-
The PCA9537 is a 10-pin CMOS device that provides 4 bits of General Purpose parallelInput/Output (GPIO) expansion with interrupt and reset for I2C-bus/SMBus applicationsand was developed to enhance the NXP Semiconductors family of I2C-bus I/O expanders.I/O expanders provide a simple solution When additional I/O is needed for ACPI powerswitches, sensors, push-buttons, LEDs, fans, etc.
標簽：
SMBus
9537
4bit
PCA
上傳時間：
2013-10-14
上傳用戶：wuchunzhong
-
The PCA9538 is a 16-pin CMOS device that provides 8 bits of General Purpose parallelInput/Output (GPIO) expansion with interrupt and reset for I2C-bus/SMBus applicationsand was developed to enhance the NXP Semiconductors family of I2C-bus I/O expanders.I/O expanders provide a simple solution When additional I/O is needed for ACPI powerswitches, sensors, push-buttons, LEDs, fans, etc.
標簽：
SMBus
9538
8bit
PCA
上傳時間：
2014-01-24
上傳用戶：youmo81
-
The PCA9539; PCA9539R is a 24-pin CMOS device that provides 16 bits of GeneralPurpose parallel Input/Output (GPIO) expansion with interrupt and reset forI2C-bus/SMBus applications and was developed to enhance the NXP Semiconductorsfamily of I2C-bus I/O expanders. I/O expanders provide a simple solution When additionalI/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.
標簽：
9539
PCA
9539R
C-bu
上傳時間：
2013-11-10
上傳用戶：ewtrwrtwe
-
The PCA9519 is a 4-channel level translating I2C-bus/SMBus repeater that enables theprocessor low voltage 2-wire serial bus to interface with standard I2C-bus or SMBus I/O.While retaining all the operating modes and features of the I2C-bus system during thelevel shifts, it also permits extension of the I2C-bus by providing bidirectional buffering forboth the data (SDA) and the clock (SCL) lines, thus enabling the I2C-bus or SMBusmaximum capacitance of 400 pF on the higher voltage side. The SDA and SCL pins areover-voltage tolerant and are high-impedance When the PCA9519 is unpowered.
標簽：
4channel
transla
level
9519
上傳時間：
2013-11-19
上傳用戶：jisiwole
-
The PCA9541 is a 2-to-1 I2C-bus master selector designed for high reliability dual masterI2C-bus applications where system operation is required, even When one master fails orthe controller card is removed for maintenance. The two masters (for example, primaryand back-up) are located on separate I2C-buses that connect to the same downstreamI2C-bus slave devices. I2C-bus commands are sent by either I2C-bus master and are usedto select one master at a time. Either master at any time can gain control of the slavedevices if the other master is disabled or removed from the system. The failed master isisolated from the system and will not affect communication between the on-line masterand the slave devices on the downstream I2C-bus.
標簽：
master
C-bus
9541
PCA
上傳時間：
2013-10-09
上傳用戶：3294322651
-
The PCA9544A provides 4 interrupt inputs, one for each channeland one open drain interrupt output. When an interrupt is generated byany device, it will be detected by the PCA9544A and the interruptoutput will be driven LOW. The channel need not be active fordetection of the interrupt. A bit is also set in the control byte.Bits 4 – 7 of the control byte correspond to channels 0 – 3 of thePCA9544A, respectively. Therefore, if an interrupt is generated byany device connected to channel 2, the state of the interrupt inputs isloaded into the control register When a read is accomplished.Likewise, an interrupt on any device connected to channel 0 wouldcause bit 4 of the control register to be set on the read. The mastercan then address the PCA9544A and read the contents of thecontrol byte to determine which channel contains the devicegenerating the interrupt. The master can then reconfigure thePCA9544A to select this channel, and locate the device generatingthe interrupt and clear it. The interrupt clears When the deviceoriginating the interrupt clears.
標簽：
4channel
multiple
9544A
9544
上傳時間：
2014-12-28
上傳用戶：潛水的三貢
-
The PCA9549 provides eight bits of high speed TTL-compatible bus switching controlledby the I2C-bus. The low ON-state resistance of the switch allows connections to be madewith minimal propagation delay. Any individual A to B channel or combination of channelscan be selected via the I2C-bus, determined by the contents of the programmable Controlregister. When the I2C-bus bit is HIGH (logic 1), the switch is on and data can flow fromPort A to Port B, or vice versa. When the I2C-bus bit is LOW (logic 0), the switch is open,creating a high-impedance state between the two ports, which stops the data flow.An active LOW reset input (RESET) allows the PCA9549 to recover from a situationwhere the I2C-bus is stuck in a LOW state. Pulling the RESET pin LOW resets the I2C-busstate machine and causes all the bits to be open, as does the internal power-on resetfunction.
標簽：
switch
Octal
9549
with
上傳時間：
2014-11-22
上傳用戶：xcy122677
-
The PCA9555 is a 24-pin CMOS device that provides 16 bits of General Purpose parallelInput/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed toenhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvementsinclude higher drive capability, 5 V I/O tolerance, lower supply current, individual I/Oconfiguration, and smaller packaging. I/O expanders provide a simple solution Whenadditional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.The PCA9555 consists of two 8-bit Configuration (Input or Output selection); Input, Outputand Polarity Inversion (active HIGH or active LOW operation) registers. The systemmaster can enable the I/Os as either inputs or outputs by writing to the I/O configurationbits. The data for each Input or Output is kept in the corresponding Input or Outputregister. The polarity of the read register can be inverted with the Polarity Inversionregister. All registers can be read by the system master. Although pin-to-pin and I2C-busaddress compatible with the PCF8575, software changes are required due to theenhancements, and are discussed in Application Note AN469.
