This program requires the DSP2833x header files. // // This program requires an external I2C RTC connected to // the I2C bus at address 0x6f. // // As supplied, this project is configured for "boot to SARAM" // operation. The 2833x Boot Mode table is shown below. // For information on configuring the boot mode of an eZdsp, // please refer to the documentation included with the eZdsp,
標簽： requires program This external
上傳時間： 2017-07-12
上傳用戶：dianxin61
This program requires the DSP2833x header files. // // As supplied, this project is configured for "boot to SARAM" // operation. The 2833x Boot Mode table is shown below. // For information on configuring the boot mode of an eZdsp, // please refer to the documentation included with the eZdsp,
標簽： configured requires supplied program
上傳時間： 2014-01-10
上傳用戶：lixinxiang
This software is developed to provide ease with controller design. For PID control, options are given to design and analyse the compensated and uncompensated system. You are free to choice among Proportional PI, PD and PID mode of control. Both frequency and time domain characteristics can be observed. Special Menus are given to observe time and frequency response plots. For Statefeedback controller similar options are given. But this is limited to second order system only.
標簽： controller developed software control
上傳時間： 2017-07-25
上傳用戶：aysyzxzm
Blocking CoThe aim of this toolbox is to compute blocking probabilities in WDM networks. This work was based on [1], [2], [3], [4] and user is referred to those papers for deeper study. Because WDM networks are circuit switched loss networks blocking may occur because of lack of resources.Computation in WDM Networks Toolbox
標簽： probabilities Blocking blocking networks
上傳時間： 2014-01-14
上傳用戶：iswlkje
RS_latch using vhdl, When using static gates as building blocks, the most fundamental latch is the simple SR latch, where S and R stand for set and reset. It can be constructed from a pair of cross-coupled NOR (Not OR) logic gates. The stored bit is present on the output marked Q. Normally, in storage mode, the S and R inputs are both low, and feedback maintains the Q and Q outputs in a constant state, with Q the complement of Q. If S (Set) is pulsed high while R is held low, then the Q output is forced high, and stays high when S returns to low similarly, if R (Reset) is pulsed high while S is held low, then the Q output is forced low, and stays low when R returns to low.
標簽： using fundamental the RS_latch
上傳時間： 2017-07-30
上傳用戶：努力努力再努力
hese are the zip files that are associated with application note ADSP-BF533 Blackfin Booting Process (EE-240) example.zip: Used throughout the EE-note to explain in detail the various booting modes. BF533 Ez Kit Multiple DXE Boot.zip: Multi-DXE Boot Example used with the ADSP-BF533 Ez-Kit Lite. Host Boot.zip: Example Host code to demonstrate SPI Slave Mode Booting Program_Atmel.zip: Example code that programs the Atmel DataFlashes via an ADSP-BF532 Processor All programs have been written for VisualDSP++ 3.5
標簽： application associated are Blackfin
上傳時間： 2017-07-30
上傳用戶：tonyshao
This is a simulator written in Tcl to simulate a network node carrying GSM and GPRS traffics with QoS mechanisms. The payload type including circuit-switched voice, VoIP and web traffic, and the performance including packet drop, delay can be analyzed. The implemented QoS mechanism is DiffServ, with 4 RED queues for different services with different priorities.
標簽： simulator carrying simulate traffics
上傳時間： 2014-01-01
上傳用戶：1583060504
Complete coverage of all four CCNP exams: ? EIGRP, OSPF, IS-IS, and BGP ? Optimizing routing ? IP multicast ? IPv6 ? VLAN implementation ? Spanning Tree ? InterVLAN routing ? Layer 3 redundancy ? Wireless LANs ? VoIP in campus networks ? Campus network security ? Frame-mode MPLS ? IPsec ? Cisco device hardening ? Cisco IOS? threat defenses ? Cisco VoIP ? QoS and AutoQoS ? Wireless scalability
標簽： Optimizing Complete coverage routing
上傳時間： 2017-09-26
上傳用戶：cuibaigao
The TJA1040 is an advanced high speed CAN transceiver for use in automotive and general industrial applications. It supports the differential bus signal representation described in the international standard for in-vehicle high speed CAN applications (ISO11898). CAN (Controller Area Network) is the standard protocol for serial in-vehicle bus communication, particularly for Engine Management and Body Multiplexing. The TJA1040 provides a Standby mode, as known from its functional predecessors PCA82C250 and PCA82C251, but with significantly reduced power consumption. Besides the excellent low-power behavior the TJA1040 offers several valuable system improvements. Highlights are the absolute passive bus behavior if the device is unpowered as well as the excellent EMC performance.
標簽： CAN
上傳時間： 2015-03-23
上傳用戶：Yuan Lo
制作驅動程序的好工具.支持 ISA,EISA,PCI,Plug&Play 和 DMA.不需要牽涉到很低層的東西即可在很短的時間里編出驅動程序.內含教程.使用WinDriver的優點是:開發者并不需要熟悉任何內部操作系統或kernel programming或DDK及任何驅動程式.WinDriver同時允許開發者能在自己所熟悉的開發環境下,利用使用者模式(User Mode)如使用MSDEV Visual C/C++,Borland C++Builder,Delphi或任何Win32編譯器.使用WinDriver所開發的驅動程式均可用于Windows 9x,NT/2000,NT Embedded,CE Linux and Solaris等平臺.
上傳時間： 2015-06-02
上傳用戶：1663066023
