The PCA9547 is an octal bidirectional translating multiplexer controlled by the I2C-bus.The SCL/SDA upstream pair fans out to eight downstream pairs, or channels. Only oneSCx/SDx channel can be selected at a time, determined by the contents of theprogrammable control register. The device powers up with Channel 0 connected, allowingimmediate communication between the master and downstream devices on that channel.
上傳時間： 2014-12-28
上傳用戶：270189020
The outputs of the PCA9518 are immediately available as soon as there is a voltage present on thesupply >~1V and behave as described above. The power-on reset of the PCA9518A keeps the outputsturned off during power-up and maintains the high impedance of the outputs throughout the power-upcycle. There is an additional built-in delay after power-up that allows the analog circuits to stabilize beforethe part is activated.
標簽： Replacement 9518 NXP PCA
上傳時間： 2013-10-26
上傳用戶：13817753084
Internal Interrupts are used to respond to asynchronous requests from a certain part of themicrocontroller that needs to be serviced. Each peripheral in the TriCore as well as theBus Control Unit, the Debug Unit, the Peripheral Control Processor (PCP) and the CPUitself can generate an Interrupt Request.So what is an external Interrupt?An external Interrupt is something alike as the internal Interrupt. The difference is that anexternal Interrupt request is caused by an external event. Normally this would be a pulseon Port0 or Port1, but it can be even a signal from the input buffer of the SSC, indicatingthat a service is requested.The User’s Manual does not explain this aspect in detail so this ApNote will explain themost common form of an external Interrupt request. This ApNote will show that there is aneasy way to react on a pulse on Port0 or Port1 and to create with this impulse an InterruptService Request. Later in the second part of the document, you can find hints on how todebounce impulses to enable the use of a simple switch as the input device.Note: You will find additional information on how to setup the Interrupt System in theApNote “First steps through the TriCore Interrupt System” (AP3222xx)1. It would gobeyond the scope of this document to explain this here, but you will find selfexplanatoryexamples later on.
上傳時間： 2013-10-27
上傳用戶：zhangyigenius
The MC68HC05K0 is a low cost, low pin countsingle chip microcomputer with 504 bytes of userROM and 32 bytes of RAM. The MC68HC05K0 isa member of the 68HC05K series of devices whichare available in 16-pin DIL or SOIC packages.It uses the same CPU as the other devices in the68HC05 family and has the same instructions andregisters. Additionally, the device has a 15-stagemulti-function timer and 10 general purposebi-directional I/0 lines. A mask option is availablefor software programmable pull-downs on all ofthe I/O pins and four of the pins are capable ofgenerating interrupts.The device is ideally suited for remote-controlkeyboard applications because the pull-downs andthe interrupt drivers on the port pins allowkeyboards to be built without any externalcomponents except the keys themselves. There isno need for external pull-up or pull-down resistors,or diodes for wired-OR interrupts, as these featuresare already designed into the device.
上傳時間： 2014-01-24
上傳用戶：zl5712176
Designing withProgrammable Logicin an Analog WorldProgrammable logic devicesrevolutionized digital design over 25years ago, promising designers a blankchip to design literally any functionand program it in the field. PLDs canbe low-logic density devices that usenonvolatile sea-of-gates cells calledcomplex programmable logic devices(CPLDs) or they can be high-densitydevices based on SRAM look-up tables
標簽： Solutions Analog Xilinx FPGAs
上傳時間： 2013-11-01
上傳用戶：a67818601
This application note describes a reference system which illustrates how to build an embeddedPowerPC® system using the Xilinx 1-Gigabit Ethernet Media Access Controller processor core.This system has the PLB_Gemac configured to use Scatter/Gather Direct Memory Access andthe Serializer/Deserializer (SerDes) interface. This application note describes how to set up thespecific clocking structure required for the SerDes interface and the constraints to be added tothe UCF file. This reference system is complete with a standalone software application to testsome of the main features of this core, including access to registers, DMA capabilities, transmitand receive in loopback mode. This reference system is targeted for the ML300 evaluationboard.
