The acceptance and introduction of serial communication to more and more applications has led to requirements that the assignment of message identifiers to communication functions be standardized for certain applications. These applications can be realized with CAN more comfortably, if the address range that originally has been defined by 11 identifier bits is enlarged
標簽： more communication introduction applications
上傳時間： 2014-01-04
上傳用戶：小草123
TC35i新版西門子工業GSM模塊是一個支持中文短信息的工業級GSM模塊,工作在EGSM900和GSM1800雙頻段,電源范圍為直流3.3～4.8V ,電流消耗——休眠狀態為3.5mA，空閑狀態為25mA，發射狀態為300mA(平均)，2.5A峰值；可傳輸語音和數據信號, 功耗在EGSM900(4類)和GSM1800(1類)分別為2W和1W ,通過接口連接器和天線連接器分別連接SIM卡讀卡器和天線。SIM電壓為3V/1.8V，TC35i的數據接口(CMOS電平)通過AT命令可雙向傳輸指令和數據,可選波特率為300b/s～115kb/s , 自動波特率為1.2kb/s～115kb/s。它支持Text和PDU格式的SMS(Short Message Service,短消息),可通過AT命令或關斷信號實現重啟和故障恢復
上傳時間： 2016-08-26
上傳用戶：fnhhs
gps matlab 仿真程序（A collection of geodetic functions that solve a variety of problems in geodesy. Supports a wide range of common and user-defined reference ellipsoids. Most functions are vectorized.）
標簽： collection functions geodetic problems
上傳時間： 2014-12-07
上傳用戶：whenfly
RECOMMENDATION ITU-R M.1653*,** Operational and deployment requirements for wireless access systems including radio local area networks in the mobile service to facilitate sharing between these systems and systems in the Earth exploration-satellite service (active) and the space research service (active) in the band 5 470-5 570 MHz within the 5 460 5 725 MHz range
標簽： RECOMMENDATION requirements Operational deployment
上傳時間： 2016-10-21
上傳用戶：miaochun888
Top module name : SHIFTER (File name : SHIFTER.v) 2. Input pins: SHIFT [3:0], IN [15:0], SIGN, RIGHT. 3. Output pins: OUT [15:0]. 4. Input signals generated from test pattern are latched in one cycle and are synchronized at clock rising edge. 5. The SHIFT signal describes the shift number. The shift range is 0 to 15. 6. When the signal RIGHT is high, it shifts input data to right. On the other hand, it shifts input data to left. 7. When the signal SIGN is high, the input data is a signed number and it shifts with sign extension. However, the input data is an unsigned number if the signal SIGN is low. 8. You can only use following gates in Table I and need to include the delay information (Tplh, Tphl) in your design.
上傳時間： 2013-12-13
上傳用戶：himbly
Top module name : SHIFTER (File name : SHIFTER.v) 2. Input pins: SHIFT [3:0], IN [15:0], SIGN, RIGHT. 3. Output pins: OUT [15:0]. 4. Input signals generated from test pattern are latched in one cycle and are synchronized at clock rising edge. 5. The SHIFT signal describes the shift number. The shift range is 0 to 15. 6. When the signal RIGHT is high, it shifts input data to right. On the other hand, it shifts input data to left. 7. When the signal SIGN is high, the input data is a signed number and it shifts with sign extension. However, the input data is an unsigned number if the signal SIGN is low. 8. You can only use following gates in Table I and need to include the delay information (Tplh, Tphl) in your design.
上傳時間： 2014-01-20
上傳用戶：三人用菜
短信發送實現gprs貓發送短信息，wap push，push load，免提短信源代碼.-gprs cat achieve this short message, WAP push, push load. Handsfree SMS source code
上傳時間： 2014-01-21
上傳用戶：cooran
Produce Java classes to calculate and display the root of a quadratic equation when input the coefficients a, b and c within the range of -100 to 100 by user.
標簽： calculate the quadratic equation
上傳時間： 2014-01-17
上傳用戶：aappkkee
Produce Java classes to calculate and display the Poisson probability when input the value of the average (A) arrival rate of customers at some business in the range of 1 to 10. The error message will output when A is out of the range。
標簽： the probability calculate Produce
上傳時間： 2014-01-10
上傳用戶：moerwang
This GUI can be used by entering nu at the MATLAB command prompt. The user can either select a function (f(x)) of their choice or a statistical distribution probability distribution function to plot over a user defined range. The function s integral can be evaluated over a user defined range by using: The composite trapezium, simpsons and gauss-legendre rules. This is useful for calculating accurate probabilities that one might see in statistical tables.
標簽： can entering command MATLAB
上傳時間： 2016-11-07
上傳用戶：偷心的海盜
