以AVR單片機ATmega8和USB接口器件PDIUSBD12為核心，基于標準的USB1.1協議，設計一種通用USB接口模塊，以滿足嵌入式系統中對USB接口的需求。對模塊的硬件電路或單片機固件程序的硬件接口層稍加修改即可用于其他各種微處理器。該模塊可為各種嵌入式系統增加USB接口,實現與USB主機系統通信。 Abstract: Based on AVR microcontroller ATmega8 and USB interface chip PDIUSBD12, a general USB interface module is designed according to USB1.1 protocol for various requirements of embedded systems. Only with few modifications in circuit or hardware abstract layer of firmware, the module can be used on many types of microprocessors. All kinds of embedded systems can realize high speed and stable communication with USB host systems, owing to the facility of this module.
上傳時間： 2014-01-08
上傳用戶：趙云興
The PCF8578 is a low power CMOS1 LCD row and column driver, designed to drive dotmatrix graphic displays at multiplex rates of 1:8, 1:16, 1:24 or 1:32. The device has40 outputs, of which 24 are programmable and configurable for the following ratios ofrows/columns: 32¤8, 24¤16, 16¤24 or 8¤32. The PCF8578 can function as a stand-alone LCDcontroller and driver for use in small systems. For larger systems it can be used inconjunction with up to 32 PCF8579s for which it has been optimized. Together these twodevices form a general purpose LCD dot matrix driver chip set, capable of driving displaysof up to 40960 dots. The PCF8578 is compatible with most microcontrollers andcommunicates via a two-line bidirectional bus (I2C-bus). Communication overhead isminimized by a display RAM with auto-incremented addressing and display bankswitching.
上傳時間： 2013-10-23
上傳用戶：頂得柱
Information in this document is subject to change without notice and does notrepresent a commitment on the part of the manufacturer. The software describedin this document is furnished under license agreement or nondisclosureagreement and may be used or copied only in accordance with the terms of theagreement. It is against the law to copy the software on any medium except asspecifically allowed in the license or nondisclosure agreement. The purchasermay make one copy of the software for backup purposes. No part of this manualmay be reproduced or transmitted in any form or by any means, electronic ormechanical, including photocopying, recording, or information storage andretrieval systems, for any purpose other than for the purchaser’s personal use,without written permission.
上傳時間： 2014-12-27
上傳用戶：Tracey
Important Notice SUNPLUS INNOVATION TECHNOLOGY INC. reserves the right to change this documentation without prior notice. Information provided by SUNPLUS INNOVATION TECHNOLOGY INC. is believed to be accurate and reliable. However, SUNPLUS INNOVATION TECHNOLOGY INC.makes no warranty for any errors which may appear in this document. Contact SUNPLUS INNOVATION TECHNOLOGY INC.to obtain the latest version of device specifications before placing your order. No responsibility is assumed by SUNPLUS INNOVATION TECHNOLOGY INC. for any infringement of patent or other rights of third parties which may result from its use. In addition, SUNPLUSIT products are not authorized for use as critical components in life support systems or aviation systems, where a malfunction or failure of the product may reasonably be expected to result in significant injury to the user, without the express written approval of SunplusIT
標簽： SUNPLUSIT Q-Writer 編程工具 使用說明書
上傳時間： 2013-10-13
上傳用戶：brain kung
Features• Complete DTMF Receiver• Low power consumption• Internal gain setting amplifier• Adjustable guard time• Central office quality• Power-down mode• Inhibit mode• Backward compatible withMT8870C/MT8870C-1Applications• Receiver system for British Telecom (BT) orCEPT Spec (MT8870D-1)• Paging systems• Repeater systems/mobile radio• Credit card systems• Remote control• Personal computers• Telephone answering machine
上傳時間： 2013-11-20
上傳用戶：mpquest
MPLAB C30用戶指南(英文) HIGHLIGHTSThe information covered in this chapter is as follows:• About this Guide• Recommended Reading• Troubleshooting• The Microchip Web Site• Development Systems Customer Notification Service• Customer Support Document LayoutThe document layout is as follows:• Chapter 1: Compiler Overview – describes MPLAB C30, development tools andfeature set.• Chapter 2: Differences between MPLAB C30 and ANSI C – describes thedifferences between the C language supported by MPLAB C30 syntax and thestandard ANSI-89 C.• Chapter 3: Using MPLAB C30 – describes how to use the MPLAB C30 compilerfrom the command line.• Chapter 4: MPLAB C30 Runtime Environment – describes the MPLAB C30runtime model, including information on sections, initialization, memory models, thesoftware stack and much more.• Chapter 5: Data Types – describes MPLAB C30 integer, floating point and pointerdata types.• Chapter 6: Device Support Files – describes the MPLAB C30 header and registerdefinition files, as well as how to use with SFR’s.• Chapter 7: Interrupts – describes how to use interrupts.• Chapter 8: Mixing Assembly Language and C Modules – provides guidelines tousing MPLAB C30 with MPLAB ASM30 assembly language modules.
上傳時間： 2013-10-21
上傳用戶：13925096126
PICkit™ 2 Microcontroller Programmer USER’S GUIDE This chapter contains general information that will be useful to know before using thePICkit™ 2 Microcontroller Programmer. Items discussed in this chapter include:• Document Layout• Conventions Used in this Guide• Warranty Registration• Recommended Reading• The Microchip Web Site• Development Systems Customer Change Notification Service• Customer Support• Document Revision History
標簽： Microcontrolle PICkit 8482
上傳時間： 2013-11-05
上傳用戶：妄想演繹師
The CAT823, CAT824, and CAT825 provide basic reset and monitoring functions for the electronic systems. Each device monitors the system voltage and maintains a reset output until that voltage reaches the device’s specified trip value and then maintains the reset output active condition until the device’s internal timer, after a minimum timer of 140ms; toallow the systems power supply to stabilize.
上傳時間： 2014-11-18
上傳用戶：BOBOniu
The PCA9516 is a BiCMOS integrated circuit intended forapplication in I2C and SMBus systems.While retaining all the operating modes and features of the I2Csystem, it permits extension of the I2C-bus by buffering both the data(SDA) and the clock (SCL) lines, thus enabling five buses of 400 pF.The I2C-bus capacitance limit of 400 pF restricts the number ofdevices and bus length. Using the PCA9516 enables the systemdesigner to divide the bus into five segments off of a hub where anysegment to segment transition sees only one repeater delay.
上傳時間： 2013-11-21
上傳用戶：q123321
The PCA9518 is a BiCMOS integrated circuit intended forapplication in I2C and SMBus systems.While retaining all the operating modes and features of the I2Csystem, it permits extension of the I2C-bus by buffering both thedata (SDA) and the clock (SCL) lines, thus enabling virtuallyunlimited buses of 400 pF.
標簽： Expandable 5channel 9518 PCA
上傳時間： 2013-10-23
上傳用戶：dumplin9
