介紹以P87LPC764型單片機為核心的延時型漏電繼電器設計方案。該方案可供用戶選擇實現額定動作電流和5倍額定動作電流下不同的延時動作時間，并有重合閘設定選擇功能。解決了以往傳統分立元件帶來的延時時間離散性大且不易實現的弊端。 Abstract: In this paper, the delay leakage relay based on P87LPC764 is introduced in detail. This system provides different relay times at rating current and 5× rating current for users and also offers superposition brake set selection function. So that it resolves many traditional problems.
上傳時間： 2013-11-08
上傳用戶：zhaiye
介紹了CAN總線和P87C591單片機的特點，給出了基于P87C591單片機的信號采集節點的軟、硬件設計，指出了硬件電路設計中應注意的問題，在軟件設計中重點介紹了節點初始化、報文發送和報文接收等子程序。 Abstract: The features of CAN Bus and the microcontroller P87C591 are introduced, and the design of hardware circuit and soft configuration of the signals collection node based on P87C591 are presented. The problems in designing hardware circuit are discussed.Initialization subprogram, transmiting subprogram and receiving subprogram are emphasized in soft configuration.
標簽： P87C591 信號采集 節點
上傳時間： 2013-11-03
上傳用戶：BIBI
以S3C825A為例介紹三星公司SAM8系列單片機的內部結構及其軟件開發環境，詳細描述采用混合編程法來對SAM8系列單片機進行軟件設計的一般方法，最后給出用混合編程法對S3C825A進行軟件設計的具體應用實例。 Abstract: With S3C825A,this paper firstly introduces the SAM8 series single-chip microcontrollers and their software development environment, then introduces mixed programming technology for SAM8 series single-chip microcontrollers. In the end, the application program is also given.
標簽： S3C825A SAM8 單片機 軟件設計
上傳時間： 2013-12-09
上傳用戶：ZZJ886
基于幅移鍵控技術ASK（Amplitude-Shift Keying），以C8051F340單片機作為監測終端控制器，C8051F330D單片機作為探測節點控制器，采用半雙工的通信方式，通過監控終端和探測節點的無線收發電路，實現數據的雙向無線傳輸。收發電路采用直徑為0.8 mm的漆包線自行繞制成圓形空心線圈天線，天線直徑為（3.4±0.3）cm。試驗表明，探測節點與監測終端的通信距離為24 cm，通過橋接方式，節點收發功率為102 mW時，節點間的通信距離可達20 cm。與傳統無線收發模塊相比，該無線收發電路在受體積、功耗、成本限制的場合有廣闊的應用前景。 Abstract: Based on ASK technology and with the C8051F340 and C8051F330D MCU as the controller， using half-duplex communication mode， this paper achieves bi-directional data transfer. Transceiver circuit constituted by enameled wire which diameter is 0.8mm and wound into a diameter （3.4±0.3） cm circular hollow coil antenna. Tests show that the communication distance between detection and monitoring of the terminal is 24cm，the distance is up to 20cm between two nodes when using the manner of bridging and the node transceiver power is 102mW. Compared with the conventional wireless transceiver modules， the circuit has wide application prospect in small size， low cost and low power consumption and other characteristics.
標簽： C8051F 單片機 無線收發 電路設計
上傳時間： 2013-10-19
上傳用戶：xz85592677
在需要實時大量輸入漢字的顯示控制處理應用中，利用傳統單片機實現顯示控制的設計方法是較難實現的。帶漢字字庫的液晶模塊的使用使得小容量ROM單片機的大量漢字信息輸入與顯示成為可能。提出了針對漢字字庫編碼的二級索引拼音輸入檢索方法,介紹了以ST7920作為控制器的帶漢字字庫的液晶顯示模塊的接口方法及漢字顯示和控制原理，給出了通用計算機鍵盤在單片機中的串行接口，采用該技術可大大增強單片機的漢字輸入功能。為小容量ROM單片機的大批量漢字信息處理提供了一種漢字輸入解決方案。 Abstract: It is difficult to realize Chinese characters input method based on the embedded system by using the traditional design method of display control. It is possible to input and display Chinese characters based on the embedded system with the ROM of small content by using the LCD module with Chinese characters.Chinese characters input method of the quadric index recall in allusion to Chinese characters code is brought forward.The interface and the principle of Chinese characters display control based on the LCD module controlled with the ST7920 is introduced too.The serial interface of the computer keyboard in common use and the embedded system is given at the same time. It can enhance the embedded system function of Chinese characters input by using this technology, and provide a kind of Chinese characters input scheme for the embedded system with small capacity ROM.
上傳時間： 2013-11-19
上傳用戶：jhksyghr
為了提高環境參數采集的自動化水平，提升效率，設計了無線傳感器系統。本系統運用了傳感器技術、通信技術和單片機技術，實現了對環境溫度、濕度、光照度以及可燃性氣體濃度等參數的檢測。它能夠?qū)崟r(shí)地與上位機進行無線通信，滿足對環境參數實時監測的要求。 Abstract: In order to increase the degree of automation and improve the efficiency of the environment monitoring parameters，the wireless sensor system was developed.Combining with the technique of sensor,automatic monitoring，communication and single-chip microcomputer，it realized real-time monitoring environment parameters,such as temperature，humidity，illumination，concentration of com- bustible gas and so on.At the same time it can communicate with upper personal computers，satisfy the desire of real-time monitoring.