標簽：
C-bus
9555
SMBu
PCA
上傳時間：
2013-11-13
上傳用戶：fredguo
-
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 MicrocontrollerCore. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementationof the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision1.1.This application note describes a demonstration program that has been written for the DK3200 hardwaredemonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to workwith the device, using the HID class as a ready-made device driver for the USB connection.IN-APPLICATION-PROGRAMMING (IAP) AND IN-SYSTEM-PROGRAMMING (ISP)Since the μPSD contains two independent Flash memory arrays, the Micro Controller Unit (MCU) can executecode from one memory while erasing and programming the other. Product firmware updates in thefield can be reliably performed over any communication channel (such as CAN, Ethernet, UART, J1850)using this unique architecture. For In-Application-Programming (IAP), all code is updated through theMCU. The main advantage for the user is that the firmware can be updated remotely. The target applicationruns and takes care on its own program code and data memory.IAP is not the only method to program the firmware in μPSD devices. They can also be programmed usingIn-System-Programming (ISP). A IEEE1149.1-compliant JTAG interface is included on the μPSD. Withthis, the entire device can be rapidly programmed while soldered to the circuit board (Main Flash memory,Secondary Boot Flash memory, the PLD, and all configuration areas). This requires no MCU participation.The MCU is completely bypassed. So, the μPSD can be programmed or reprogrammed any time, anywhere, even When completely uncommitted.Both methods take place with the device in its normal hardware environment, soldered to a printed circuitboard. The IAP method cannot be used without previous use of ISP, because IAP utilizes a small amountof resident code to receive the service commands, and to perform the desired operations.
標簽：
Demonstration
3200
USB
for
上傳時間：
2014-02-27
上傳用戶：zhangzhenyu
-
計算機部件要具有通用性，適應不同系統與不同用戶的需求，設計必須模塊化。計算機部件產品(模塊)供應出現多元化。模塊之間的聯接關系要標準化，使模塊具有通用性。模塊設計必須基于一種大多數廠商認可的模塊聯接關系，即一種總線標準。總線的標準總線是一類信號線的集合是模塊間傳輸信息的公共通道，通過它，計算機各部件間可進行各種數據和命令的傳送。為使不同供應商的產品間能夠互換，給用戶更多的選擇，總線的技術規范要標準化。總線的標準制定要經周密考慮，要有嚴格的規定。總線標準（技術規范）包括以下幾部分：機械結構規范：模塊尺寸、總線插頭、總線接插件以及按裝尺寸均有統一規定。功能規范：總線每條信號線（引腳的名稱）、功能以及工作過程要有統一規定。電氣規范：總線每條信號線的有效電平、動態轉換時間、負載能力等。總線的發展情況S-100總線：產生于1975年，第一個標準化總線，為微計算機技術發展起到了推動作用。IBM-PC個人計算機采用總線結構（Industry Standard Architecture, ISA)并成為工業化的標準。先后出現8位ISA總線、16位ISA總線以及后來兼容廠商推出的EISA（Extended ISA)32位ISA總線。為了適應微處理器性能的提高及I/O模塊更高吞吐率的要求，出現了VL-Bus(VESA Local Bus)和PCI(Peripheral Component Interconnect,PCI）總線。適合小型化要求的PCMCIA(Personal Computer Memory Card International Association)總線，用于筆記本計算機的功能擴展。總線的指標計算機主機性能迅速提高,各功能模塊性能也要相應提高,這對總線性能提出更高的要求。總線主要技術指標有幾方面：總線寬度：一次操作可以傳輸的數據位數，如S100為8位，ISA為16位，EISA為32位，PCI-2可達64位。總線寬度不會超過微處理器外部數據總線的寬度。總數工作頻率：總線信號中有一個CLK時鐘，CLK越高每秒鐘傳輸的數據量越大。ISA、EISA為8MHz，PCI為33.3MHz, PCI-2可達達66.6MHz。單個數據傳輸周期：不同的傳輸方式，每個數據傳輸所用CLK周期數不同。ISA要2個，PCI用1個CLK周期。這決定總線最高數據傳輸率。5. 總線的分類與層次系統總線：是微處理器芯片對外引線信號的延伸或映射，是微處理器與片外存儲器及I/0接口傳輸信息的通路。系統總線信號按功能可分為三類：地址總線（Where）：指出數據的來源與去向。地址總線的位數決定了存儲空間的大小。系統總線：數據總線（What）提供模塊間傳輸數據的路徑，數據總線的位數決定微處理器結構的復雜度及總體性能。控制總線（When）：提供系統操作所必需的控制信號，對操作過程進行控制與定時。擴充總線：亦稱設備總線，用于系統I/O擴充。與系統總線工作頻率不同，經接口電路對系統總統信號緩沖、變換、隔離，進行不同層次的操作（ISA、EISA、MCA)局部總線：擴充總線不能滿足高性能設備（圖形、視頻、網絡）接口的要求，在系統總線與擴充總線之間插入一層總線。由于它經橋接器與系統總線直接相連，因此稱之為局部總線（PCI）。
標簽：
微型計算機
總線
上傳時間：
2013-11-09
上傳用戶：nshark
