A MEMS microphone IC is unique among Analog Devices, Inc., products in that its input is an acoustic pressure wave. For this reason, some specifications included in the data sheets for these parts may not be familiar, or familiar specifications may be applied in unfamiliar ways. This application note explains the specifica-tions and terms found in MEMS microphone data sheets so that the microphone can be appropriately designed into a system.
上傳時間： 2013-10-31
上傳用戶：masochism
Abstract: If sensitive analog systems are run from one supply without the sufficient bypassing to eliminate noise,
上傳時間： 2013-11-23
上傳用戶：qiulin1010
Abstract: This design idea explains how to implement an 8-bit analog-to-digital converter (ADC), using a microcontroller
上傳時間： 2013-10-30
上傳用戶：愛死愛死
Abstract: The DS4830 optical microcontroller's analog-to-digital converter (ADC) offset can change with temperature and gainselection. However, the DS4830 allows users to measure the ADC internal offset. The measured ADC offset is added to the ADCoffset register to nullify the offset error. This application note demonstrates the DS4830's ADC internal offset calibration in theapplication program.
上傳時間： 2014-12-23
上傳用戶：萍水相逢
Abstract: This tutorial discusses methods for digitally adjusting the output voltage of a DC-DC converter. The digital adjustmentmethods are with a digital-to-analog converter (DAC), a trim pot (digital potentiometer), and PWM output of a microprocessor.Each method is assessed and several DACs and digital potentiometers presented.
上傳時間： 2013-11-20
上傳用戶：zycidjl
Abstract: This article discusses application circuits for Maxim force/sense digital-to-analog converters (DACs). Applications include:selectable fixed-gain DAC, programmable gain DAC, photodiode bias control, amperometric sensor control, digitally programmablecurrent source, Kelvin load sensing, temperature sensing, and high current DAC output. A brief description of the various DAC outputconfigurations is also given.
標簽： DAC
上傳時間： 2013-11-04
上傳用戶：youmo81
Abstract: Using a DAC and a microprocessor supervisor, the system safety can be improved in industrial controllers, programmablelogiccontrollers (PLC), and data-acquisition systems. The analog output is set to zero-scale (or pin-programmable midscale) when amicroprocessor failure, optocoupler failure, or undervoltage condition occurs. A simple application is shown on how to implement thisfunction.
上傳時間： 2013-10-17
上傳用戶：sjb555
以某高速實時頻譜儀為應用背景，論述了5 Gsps采樣率的高速數據采集系統的構成和設計要點，著重分析了采集系統的關鍵部分高速ADC（analog to digital，模數轉換器）的設計、系統采樣時鐘設計、模數混合信號完整性設計、電磁兼容性設計和基于總線和接口標準（PCI Express）的數據傳輸和處理軟件設計。在實現了系統硬件的基礎上，采用Xilinx公司ISE軟件的在線邏輯分析儀（ChipScope Pro）測試了ADC和采樣時鐘的性能，實測表明整體指標達到設計要求。給出上位機對采集數據進行處理的結果，表明系統實現了數據的實時采集存儲功能。
上傳時間： 2014-11-26
上傳用戶：黃蛋的蛋黃
Precision 16-bit analog outputs with softwareconfigurableoutput ranges are often needed in industrialprocess control equipment, analytical and scientificinstruments and automatic test equipment. In the past,designing a universal output module was a daunting taskand the cost and PCB real estate associated with thisfunction were problematic, if not prohibitive.
上傳時間： 2014-12-23
上傳用戶：如果你也聽說
High input impedance and a wide input range are twohighly desirable features in a precision analog-to-digitalconverter, and the LTC®2449 delta-sigma ADC has both.With just a few external components, the LTC2449 formsan exceptional measurement system with very high inputimpedance and an input range that extends 300mV beyondthe supply rails.
上傳時間： 2013-11-02
上傳用戶：ywcftc277