上傳時間： 2013-11-01
上傳用戶：truth12
特點 最高輸入頻率 10KHz 顯示范圍0-9999（一段設定）0至999999累積量 計數速度 50/10000脈波/秒可選擇 輸入脈波具有預設刻度功能 累積量同步（批量）或非同步（批次）計數可選擇 數位化指撥設定操作簡易 計數暫時停止功能 1組報警功能 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脈波觸發電位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高輸入頻率: <10KHz (up,down,up/down mode) 輸出動作時間 : 0.1 to 99.9 second adjustable 輸出復歸方式: Manual(N) or automatic (R or C) can be modif 繼電器容量: AC 250V-5A, DC 30V-7A 顯示值范圍: 0-9999（PV,SV） 0-999999(TV) 顯示幕: Red high efficiency LEDs high 7.0mm (.276")(PV,SV) Red high efficiency LEDs high 9.2mm (.36")(TV) 參數設定方式: Touch switches 感應器電源: 12VDC +/-3%(<60mA) 記憶方式: Non-volatile E2PROM memory 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用環境條件: 0-50℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上傳時間： 2013-10-24
上傳用戶：wvbxj
特點 最高輸入頻率 10KHz 計數速度 50/10000脈波/秒可選擇 四種輸入模式可選擇(加算,減算,加減算,90度相位差加減算) 90度相位差加減算具有提高解析度4倍功能 輸入脈波具有預設刻度功能 計數暫時停止功能 3組報警功能 15BIT類比輸出功能 數位RS-485界面 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脈波觸發電位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高輸入頻率: <10KHz (up,down,up/down mode) <3KHz (quadrature mode) 輸出動作時間 : 0.1 to 99.9 second adjustable 輸出復歸方式: Manual(N) or automatic (R or C) can be modif 繼電器容量: AC 250V-5A, DC 30V-7A 顯示值范圍: -199999 to 999999 類比輸出解析度: 15 bit DAC 輸出反應速度: < 1/f+10ms(0-90%) 輸出負載能力: < 10mA for voltage mode < 10V for current mode <[(V+)-7.5V]/20mA for two-wire mode 輸出之漣波: < 0.1% F.S. 通訊位址: "01"-"FF" 傳輸速度: 19200/9600/4800/2400 selective 通信協議: Modbus RTU mode 顯示幕: Red high efficiency LEDs high 14.22mm (.56") 參數設定方式: Touch switches 感應器電源: 12VDC +/-3%(<60mA) 記憶方式: Non-volatile E2PROM memory 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用環境條件: 0-50℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上傳時間： 2013-11-23
上傳用戶：redmoons
特點 最高輸入頻率 10KHz 計數速度 50/10000脈波/秒可選擇 四種輸入模式可選擇(加算,減算,加減算,90度相位差加減算) 90度相位差加減算具有提高解析度4倍功能 輸入脈波具有預設刻度功能 前置量設定功能(二段設定)可選擇 數位化指撥設定操作簡易 計數暫時停止功能 3組報警功能 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脈波觸發電位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高輸入頻率: <10KHz (up,down,up/down mode) <5KHz (quadrature mode) 輸出動作時間 : 0.1 to 99.9 second adjustable 輸出復歸方式: Manual(N) or automatic (R or C) can be modif 繼電器容量: AC 250V-5A, DC 30V-7A 顯示值范圍: -199999 to 999999 顯示幕: Red high efficiency LEDs high 9.2mm (.36") 參數設定方式: Touch switches 感應器電源: 12VDC +/-3%(<60mA) ( 感應器電源 ) 記憶方式: Non-volatile E2PROM memory 絕緣耐壓能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用環境條件: 0-50℃(20 to 90% RH non-condensed) 存放環境條件: 0-70℃(20 to 90% RH non-condensed) CE認證: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上傳時間： 2013-11-12
上傳用戶：909000580
A Computer-On-Module, or COM, is a Module with all components necessary for a bootable host computer, packaged as a super component. A COM requires a Carrier Board to bring out I/O and to power up. COMs are used to build single board computer solutions and offer OEMs fast time-to-market with reduced development cost. Like integrated circuits, they provide OEMs with significant freedom in meeting form-fit-function requirements. For all these reasons the COM methodology has gained much popularity with OEMs in the embedded industry. COM Express® is an open industry standard for Computer-On-Modules. It is designed to be future proof and to provide a smooth transition path from legacy parallel interfaces to LVDS (Low Voltage Differential Signaling) interfaces. These include the PCI bus and parallel ATA on the one hand and PCI Express and Serial ATA on the other hand.
上傳時間： 2013-11-05
上傳用戶：Wwill
