通過對程控濾波器的理論分析，在研究MAX262的功能和單片機的SPI總線通信的基礎上，提出了基于MAX262的程控濾波器設計方案，設計了程控濾波器的軟硬件，并給出了測試結果。 Abstract: By analyzing the programmable filter,the paper puts forward a programmable filter system design based on MAS262 on basic of studying MAS262 features and SPI bus communication.Software and hardware of the programmmable filter are designed,and the test result is given.
標簽： MAX 262 程控 濾波器設計
上傳時間： 2013-11-15
上傳用戶：wxhwjf
針對材料試驗機等設備中要求測量或控制材料拉伸或壓縮的位移，一般采用光電軸角編碼器檢測位置信號，輸出正交編碼脈沖信號。若采用其他方法檢測位置信號，必然導致電路設計復雜，可靠性降低。因此，提出一種基于LS7266R1的電子式萬能材料試驗機設計方案。給出了試驗機中的控制器工作原理，LS7266R1與單片機的接口硬件設計，以及主程序軟件流程圖。巧妙地把力量傳感器，位移傳感器等機械運動狀態的壓力或拉力以及位置坐標，變成了電壓信號和電脈沖數字信號，供A/D測量和LS7266R1計數，從而實現了獨立完成材料試驗控制或通過PC機串口命令完成材料試驗控制。 Abstract: Aiming at the requirement that the displacement of the tension and compression always be tested and controlled in the equipement such as material testing machine. The position signal was tested by photoelectric axial angle coder. Therefore， the paper proposes the design of electronic universal testing machine design based on LS7266R1. If the position signal detected by other methods， will inevitably lead to the circuit design complexity， reliability decreased. The work theory of the controller， the hardware interface design between LS7266R1 and single chip， and the flow chart of main program， are presented in this paper. The signal of the compression or tension power and displacement at working， which tested by power sensor and displacement sensor especially， is changed into electric voltage and electric pulse numerical signals. And these signals can be tested by A/D and counted by LS7266R1. Finally the test of the material properties can be controlled by itself， or controlled by the COM command of PC.
上傳時間： 2013-11-02
上傳用戶：yl1140vista
介紹了MPC555與CS8900A擴展以太網的硬件設計圖。以NUCLUES PLUS操作系統為基礎，介紹了網卡軟件驅動程序的編制，給出了以太網協議包嵌入NUCLEUS PLUS操作系統的實現方法。 Abstract: The Ethernet extension hardware design of MPC555 and CS8900A are introduced,and the software driven program based on NUCLEUS PLUS operation system and the technique that Ethernet protocol embedded in NUCLEUS PLUS real operation system are discussed.
上傳時間： 2013-10-23
上傳用戶：xiehao13
介紹了基于單片機航空交流電參數測試儀的系統設計。以Silicon Labs公司的C8051F005單片機為核心設計出數據采集板，通過RS-232串口與上位機通訊。運用Lab Windows/CVI編寫的上位機軟件實現信號的檢測以及波形和數據的顯示，給出了測試儀硬件電路的組成和軟件流程圖。本系統具有硬件結構簡單、容易實現和成本低等特點，在實際應用中其穩定性、精確性均能滿足客戶要求。 Abstract: The design of aeronautics AC parameters tester based on the single-chip is introduced.The core component of data acquisition board is C8051F005 single chip of Silicon Labs Company,and communication with PC through RS-232. The signal processing software programmed with LabWindows/CVI can be used successfully to fulfill inspection of signal and display of the waveform and data. The hardware and software configuration of test instrument are provided.The hardware of the system is simple, and can be easily realized.The stability and precision of the measurement instrument are enough to meet the requirements.
標簽： C8051F005 單片機 儀的設計 參數測試
上傳時間： 2013-11-18
上傳用戶：wang5829
為解決傳統可視倒車?yán)走_(dá)視頻字符疊加器結構復雜，可靠性差，成本高昂等問題，在可視倒車?yán)走_(dá)設計中采用視頻字符發生器芯片MAX7456。該芯片集成了所有用于產生用戶定義OSD，并將其插入視頻信號中所需的全部功能，僅需少量的外圍阻容元件即可正常工作。給出了以MAX7456為核心的可視倒車?yán)走_(dá)的軟、硬件實現方案及設計實例。該方案具有電路結構簡單、價格低廉、符合人體視覺習慣的特點。經實際裝車測試，按該方案設計的可視倒車?yán)走_(dá)視場清晰、提示字符醒目、工作可靠，可有效降低駕駛員倒車時的工作強度、減少倒車事故的發生。 Abstract: A new video and text generation chip，MAX7456，was used in the design of video parking sensor in order to simplify system structure，improve reliability and reduce cost. This chip included all the necessary functions to generate user-defined OSDs and to add them into the video signals. It could be put into work with addition of just a small number of resistances and capacitors. This paper provided software and hardware implementation solutions and design example based on the chip. The system had the characteristics of simplicity in circuit structure，lower cost，and comfort for the nature of human vision. Loading road test demonstrates high video and text display quality and reliable performance，which makes the driver easy to see backward and reduces chance of accidents.
