在確定采用CAN總線作為系統的通訊標準后，如何選擇合適的處理器芯片就將成為很重要的問題，是采用內部帶有CAN控制器的單片機，還是采用SJA1000等片外CAN控制器，采用的芯片是否能滿足系弘的實時性要求。
上傳時間： 2013-10-26
上傳用戶：xiaohanhaowei
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 MicrocontrollerCore. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementationof the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision1.1.This application note describes a demonstration program that has been written for the DK3200 hardwaredemonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to workwith the device, using the HID class as a ready-made device driver for the USB connection.IN-APPLICATION-PROGRAMMING (IAP) AND IN-SYSTEM-PROGRAMMING (ISP)Since the μPSD contains two independent Flash memory arrays, the Micro Controller Unit (MCU) can executecode from one memory while erasing and programming the other. Product firmware updates in thefield can be reliably performed over any communication channel (such as CAN, Ethernet, UART, J1850)using this unique architecture. For In-Application-Programming (IAP), all code is updated through theMCU. The main advantage for the user is that the firmware can be updated remotely. The target applicationruns and takes care on its own program code and data memory.IAP is not the only method to program the firmware in μPSD devices. They can also be programmed usingIn-System-Programming (ISP). A IEEE1149.1-compliant JTAG interface is included on the μPSD. Withthis, the entire device can be rapidly programmed while soldered to the circuit board (Main Flash memory,Secondary Boot Flash memory, the PLD, and all configuration areas). This requires no MCU participation.The MCU is completely bypassed. So, the μPSD can be programmed or reprogrammed any time, anywhere, even when completely uncommitted.Both methods take place with the device in its normal hardware environment, soldered to a printed circuitboard. The IAP method cannot be used without previous use of ISP, because IAP utilizes a small amountof resident code to receive the service commands, and to perform the desired operations.
標簽： Demonstration 3200 USB for
上傳時間： 2014-02-27
上傳用戶：zhangzhenyu
This application note shows how to write an Inter Integrated Circuit bus driver (I²C) for the Philips P90CL301micro-controller.It is not only an example of writing a driver, but it also includes a set of application interface software routines toquickly implement a complete I²C multi-master system application.For specific applications the user will have to make minimal changes in the driver program. Using the drivermeans linking modules to your application software and including a header-file into the application sourceprograms. A small example program of how to use the driver is listed.The driver supports i.a. polled or interrupt driven message handling, slave message transfers and multi-mastersystem applications. Furthermore, it is made suitable for use in conjunction with real time operating systems, likepSOS+.
上傳時間： 2013-11-23
上傳用戶：weixiao99
This application note demonstrates how to write an Inter Integrated Circuit bus driver (I2C) for the XA-S3 16-bitMicrocontroller from Philips Semiconductors.Not only the driver software is given. This note also contains a set of (example) interface routines and a smalldemo application program. All together it offers the user a quick start in writing a complete I2C system applicationwith the PXAS3x.The driver routines support interrupt driven single master transfers. Furthermore, the routines are suitable foruse in conjunction with real time operating systems.
上傳時間： 2013-11-02
上傳用戶：zw380105939
基于P87 C591的CAN總線系統智能節點設計Design of CAN System Intelligent Node Based on P87C591 給出了基于帶CAN控制器的單片8位微控制器P87C591的智能節點的硬件電路及軟件結構，詳細介紹了設計中的難點及實現過程中應注意的問題。關鍵詞:CAN總線;智能節點 Abstract:A h ardc ircuita nds oftw arec onfigurationo fth ei ntelligentnode based on a microcontroller with CAN controller P87C591 arepresented.E speciallyt hec ruxi nd esigninga ndt hep roblemst hatshould be paid attention in realizing are discussed in details.Keyw ords:C AN;in telligentn ode CA N 總線 是德國Bosch從20世紀80年代初為解決現代汽車中眾多的控制與測試儀器之間的數據交換而開發的一種串行數據通信協議，它是一種多主總線，通信介質可以是雙絞線、同軸電纜或光導纖維。由于CAN總線具有較強的糾錯能力，支持差分收發，因而適合高噪聲環境。并具有較遠的傳輸距離，適用于許多領域的分布式測控系統。目前已在工業自動化、建筑物環境控制、醫療設備等許多領域得到廣泛的應用。CAN已成為國際標準化組織IS011898標準。
上傳時間： 2013-10-30
上傳用戶：xymbian
CAN與RS232轉換節點的設計與實現 介紹將CAN總線接口與RS232總線接口相互轉換的設計方法和2種總線電平轉換關系，實現CAN總線與各模塊的接口設計，制定了相應的軟硬件設計方案，并給出軟件設計流程圖以及部分硬件設計原理圖。為CAN總線與RS232總線互聯提供了一種方法，對CAN總線與RS232總線接口設備的互聯和廣泛應用的實現具有重要意義。關鍵詞：CAN總線；RS-232總線；串行通信Design and Realization of CAN and RS232 Transformation NodeZHOU Wei, CHENG Xiao-hong(Information Institute, Wuhan University of Technology, Wuhan 430070)【Abstract】This paper introduces one design method of the CAN bus interface and the RS232 bus interface interconversion, emphasizes two kindof bus level transformation relations, realizes the CAN bus and various modules connection design, formulates the design proposal of correspondingsoftware and hardware, and gives the flow chart of software design as well as the partial schematic diagram of hardware design. It providesonemethod for the CAN bus and the RS232 bus interconnection, has the vital significance to widespread application realization of the CAN busand theRS232 bus interface equipment interconnection.【Key words】CAN bus; RS-232 bus; serial communication
上傳時間： 2013-11-04
上傳用戶：leesuper
簡要介紹了CAN總線技術與USB總線技術的特點，給出了通過將兩特點相結合，并選用微控制器AT89C52堯USB控制芯片CH372和獨立CAN控制芯片SJA1000實現USB-CAN數據傳輸系統的設計方案遙該系統不但能實現CAN總線與USB總線之間的數據轉化，并可在兩臺主機配合下完成兩個節點之間數據的透明傳輸。關鍵詞 通用串行總線USB CAN總線 數據通信
上傳時間： 2013-10-15
上傳用戶：plsee
基于CAN總線的智能尋位制造系統 智能尋位制造系統的組成網絡化智能尋位制造系統的概念是將智能尋位,工藝規劃# 加工信息生成# 加工設備控制等分布于制造系統中不同物理位置的獨立單元! 借助實時控制網絡集成為一有機整體! 從而實現單元間的高速信息交換! 并通過管理計算機中的動態調度軟件! 協調整個系統的高效運行" 據此思路構成的網絡化智能尋位制造系統的總體結構如圖所示.
上傳時間： 2013-11-13
上傳用戶：wdq1111
針對傳統語音通信系統存在的地址編碼繁雜、通信模式單一、難于維護的缺陷，設計了一款適用于工業現場的多功能語音通信系統。在排隊論的基礎上,對CAN總線語音通信系統進行了理論分析，重點介紹了CAN總線的軟硬件設計。對系統的性能測試結果表明，系統的CAN幀丟失率<0.5‰,語音質量能通過主觀試聽和客觀測試,整體系統工作良好。
上傳時間： 2014-12-28
上傳用戶：aa54
CAN總線初學者的CAN入門書
上傳時間： 2013-10-11
上傳用戶：aix008
