Abstract: Most magnetic read head data sheets do not fully specify the frequency-dependent components andare often vague when specifying other key parameters. In some cases, the specifications of two very similarheads from two different manufacturers might be quite different in terms of parameters specified and omitted.The limitations in the data sheets make designing an optimum card reading system unnecessarily difficult andtime consuming. This document outlines a strategy to overcome the above shortcomings and offers guidelinesto overcome the noise issues.
上傳時間： 2013-11-13
上傳用戶：dysyase
Abstract: Many industrial/scientific/medical (ISM) band radio frequency (RF) products use crystal oscillators to generate areference for the phase-locked loop (PLL)-based local oscillator (LO). This tutorial provides a basic description of theISM-RF Crystal Calculator, which can be used to calculate various impacts on crystal frequency accuracy and startupmargin for such an LO.
上傳時間： 2013-11-15
上傳用戶：JasonC
Abstract: IC switches and multiplexers are proliferating, thanks to near-continual progress in lowering the supply voltage,incorporating fault-protected inputs, clamping the output voltage, and reducing the switch resistances. The latest of these advancesis the inclusion of precision resistors to allow two-point calibration of gain and offset in precision data-acquisition systems.
上傳時間： 2013-11-12
上傳用戶：acwme
Many applications require a clock signal to be synchronous, phase-locked, or derived fromanother signal, such as a data signal or another clock. This type of clock circuit is important in
上傳時間： 2014-12-23
上傳用戶：qq21508895
The LT®6552 is a specialized dual-differencing 75MHzoperational amplifier ideal for rejecting common modenoise as a video line receiver. The input pairs are designedto operate with equal but opposite large-signal differencesand provide exceptional high frequency commonmode rejection (CMRR of 65dB at 10MHz), therebyforming an extremely versatile gain block structure thatminimizes component count in most situations. The dualinput pairs are free to take on independent common modelevels, while the two voltage differentials are summedinternally to form a net input signal.
上傳時間： 2014-12-23
上傳用戶：13691535575
Abstract: Transimpedance amplifiers (TIAs) are widely used to translate the current output of sensors like photodiode-to-voltagesignals, since several circuits and instruments can only accept voltage input. An operational amplifier with a feedback resistor fromoutput to the inverting input is the most straightforward implementation of such a TIA. However, even this simple TIA circuit requirescareful trade-offs among noise gain, offset voltage, bandwidth, and stability. Clearly stability in a TIA is essential for good, reliableperformance. This application note explains the empirical calculations for assessing stability and then shows how to fine-tune theselection of the feedback phase-compensation capacitor.
標簽： Transimpedance Stabilize Amplifier Your
上傳時間： 2013-11-13
上傳用戶：daoyue
Photodiodes can be broken into two categories: largearea photodiodes with their attendant high capacitance(30pF to 3000pF) and smaller area photodiodes withrelatively low capacitance (10pF or less). For optimalsignal-to-noise performance, a transimpedance amplifi erconsisting of an inverting op amp and a feedback resistoris most commonly used to convert the photodiode currentinto voltage. In low noise amplifi er design, large areaphotodiode amplifi ers require more attention to reducingop amp input voltage noise, while small area photodiodeamplifi ers require more attention to reducing op amp inputcurrent noise and parasitic capacitances.
上傳時間： 2013-10-28
上傳用戶：hanbeidang
Control systems are becoming increasingly dependent on digital processing and so require sensors able to provide direct digital inputs. Sensors based on time measurement, having outputs based on a frequency or phase, have an advantage over conventional analogue sensors in that their outputs can be measured directly in digital systems by pulse counting.
上傳時間： 2013-10-08
上傳用戶：wuyuying
Highlights the LTC1062 as a lowpass filter in a phase lock loop. Describes how the loop's bandwidth can be increased and the VCO output jitter reduced when the LTC1062 is the loop filter. Compares it with a passive RC loop filter. Also discussed is the use of LTC1062 as simple bandpass and bandstop filter.
上傳時間： 2013-10-24
上傳用戶：chens000
The LM20, LM45, LM50, LM60, LM61, and LM62 are analog output temperature sensors. They have various output voltage slopes (6.25mV/°C to 17mV/°C) and power supply voltage ranges (2.4V to 10V).The LM20 is the smallest, lowest power consumption analog output temperature sensor National Semiconductor has released. The LM70 and LM74 are MICROWIRE/SPI compatible digital temperature sensors. The LM70 has a resolution of 0.125°C while the LM74 has a resolution of 0.625°C. The LM74 is the most accurate of the two with an accuracy better than ±1.25°C. The LM75 is National’s first digital output temperature sensor, released several years ago.
上傳時間： 2014-12-23
上傳用戶：yl8908
