Abstract: Many industrial/scientific/medical (ISM) band radio frequency (RF) products use crystal oscillators to generate areference for the phase-locked loop (PLL)-based local oscillator (LO). This tutorial provides a basic description of theISM-RF Crystal Calculator, which can be used to calculate various impacts on crystal frequency accuracy and startupmargin for such an LO.
Abstract: A resistive feedback network is often used to set the output voltage of a power supply. A mechanical potentiometer (pot)conveniently solves the problem of adjusting a power supply. For easier automatic calibration, a mechanical pot can be replaced witha digital pot. This application note presents a calibration solution that uses a digital pot, because digipots are smaller, do not movewith age or vibration, and can be recalibrated remotely. This proposed solution reduces the susceptibility of the system to thetolerance of the digital pot's end-to-end resistance, making the solution optimal fordesigners. This application note also explainssome of the equations required to calculate the resistor chain values and to use a digital pot in this way. A spreadsheet withstandard reisistor values is available for easy calculations.
The MAX9257/MAX9258 programmable serializer/deserializer (SerDes) devices transfer both video data and control signals over the same twisted-pair cable. However, control data can only be transmitted during the vertical blank time, which is indicated by the control-channel-enabled output (CCEN) signal. The electronic control unit (ECU) firmware designer needs to know how quickly to respond to the CCEN signal before it times out and how to calculate this duration. This application note describes how to calculate the duration of the CCEN for the MAX9257/MAX9258 SerDes chipset. The calculation is based on STO timeout, clock frequency, and UART bit timing. The CCEN duration is programmable and can be closed if not in use.
為提高太陽能的利用率，以ATmega8單片機為控制核心，設計了一套光電跟蹤與視日運動軌跡跟蹤互補控制的雙軸太陽跟蹤器。該跟蹤器在晴天時，利用光敏電阻采集光強判斷太陽位置,控制步進電機實現光電跟蹤；在陰天時，采集時鐘器件PCF8583的時間信息,計算當前太陽位置來實現視日運動軌跡跟蹤。實驗表明：該太陽跟蹤器能在不同天氣狀況下對太陽進行較準確地跟蹤，能量接收效率提高了30%，達到充分利用太陽能的目的。
Abstract:
To improve the utilization rate of solar energy，a kind of solar tracking controller which effectively combined the sun angle tracking and photo electric tracking based on ATmega8is designed.In the sunny days，the solar tracking con-troller determines the sun's position by using photosensitive resistances to collect light intensity and control stepper motors to achieve photo electric tracking，n cloudy days，it collects clock chip PCF8583time information to calculate the current position of the sun and achieve the sun angle tracking.Experimental results show the solar tracking controller accurately tracks the sun in different weather conditions，improves received energy efficiency by30%and reaches the purpose of full use of solar energy.
Abstract: Many industrial/scientific/medical (ISM) band radio frequency (RF) receivers use an external Sallen-Key datafilter and a data slicer to generate the baseband digital output. This tutorial describes the ISM-RF Baseband Calculator,which can be used to calculate the filter capacitor values and the data slicer RC components, while providing a visualexample of the baseband signals.
This program will ask how many numbers you want to find the average of, then it will allow you to enter your numbers(yes they can even be decimals) then it will calculate the mean, median, mode and range of what you enter.
51串行令牌格式 a51編譯
Read data from serial port
and write into buffer DPTR pointed in XRAM if a data frame is
received and calculate the check sum
if a information frame is received return control byte only
加密算法
Test Driver for Crypto++, a C++ Class Library of Cryptographic Primitives:
- To generate an RSA key
cryptest g
- To encrypt and decrypt a string using RSA
cryptest r
- To calculate MD5, SHS, and RIPEMD-160 message digests:
cryptest m file
- To encrypt and decrypt a string using DES-EDE in CBC mode:
cryptest t
- To encrypt or decrypt a file
cryptest e|d input output
- To share a file into shadows:
cryptest s <pieces> <pieces-needed> file
(make sure file has no extension, if you re running this under DOS)
- To reconstruct a file from shadows:
cryptest j output file1 file2 [....]
- To gzip a file:
cryptest z <compression-level> input output
- To gunzip a file:
cryptest u input output
- To run validation tests:
cryptest v
- To run benchmarks:
cryptest b [time for each benchmark in seconds]
