Element field methods, show that the distribution of the electricfield within this layered STRUCTURE determines the apparent dielectric constant and therefore affects theimpedance. Thus FR4 cannot be considered to be uniform dielectric when calculating differential impedance.
