便攜式信號采集在機器健康診斷系統中有較高的應用價值。機器健康診斷的信號特點是包括低頻信號。本文研究是為了實現簡易而且低成本的低頻便攜式信號采集。以Microchip公司單片機PIC18F1320為核心設計信號采集電路，實現了信號的采集和保存。系統采用串行電可擦除芯片24LC32A保存數據，經過有線通信，信號數據由串行口通過MAX232芯片輸送到微型計算機接收和保存，最后繪制出信號波形。 微型計算機程序采用Visual Basic編程。研究成功采樣頻率為3 kHz的復雜信號，證明該方案符合設計要求。
Abstract:
Portable signal acquisition is useful in machine health monitoring systems. The signal characteristics of machine health monitoring includes low frequency signals. The goal of this study is to realize simple, inexpensive and portable low frequency signal sampling. This paper provides the project of signal acquisition system design based on PIC18F1320 microcontroller manufactured by the Microchip Technology Incorporation to achieve signal sampling and storage. The system adopted EEPROM 24LC32A to store the signal data. The microcomputer received data VIA wired link with the MAX232 IC through the serial port. The microcomputer program, programmed in Visual Basic, received the data, stored it and plotted the signal. The study successfully samples 3kHz complicated signals and thus meets the design requirement.
MMC/SD卡以其優越的性能，在單片機嵌入式設備中得到廣泛應用。將MMC/SD卡作為外部掉電存儲介質應用于音頻信號發生器中，通過8051F330單片機上的SPI接口，實現單片機—MMC/SD卡的存儲擴展，設計了此硬件平臺上的MMC/SD卡的單片機驅動程序，并給出了相應的程序代碼，滿足音頻信號發生器的大容量存儲要求。
Abstract:
MMC/SD card is more and more widely used in the single chip embedded devices for their excellent performances.This article introduces the application of MMC/SD card as the external power down storage medium in audio signal generator. The extension technology especially for storage of single chip-MMC/SD card VIA SPI interfaces in 8051F330 single chip, including designs single chip drive program of MMC/SD card based on hardware platform,and also gives the key coding of the program. The implementation of big capacity storage is meaningful in audio signal generator.
The PCF8578 is a low power CMOS1 LCD row and column driver, designed to drive dotmatrix graphic displays at multiplex rates of 1:8, 1:16, 1:24 or 1:32. The device has40 outputs, of which 24 are programmable and configurable for the following ratios ofrows/columns: 32¤8, 24¤16, 16¤24 or 8¤32. The PCF8578 can function as a stand-alone LCDcontroller and driver for use in small systems. For larger systems it can be used inconjunction with up to 32 PCF8579s for which it has been optimized. Together these twodevices form a general purpose LCD dot matrix driver chip set, capable of driving displaysof up to 40960 dots. The PCF8578 is compatible with most microcontrollers andcommunicates VIA a two-line bidirectional bus (I2C-bus). Communication overhead isminimized by a display RAM with auto-incremented addressing and display bankswitching.
The PCA9674/74A provide general purpose remote I/O expansion for most
microcontroller families VIA the two-line bidirectional bus (I2C-bus) and is a part of the
Fast-mode Plus (Fm+) family.
FeaturesThe following standard features are provided.• Choice of RTOS scheduling policy1. Pre-emptive:Always runs the highest available task. Tasks of identical priorityshare CPU time (fully pre-emptive with round robin time slicing).2. Cooperative:Context switches only occur if a task blocks, or explicitly callstaskYIELD().• Co-routines (light weight tasks that utilise very little RAM).• Message queues• Semaphores [VIA macros]• Trace visualisation ability (requires more RAM)• Majority of source code common to all supported development tools• Wide range of ports and examples
The PCA9540B is a 1-of-2 bidirectional translating multiplexer, controlled VIA the I2C-bus.The SCL/SDA upstream pair fans out to two SCx/SDx downstream pairs, or channels.Only one SCx/SDx channel is selected at a time, determined by the contents of theprogrammable control register.
The PCA9542A is a 1-of-2 bidirectional translating multiplexer, controlled VIA the I2C-bus.The SCL/SDA upstream pair fans out to two SCx/SDx downstream pairs, or channels.Only one SCx/SDx channel is selected at a time, determined by the contents of theprogrammable control register. Two interrupt inputs, INT0 and INT1, one for each of theSCx/SDx downstream pairs, are provided. One interrupt output, INT, which acts as anAND of the two interrupt inputs, is provided.
The PCA9549 provides eight bits of high speed TTL-compatible bus switching controlledby the I2C-bus. The low ON-state resistance of the switch allows connections to be madewith minimal propagation delay. Any individual A to B channel or combination of channelscan be selected VIA the I2C-bus, determined by the contents of the programmable Controlregister. When the I2C-bus bit is HIGH (logic 1), the switch is on and data can flow fromPort A to Port B, or vice versa. When the I2C-bus bit is LOW (logic 0), the switch is open,creating a high-impedance state between the two ports, which stops the data flow.An active LOW reset input (RESET) allows the PCA9549 to recover from a situationwhere the I2C-bus is stuck in a LOW state. Pulling the RESET pin LOW resets the I2C-busstate machine and causes all the bits to be open, as does the internal power-on resetfunction.
The PCA9546A is a quad bidirectional translating switch controlled VIA the I2C-bus. TheSCL/SDA upstream pair fans out to four downstream pairs, or channels. Any individualSCx/SDx channel or combination of channels can be selected, determined by thecontents of the programmable control register.
The PCA9670 provides general purpose remote I/O expansion for most microcontrollerfamilies VIA the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plusfamily.The PCA9670 is a drop-in upgrade for the PCF8574 providing higher Fast-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all 25 mA LEDs on at the same time andmore device addresses (64 versus 8) are available to allow many more devices on the buswithout address conflicts.
