The design and manufacturing of wireless radio frequency (RF) transceivers has developed rapidly in recent ten
yeas due to rapid development of RF integrated circuits and the evolution of high-speed digital signal
processors (DSP). Such high speed signal processors, in conjunction with the development of high resolution
analog to digital converters and digital to analog converters, has made it possible for RF designers to digitize
higher intermediate frequencies, thus reducing the RF section and enhancing the overall performance of the RF
section.
The continued reduction of integrated circuit feature sizes and
commensurate improvements in device performance are fueling the progress
to higher functionality and new application areas. For example, over the last
15 years, the performance of microprocessors has increased 1000 times.
Analog circuit performance has also improved, albeit at a slower pace. For
example, over the same period the speed/resolution figure-of-merit of
analog-to-digital converters improved by only a factor 10.
Wireless technologies like GSM, UMTS, LTE, Wireless LAN and Bluetooth have
revolutionized the way we communicate by making services like telephony and Internet
access available anytime and from almost anywhere. Today, a great variety of technical
publications offer background information about these technologies but they all fall
short in one way or another. Books covering these technologies usually describe only
one of the systems in detail and are generally too complex as a first introduction. The
Internet is also a good source, but the articles one finds are usually too short and super-
ficial or only deal with a specific mechanism of one of the systems. For this reason, it
was difficult for me to recommend a single publication to students in my telecommunication
classes, which I have been teaching in addition to my work in the wireless telecommunication
industry. This book aims to change this.
M.NT68676.2A is a monitor control board, which is suitable for Asia-Pacific market. It can supportLED/LCD panels which resolution is up to 2048×1152.M.NT68676.2A can synchronize with computer automatically. Synchronization requires thesynchronous signal which horizontal and vertical sync are separated.M.NT68676.2A can support dynamic contrast control, headphone input and Digital volume controlsimultaneously.
該步進電機驅動器又稱為EasyDriver，EasyDriver能夠為兩級步進電機提供大約每相750mA（兩極一共1.5A）的驅動。它默認設置為8步細分模式（所以如果你的電機是每圈200步，你使用EasyDriver時默認為每圈1600步），更多細分模式可以通過將MS1或MS2兩個接腳接地進行設置。這是一種基于Allegro A3967驅動芯片的細分斷路器。對于此設計的完整規格，請查閱A3967的參數表。它的最大每相電流從150mA到750mA?？梢圆捎玫淖畲篁寗与妷捍蟾攀?0V，其中包括板載5V的調壓器，所以只需要一個電源。質優價廉，這玩意兒只要十幾美元，比你自己制作電路板更便宜。步進電機驅動器設計特色：· A3967 Microstepping Driver· MS1 and MS2 pins broken out to change microstepping resolution to full, half, quarter and eighth steps (defaults to eighth)· Compatible with 4, 6, and 8 wire stepper motors of any voltage· Adjustable current control from 150mA/phase to 700mA/phase· Power supply range from 6V to 30V. The higher the voltage, the higher the torque at high speeds
ICN6201/02 is a bridge chip which receives MIPI? DSI inputs and sends LVDS outputs.
MIPI? DSI supports up to 4 lanes and each lane operates at 1Gbps maximum; the totally maximum input
bandwidth is 4Gbps; and the MIPI defined ULPS(ultra-low-power state) is also supported. ICN6201 decodes
MIPI? DSI 18bepp RGB666 and 24bpp RGB888 packets.The LVDS output 18 or 24 bits pixel with 25MHz to 154MHz, by VESA or JEIDA format.ICN6201/02 support video resolution up to FHD (1920x1080) and WUXGA (1920x1200).ICN6201 adopts QFN48 package and ICN6202 adopts QFN40 package