標簽： 7456 MAX 可視倒車 中的應用
上傳時間： 2013-12-10
上傳用戶：qiaoyue
針對船舶氣象儀保障維修而設計的船舶氣象儀測試系統，包括信息處理終端、主儀器檢測模塊、傳感器檢測模塊，各個模塊都采用基于AVR單片機的嵌入式系統，模塊之間通過CAN總線進行通信。結果表明，船舶氣象儀測試系統能夠快速檢測船舶氣象儀故障，與單純依靠人工方式排查故障相比，故障檢測時間縮短了60%以上。 Abstract: The test system of ship meteorological instrument was developed to satisfy the maintenance of ship meteorological instruments，which composed of information processing terminal， testing module of main instrument and testing module of sensors. Each of these modules included an embedded system based on microcontroller of AVR series and communicated with other module by CAN bus. The results show that the test system can judge the fault of ship meteorological instrument quickly and shorten the fault detection time as much as 60% compared with simple manual troubleshooting.
標簽： AVR 單片機 氣象儀 測試系統
上傳時間： 2013-11-23
上傳用戶：stvnash
介紹了一種基于MSP430系列單片機和ADXL203加速度傳感器的數字式傾角儀，它不僅可以實現水平度檢測，而且可以測量00～3600范圍內的任意傾角，分辨率可達O．1。。此外，由于該傾角儀輸出為數字結果，因此它也可以與其他的數字設備結合起來，組合成一個功能更加強大的儀器。該數字傾角儀可廣泛應用于建筑、機械、道路、橋梁、石油、煤礦和地質勘探等各種需要測量重力參考系下傾角的場合。關鍵詞：MSP430F133單片機；力敏傳感器；ADXL203加速度計；角度測量 Abstract：This paper presents a new style digital inclinometer which is developed on the basis of the MSP430F133 MCU and the ADXL203 dual axis aeeelerometer．This inclinometer not only can test levelness，but also can measure any angle between 0。and 360。with an accuracy of 0．1 O．In addition，its output is a digital result，which makes it possible to integrate itself with other digital devices to form a more functional unit．This inclinometer can be widely used in any construction site，oil field，coal-mine or geologic survey and SO on where it will provide the working people with convenience to measure any angles．Key words：MSP430F133 MCU；force sensor；ADXL203 accelerometer；angle measurement
上傳時間： 2013-11-14
上傳用戶：lizhizheng88
FEATURES400 MSPS internal clock speedIntegrated 10-bit DAC32-bit tuning wordPhase noise ≤ –120 dBc/Hz @ 1 kHz offset (DAC output)Excellent dynamic performance>75 dB SFDR @ 160 MHz (±100 kHz offset) AOUTSerial I/O control1.8 V power supplySoftware and hardware controlled power-down48-lead TQFP/EP packageSupport for 5 V input levels on most digital inputsPLL REFCLK multiplier (4× to 20×)Internal oscillator; can be driven by a single crystalPhase modulation capabilityMultichip synchronization
上傳時間： 2014-12-04
上傳用戶：axin881314
The MSP-FET430PIF is a Parallel Port interface (does not include target board) that is used to program and debug MSP430 FET tools and test boards through the JTAG interface. This interface is included in our FET tools, but sold without the development board. This interface uses a Parallel PC Port to communicate to the Debugger Software (IAR Kickstart software included) running on the PC. The interface uses the standard 14 pin header to communicate to the MSP430 device using the standard JTAG protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is extremely low power, no external power supply is required. The tool has an integrated software environment and connects directly to the PC which greatly simplifies the set-up and use of the tool. The flash development tool supports development with all MSP430 flash parts. Features MSP430 debugging interface to connect a MSP430-Flash-device to a Parallel port on a PC Supports JTAG debug protocol (NO support for Spy-Bi-Wire (2-wire JTAG) debug protocol, Spy-Bi-Wire (2-wire JTAG) is supported by MSP-FET430UIF) Parallel Port cable and a 14-conductor target cable Full documentation on CD ROM Integrated IAR Kickstart user interface which includes: Assembler Linker Limulator Source-level debugger Limited C-compiler Technical specifications: Backwardly compatable with existing FET tool boards.
上傳時間： 2013-10-26
上傳用戶：fengweihao158@163.com
常用三星單片機燒寫電壓設置參考表 燒寫電壓說明:Vdd 電壓指燒寫時加載到芯片Vdd 端子的邏輯電壓,Vpp 電壓指燒寫時加載到芯片Vpp(Test)端子的編程電壓, Vpp=12V 是編程器的默認燒寫電壓,無須特別設置. 由于編程器的默認輸出Vpp 電壓均為12V,因此在燒寫Vpp=3.3V/5.0V 的芯片時,需要對燒寫轉換適配器作以下改動:將燒寫器燒寫座引出的Vpp 端子完全空置不用, 并在適配器上將Vdd端子直接連接Vpp 端即可.當用戶采用在PCB板上燒寫方式時,建議最好能在PCB芯片端的Vpp腳并接一個104 的電容入地,可有效保護在燒寫電壓加載時板子電路共同作用產生的瞬間過壓脈沖不會輸入到Vpp 腳而造成Vpp 擊穿.S3F84K4 燒寫特別說明,由于三星半導體DATA SHEET 要求在對該芯片進行燒寫時,須在Vpp 腳加接一個101 的電容到地,因此在使用我站各款燒寫器燒寫84K4 時,須將燒寫器主板上的Vpp 端原來并接的10uf/50V-電解電容和104 電容去掉,另行并接一個101 電容入地即可.不過,據本人特別測試結果,其實不做以上處理對燒寫過程沒有任何影響, 估計可能是三星半導體對芯片有做過改版,老版本的84K4 才會有以上特別要求,新版本是沒有這個要求的.
標簽： 三星 單片機 燒寫 電壓設置
上傳時間： 2013-10-10
上傳用戶：wcl168881111111
蟲蟲下載站版權所有 京ICP備2021023401號-1