上傳時間： 2013-11-22
上傳用戶：longlong12345678
為解決輸油管道溫度壓力參數實時監測的問題，設計了以C8051F930單片機作為控制核心的超低功耗輸油管道溫度壓力遠程監測系統。現場儀表使用高精度電橋采集數據，通過433 MHz短距離無線通信網絡與遠程終端RTU進行通信，RTU通過GPRS網絡與PC上位機進行遠程數據傳輸，在上位機中實現數據存儲和圖形化界面顯示，從而實現輸油管道溫度壓力參數的實時監測和異常報警。經實驗證明，該系統的12位數據采集精度滿足設計要求，漏碼率小于1%，正常工作時間超過5個月，能實時有效地監測輸油管道的溫度壓力參數，節省大量人工成本，有效預防管道參數異常造成的經濟損失和環境污染。 Abstract: In order to solve the problems on real-time monitoring of pipeline temperature and pressure parameters， the ultra-low power remote pipeline temperature and pressure monitoring system was designed by using the single chip processor C8051F930 as the control core. The high-precision electric bridge was used in field instruments for data collection， the 433MHz short-range wireless communication network was used to make communication between field instrument and RTU， the GPRS was used by the RTU to transmit data to the PC host computer， and the data was stored and displayed in the PC host computer， so the real-time monitoring and exception alerts of pipeline temperature and pressure parameters were achieved. The experiment proves that the system of which error rate is less than 1% over five months working with the 12-bit data acquisition accuracy can effectively monitor the pipeline temperature and pressure parameters in real time， it saves a lot of labor costs and effectively prevents environmental pollution and economic losses caused by abnormal channel parameters.
標簽： C8051F930 溫度 壓力 遠程監測系統
上傳時間： 2013-11-07
上傳用戶：cuibaigao
為解決傳統可視倒車?yán)走_(dá)視頻字符疊加器結構復雜，可靠性差，成本高昂等問題，在可視倒車?yán)走_(dá)設計中采用視頻字符發生器芯片MAX7456。該芯片集成了所有用于產生用戶定義OSD，并將其插入視頻信號中所需的全部功能，僅需少量的外圍阻容元件即可正常工作。給出了以MAX7456為核心的可視倒車?yán)走_(dá)的軟、硬件實現方案及設計實例。該方案具有電路結構簡單、價格低廉、符合人體視覺習慣的特點。經實際裝車測試，按該方案設計的可視倒車?yán)走_(dá)視場清晰、提示字符醒目、工作可靠，可有效降低駕駛員倒車時的工作強度、減少倒車事故的發生。 Abstract: A new video and text generation chip，MAX7456，was used in the design of video parking sensor in order to simplify system structure，improve reliability and reduce cost. This chip included all the necessary functions to generate user-defined OSDs and to add them into the video signals. It could be put into work with addition of just a small number of resistances and capacitors. This paper provided software and hardware implementation solutions and design example based on the chip. The system had the characteristics of simplicity in circuit structure，lower cost，and comfort for the nature of human vision. Loading road test demonstrates high video and text display quality and reliable performance，which makes the driver easy to see backward and reduces chance of accidents.
標簽： 7456 MAX 可視倒車 中的應用
上傳時間： 2013-12-10
上傳用戶：qiaoyue
針對船舶氣象儀保障維修而設計的船舶氣象儀測試系統，包括信息處理終端、主儀器檢測模塊、傳感器檢測模塊，各個模塊都采用基于AVR單片機的嵌入式系統，模塊之間通過CAN總線進行通信。結果表明，船舶氣象儀測試系統能夠快速檢測船舶氣象儀故障，與單純依靠人工方式排查故障相比，故障檢測時間縮短了60%以上。 Abstract: The test system of ship meteorological instrument was developed to satisfy the maintenance of ship meteorological instruments，which composed of information processing terminal， testing module of main instrument and testing module of sensors. Each of these modules included an embedded system based on microcontroller of AVR series and communicated with other module by CAN bus. The results show that the test system can judge the fault of ship meteorological instrument quickly and shorten the fault detection time as much as 60% compared with simple manual troubleshooting.
標簽： AVR 單片機 氣象儀 測試系統
上傳時間： 2013-11-23
上傳用戶：stvnash
將現行的供暖計費方式由按建筑面積計費變?yōu)榘聪牡臒崮苡?jì)費是供暖計費方式發展趨勢，為了滿足這一計費方式變化的需要，設計了基于IC卡的預付費式新型供暖計費系統，通過測量用戶采暖系統進出口的溫度和流量，計算用戶消耗的熱能，利用IC卡記錄用戶預付費的金額和當年熱能的單價，根據熱能消耗和當年熱能的單價計算用戶采暖費，根據實際發生的供暖費用和預付費金額控制供暖的開停，這一計費方式的變化使供暖計費更趨合理。 Abstract: It is trend that the mode of heat charging is changed from billing by building area to by thermal energy. In order to meet the needs of heat charging mode changing， a new system of heat charging based on IC card is proposed. The user?蒺s energy consumption is calculated by measuring the user inlet and outlet temperature and flow，using the IC card to record the prepaid amount and the current price of heat. The user?蒺s heating costs is calculated according to energy consumption and current price， according to actual heating costs and prepaid amount，the system controls the heating opening or stopping. It is more reasonable that calculated heating costs by user heat consumption
標簽： IC卡 計費 系統設計
上傳時間： 2013-10-14
上傳用戶：大融融rr
蟲蟲下載站版權所有 京ICP備2021023401號-1
